Show Tec Sunstrip Active MKII 110V V1 User manual

Sunstrip Active MKII 110V V1
Highlite International B.V. –Vestastraat 2 –6468 EX –Kerkrade –the Netherlands
Ordercode: 30751
MANUAL
ENGLISH

1
Ordercode: 30751
Sunstrip Active MKII 110V
Table of contents
Warning ...............................................................................................................................................................................2
Safety Instructions .........................................................................................................................................................2
Operating Determinations ..........................................................................................................................................4
Rigging ............................................................................................................................................................................4
Connection with the mains.........................................................................................................................................5
Return Procedure..........................................................................................................................................................6
Claims..............................................................................................................................................................................6
Description of the device.................................................................................................................................................7
Optional accessories....................................................................................................................................................7
Frontside..........................................................................................................................................................................7
Backside .........................................................................................................................................................................8
Installation...........................................................................................................................................................................8
Installing the Lamp........................................................................................................................................................9
Set Up and Operation .....................................................................................................................................................10
Control Modes.............................................................................................................................................................10
One Sunstrip Active (Chase mode) .....................................................................................................................10
Multiple Sunstrips Active (DMX Control) ..............................................................................................................10
Fixture Linking...............................................................................................................................................................11
Data Cabling...............................................................................................................................................................11
Control Panel ...............................................................................................................................................................12
Control Mode ..............................................................................................................................................................12
DMX Addressing ..........................................................................................................................................................12
Menu Overview...........................................................................................................................................................13
Main Menu Options....................................................................................................................................................13
1. DMX Mode ...............................................................................................................................................................13
1.1 DMX address ......................................................................................................................................................13
1.2 DMX configuration ............................................................................................................................................14
2. Chase Mode............................................................................................................................................................14
2.1 Chase program .................................................................................................................................................14
2.2 Chase direction .................................................................................................................................................14
2.3 Chase speed ......................................................................................................................................................14
2.4 Chase dimmer ...................................................................................................................................................14
Edit welcome text .......................................................................................................................................................15
DMX Channels .............................................................................................................................................................15
1 DMX channel.........................................................................................................................................................15
2 DMX channels .......................................................................................................................................................15
5 DMX channels .......................................................................................................................................................16
10 DMX channels .....................................................................................................................................................17
Maintenance....................................................................................................................................................................17
Changing the Lamp...................................................................................................................................................18
Replacing the Fuse.....................................................................................................................................................18
Troubleshooting ...............................................................................................................................................................18
No Light.........................................................................................................................................................................18
No Response to DMX..................................................................................................................................................18
Product Specifications....................................................................................................................................................20
Dimensions........................................................................................................................................................................21
Notes ..................................................................................................................................................................................22

2
Ordercode: 30751
Sunstrip Active MKII 110V
Warning
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure
that all parts are present, and have been received in good condition. Notify the dealer immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be
returned to the factory, it is important that the fixture be returned in the original factory box and packing.
Your shipment includes:
●Showtec Sunstrip Active 110V
●2 brackets incl. screws
●Neutrik Powercon to US plug power cable 1,5m
●User manual
LED Expected Lifespan
LEDs gradually decline in brightness over time. HEAT is the dominant factor that leads to the acceleration
of this decline. Packaged in clusters, LEDs exhibit higher operating temperatures than in ideal or singular
optimum conditions. For this reason, when all color LEDs are used at their fullest intensity, life of the LEDs is
significantly reduced. If improving the lifespan is of higher priority, place care in providing for lower
operational temperatures. This may include climatic-environmental and the reduction of overall
projection intensity.
Safety Instructions
Every person involved with the installation, operation and maintenance of this device has to:
●be qualified
●follow the instructions of this manual
Before the initial start-up, please make sure that there is no damage caused by transportation.
Should there be any, consult your dealer and do not use the device.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes contained in this manual.
Please consider that damages caused by manual modifications to the device are not subject to
warranty.This device contains no user-serviceable parts. Refer servicing to qualified technicians only.

3
Ordercode: 30751
Sunstrip Active MKII 110V
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual or any unauthorized modification to the device.
●Never let the power cord come into contact with other cables! Handle the power cord and all
connections with the mains with particular caution!
●Never modify, bend, mechanically strain, put pressure on, pull or heat up the power cord.
●Never strain the cable insert or the female part in the device. There must always be sufficient cable
going to the device. Otherwise, the cable will be damaged, which can cause serious damage.
●Never remove warning or informative labels from the unit.
●Never use anything to cover the ground contact.
●Never lift the device holding it by the projector-head, as the mechanics may be damaged. Always
hold the device by the transport handles.
●Never place any material over the lens.
●Never look directly into the light source.
●Never use the device without the lamp.
●Never ignite the lamp if the objective lens or any housing cover is open, as discharge lamps may
expose and emit a high ultraviolet radiation, which may cause burns.
●In case of strobe fixtures: Never operate the stroboscope without protective shield! When the shield is
cracked, replace it before using the device again.
●Never leave any cables lying around.
●Never use the device during thunderstorms, unplug the device immediately.
●Never leave various parts of the packaging (plastic bags, polystyrene foam, nails, etc.) within
children’s reach, as they are potential sources of danger.
●Do not insert objects into air vents.
●Do not open the device and do not modify the device.
●Do not switch the device on and off in short intervals, as this will reduce the device’s life.
●Do not touch the device’s housing bare-handed during its operation (housing becomes very hot).
Allow the device to cool for at least 5 minutes before handling.
●Do not shake the device. Avoid brute force when installing or operating the device.
●Do not install lamps of higher wattage.
●Only use the appropriate lamp for your unit. Note that product versions, that use other lamps, may
be offered in the future. Check your product specification label for information.
●Only use the device indoors, avoid contact with water or other liquids (only applies to devices with
IP<=65).
●Only operate the device after having checked if the housing is firmly closed and all screws are tightly
fastened.
●Only operate the device after having familiarized with its functions.
●Avoid flames and do not put close to flammable liquids or gases.
●Always replace the lamp, when it is damaged or deformed due to the heat.
●Always keep the case closed while operating.
●Always allow a free air space of at least 50 cm around the unit for ventilation.
●Always disconnect power from the mains, when device is not used, before cleaning or when
replacing lamp! Only handle the power cord holding it by the plug. Never pull out the plug by
tugging the power cord.
●Make sure that the device is not exposed to extreme heat, moisture or dust.
●Make sure that the available voltage is not higher than stated on the rear panel.
●Make sure that the power cord is never crimped or damaged. Check the device and the power
cord from time to time.
●Make sure that the core diameter of extension cords and power cords is sufficient for the required
power consumption of the device.
●If the lens is obviously damaged, it has to be replaced to prevent its functions from being impaired,
due to cracks or deep scratches.
●If the external cable is damaged, it has to be replaced by a qualified technician.
●If device was dropped or struck, disconnect mains power supply immediately. Have a qualified
engineer inspect for safety before operating.
●If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not
switch it on immediately. The arising condensation water might damage your device. Leave the
device switched off until it has reached room temperature.

4
Ordercode: 30751
Sunstrip Active MKII 110V
●If your Showtec device fails to work properly, discontinue the use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your Showtec dealer for service.
●For adult use only. The device must be installed beyond the reach of children. Never leave the unit
running unattended.
●Never attempt to bypass the thermostatic switch or fuses.
●For replacement use fuses of same type and rating only.
●The user is responsible for correct positioning and operating of the device. The manufacturer will not
accept liability for damages caused by the misuse or incorrect installation of this device.
●This device falls under protection class I. Therefore it is essential to connect the yellow/green
conductor to earth.
●During the initial start-up, some smoke or smell may arise. This is a normal process and does not
necessarily mean that the device is defective.
●Allow time to cool down, before replacing lamp.
●For replacement use lamps of same type and rating only.
●Repairs, servicing and electric connection must be carried out by a qualified technician.
●WARRANTY: Till one year after date of purchase.
Operating Determinations
●This device is not designed for permanent operation. Consistent operation breaks will ensure that the
device will serve you for a long time without defects.
●The minimum distance between light output and the illuminated surface must be bigger than 1
meter. (This distance may differ depending on the model. The exact minimum distance will be
mentioned in the corresponding manual.)
●To eliminate wear and improve lifespan, during periods of non-use, completely disconnect from
power via breaker or by unplugging.
●The maximum ambient temperature ta= 40°C must never be exceeded.
●The relative humidity must not exceed 50 % with an ambient temperature of 40°C.
●If this device is operated in any other way than the one described in this manual, the product may
suffer damages and the warranty becomes void.
●Any other operation may lead to dangers like short-circuit, burns, electric shock, crash, etc.
You endanger your own safety and the safety of others!
Rigging
Please follow the European and national guidelines concerning rigging, trussing and all
other safety issues.
Do not attempt the installation yourself !
Always let the installation be carried out by an authorized dealer !
Procedure:
●If the Sunstrip Active is lowered from the ceiling or high joists, professional trussing systems have to be
used.
●Use a clamp to mount the Sunstrip Active with the mounting bracket, to the trussing system.
●The Sunstrip Active must never be fixed swinging freely in the room.
●The installation must always be secured with a safety attachment, e.g. an appropriate safety net or
safety cable.
●When rigging, derigging or servicing the Sunstrip Active, always make sure, that the area below the
installation site is secured and that there are not any unauthorized people around.

5
Ordercode: 30751
Sunstrip Active MKII 110V
The Sunstrip Active MKII 110V can be placed on a flat stage floor or mounted to any kind of truss with a
clamp.
Improper installation can cause serious injuries and/or damage of property!
Connection with the mains
Connect the device to the mains with the power-plug.
Always check if the right color cable is connected to the right place.
International
EU Cable
UK Cable
US Cable
Pin
L
BROWN
RED
YELLOW/COPPER
PHASE
N
BLUE
BLACK
SILVER
NEUTRAL
YELLOW/GREEN
GREEN
GREEN
PROTECTIVE
GROUND
Make sure that the device is always properly connected to the earth!
Improper installation can cause serious injuries and/or damage of property!

6
Ordercode: 30751
Sunstrip Active MKII 110V
Return Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned
without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Call Highlite 0031-455667723 or mail [e-mail] and request an RMA prior to shipping the
fixture. Be prepared to provide the model number, serial number and a brief description of the cause for
the return. Be sure to properly pack fixture, any shipping damage resulting from inadequate packaging is
the customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace
product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.
Note: If you are given an RMA number, please include the following information on a piece of paper
inside the box:
01) Your name
02) Your address
03) Your phone number
04) A brief description of the symptoms
Claims
The client has the obligation to check the delivered goods immediately upon delivery for any short-
comings and/or visible defects, or perform this check after our announcement that the goods are at their
disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise.
It is the customer's responsibility to report and submit claims with the shipper in the event that a fixture is
damaged due to shipping. Transportation damage has to be reported to us within one day after receipt
of the delivery.
Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with
a letter defining the reason for return shipment. Non-prepaid return shipments will be refused, unless
agreed otherwise in writing.
Complaints against us must be prepared in writing or sent by fax within 10 working days after receipt of
the invoice. After this period complaints will not be handled anymore.
Complaints will only then be considered if the client has so far complied with all parts of the agreement,
regardless of the agreement from which the obligation is resulting.

7
Ordercode: 30751
Sunstrip Active MKII 110V
Description of the device
Features
The Sunstrip Active 110V is a 110V version of the already popular Sunstrip Active MKII. It is the most
versatile fixture including 10 pcs Sunstrip lamp GU10. This Sunstrip is specially designed for countries which
have a 110V power connection.
●Invert function
●Programmable name in start screen
●Input voltage: 110V, 50/60Hz
●Power consumption: 500W
●DMX channels: 1, 2, 5 or 10 channels
●4-digit LED display for easy setup
●Light source: 10 x 110V/50W GU10 (Ordercode: SPHK498)
●Socket: GU10
●Lumen: 300lm (each Lamp)
●Control modes: Chase mode, DMX mode
●Control protocol: DMX-512
●Dimmer: 0-100%
●Beam Angle: 35°
●Protection rate: IP-20
●Power Connector: Neutrik Powercon IN/OUT
●Data Connector: 3-pin XLR IN/OUT
●Fuse: F10A/250V
●Dimensions: 1080 x 130 x 130 mm (LxWxH) (incl. brackets)
●Weight: 6,2 kg
Note: Knowledge of DMX is required to fully utilize this unit.
Optional accessories
30713 Multibracket for Sunstrip
D7039 Case for 12x Sunstrip Active
D7240 Case for 8x Sunstrip Active (Premium Line)
D7510 Case for 8x Sunstrip Active
Frontside
Fig. 01
01) 10 x 110V/50W GU10 (Ordercode: SPHK498)
02) Adjustment screw
03) Mounting bracket

8
Ordercode: 30751
Sunstrip Active MKII 110V
Backside
Fig. 02
04) 3-pin DMX signal connector OUT
05) Neutrik Powercon Thru (Grey, Max 20A)
06) Ground/Earth connection
07) 4-digit LED display + menu buttons
08) Fuse 6A/250V
09) Powerswitch ON/OFF
10) Neutrik Powercon IN (Blue, Max 20A)
11) 3-pin DMX signal connector IN
Installation
Remove all packing materials from the Sunstrip Active MKII 110V. Check if all foam and plastic padding is
removed. Connect all cables.
Do not supply power before the whole system is set up and connected properly.
Always disconnect from electric mains power supply before cleaning or servicing.
Damages caused by non-observance are not subject to warranty.

9
Ordercode: 30751
Sunstrip Active MKII 110V
Installing the Lamp
The Showtec Sunstrip Active MKII 110V uses a 110V/50W GU10 bulb (Ordercode: SPHK498) as
manufactured by all popular manufacturers. Use only the appropriate lamp for your unit.
Note that, product versions that use other lamps, may be offered in the future. Check your product
specification label for information.
Always disconnect from electric mains power supply before changing lamps.
The lamp has to be replaced when it is damaged or deformed due to the heat.
Do not install lamps with a higher wattage! Lamps with a higher wattage generate temperatures the
device was not designed for.
Damages caused by non-observance are not subject to warranty.
Procedure
01) Loosen the 4 screws on the front of the housing.
02) Gently remove the metal housing (Fig. 05).
03) Read lamp instructions. Do not touch the lamp bulb glass.
04) Push and turn the lamp counter clockwise and remove the lamp (Fig. 06).
05) Oil on hands shortens the lamp life. (If you touch the bulb glass, wipe off the glass with a clean, lint-
free towel and rubbing alcohol).
06) Insert the lap pins into the small holes in the lamp socket.
Push and turn clockwise to install the lamp (Fig. 07).
07) Put the metal housing back and fasten the screws snugly (Fig. 08).
Fig.05
Fig.06
Fig.07
Fig.08

10
Ordercode: 30751
Sunstrip Active MKII 110V
Set Up and Operation
Follow the directions below, as they pertain to your preferred operation mode.
Before plugging the unit in, always make sure that the power supply matches the product specification
voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa.
Connect the device to the main power supply.
Control Modes
There are 2 modes:
●Chase mode
●DMX-512 (1CH, 2CH, 5CH or 10CH)
One Sunstrip Active (Chase mode)
01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) When the Sunstrip Active is not connected with a DMX cable, it functions as a stand-alone device.
Please see page 13 for more information about the Chase mode.
Multiple Sunstrips Active (DMX Control)
01) Fasten the effect light to a firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Use a 3-pin XLR cable to connect the Sunstrips Active and other devices.
04) Link the units as shown in Fig. 09. Connect the first unit's DMX "out" socket with the second unit's "in"
socket, using a DMX-signal cable. Repeat this process to link the second and third units.
05) Supply electric power: Plug electric mains power cords into each unit's Neutrik Powercon, then plug
the other end of the mains power cord into proper electric power supply sockets, starting with the
first unit. Do not supply power before the whole system is set up and connected properly.

11
Ordercode: 30751
Sunstrip Active MKII 110V
Multiple Sunstrips Active DMX Set Up
Fig. 09
Note : Link all cables before connecting electric power
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to
run synchronized shows of two or more fixtures set to a master/slave operating mode. The combined
number of channels required by all the fixtures on a serial data link determines the number of fixtures the
data link can support.
Important:
Fixtures on a serial data link must be daisy-chained in a single line. To comply with the
EIA-485 standard, no more than 30 devices should be connected on one data link.
Connecting more than 30 fixtures on one serial data link without the use of a DMX optically
isolated splitter may result in deterioration of the digital DMX signal.
Maximum recommended DMX data link distance: 100 meters
Maximum recommended number of fixtures on a DMX data link: 30 fixtures
Maximum recommended number of fixtures on a power link @ 110V: 3 fixtures
Data Cabling
To link fixtures together, you must obtain data cables. You can purchase DAP Audio certified DMX cables
directly from a dealer/distributor or construct your own cable. If you choose to create your own cable,
please use data-grade cables that can carry a high quality signal and are less prone to electromagnetic
interference.
DAP Audio DMX Data Cables
●DAP Audio Basic microphone cable for allround use. bal. XLR/M 3-pin > XLR/F 3-pin. Ordercode
FL01150 (1,5 m), FL013 (3 m), FL016 (6 m), FL0110 (10 m), FL0115 (15 m), FL0120 (20 m).
●DAP Audio X-type data cable XLR/M 3-pin > XLR/F 3-pin. Ordercode FLX0175 (0,75 m),
FLX01150 (1,5 m), FLX013 (3 m), FLX016 (6 m), FLX0110 (10 m).
●DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL71150 (1,5 m), FL713 (3 m), FL716 (6 m), FL7110 (10 m).
●DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL7275 (0,75 m), FL72150 (1,5 m), FL723 (3 m), FL726 (6 m), FL7210 (10 m).
●DAP Audio 110 Ohm cable with digital signal transmission. Ordercode FL0975 (0,75 m),
FL09150 (1,5 m), FL093 (3 m), FL096 (6 m), FL0910 (10 m), FL0915 (15 m), FL0920 (20 m).
●DAP Audio data cable FL08 DMX/AES-EBU, XLR/M 5-pin > XLR/F 5-pin.Ordercode FL08150 (1,5 m),
FL083 (3 m), FL086 (6 m), FL0810 (10 m), FL0820 (20 m).
●DAP Audio DMX adapter: 5-pin/3-pin. Ordercode FLA29.
●DAP Audio DMX adapter: 3-pin/5-pin. Ordercode FLA30.
The Sunstrip Active MKII 110V can be operated with a controller in control mode or without the controller
in stand-alone mode.

12
Ordercode: 30751
Sunstrip Active MKII 110V
Control Panel
A) LED display
B) Mode button
C) Menu button
D) Up button
E) Down button
Fig. 04
Control Mode
The fixtures are individually addressed on a data-link and connected to the controller.
The fixtures respond to the DMX signal from the controller. (When you select the DMX address and save it,
the controller will display the saved DMX address, next time.)
DMX Addressing
The control panel on the back side of the device allows you to assign DMX fixture addresses, which is the
first channel with which the Sunstrip will respond to the controller.
Please note, when you use the controller, the unit has 10 channels.
When using multiple Sunstrips, make sure you set the DMX addresses right.
Therefore, the DMX address of the first Sunstrip should be 1(A001); the DMX address of the second Sunstrip
should be 1+10=11 (A011); the DMX address of the third Sunstrip should be 11+10=21 (A021), etc. Please,
be sure that you do not have any overlapping channels in order to control each Sunstrip correctly. If two
or more Sunstrips are addressed similarly, they will work similarly.
Controlling:
After having addressed all Sunstrips, you may now start operating these via your lighting controller.
Note: After switching on, the Sunstrip will automatically detect whether DMX 512 data is received or not.
If there is no data received at the DMX-input, the “LED“ on the control panel will not flash.
If not, the problem may be:
●The XLR cable from the controller is not connected with the input of the Sunstrip.
●The controller is switched off or defective, the cable or connector is detective, or the signal wires are
swapped in the input connector.
Note: It is necessary to insert an XLR termination plug (with 120 Ohm) in the last fixture in order to ensure
proper transmission on the DMX data link.
Display Off after 10 seconds
When no button is pressed for 10 seconds, the display will turn off.
To light up the display, you have to press the Mode, Menu, Up or Down button.
Once you have pressed the button, the display will light up.

13
Ordercode: 30751
Sunstrip Active MKII 110V
Menu Overview
DMX Mode
Chase Mode
Main Menu Options
DMX Mode
DMX address
DMX configuration
Chase Mode
Chase program
Chase direction
Chase speed
Chase dimmer
The Sunstrip Active MKII 110V will show Showtec at start-up !
The text will remain in the display for 30 seconds.
1. DMX Mode
With this mode you can set the DMX address and choose a DMX configuration.
1.1 DMX address
01) Press and hold the Mode button for 5 seconds until the display starts blinking.
02) Press the Mode or Menu button, until the display shows .
03) You can choose 512 different DMX addresses.
04) Press the Up/Down buttons to select the required address from .
Press and hold down the Up and Down buttons and the device immediately returns
to its default address A001.
Note: To change this option, the display has to blink.

14
Ordercode: 30751
Sunstrip Active MKII 110V
1.2 DMX configuration
01) Press the Menu button (in DMX Mode), until the display shows .
02) You can choose 4 different DMX configurations.
03) Press the Up/Down buttons to select the required DMX configuration.
1 DMX channel
2 DMX channels
5 DMX channels
10 DMX channels
Note: To change this option, the display has to blink.
2. Chase Mode
With this mode you can choose a built-in chase program, set the direction of the chase, set the speed of
the chase and set the dimmer of the chase.
2.1 Chase program
01) To activate the chase programs, you have to set the dimmer between .
02) Press and hold the Mode button for 5 seconds until the display starts blinking.
03) Press the Mode or Menu button, until the display shows .
04) You can choose 16 different built-in programs, auto or full.
05) Press the Up/Down buttons to select the required built-in program from .
06) If you choose program, the device will start with its built-in chases 1-16 in sequence.
07) If you choose , all 10 LEDs will light up and remain On at 100% output.
Note: To change this option, the display has to blink.
2.2 Chase direction
01) Press the Menu button (in Chase Mode), until the display shows .
02) You can choose or .
03) Press the Up/Down buttons to select the required direction.
04) If you choose , the chase will start in the regular direction.
05) If you choose , the chase will start in the reverse direction.
Note: To change this option, the display has to blink.
2.3 Chase speed
01) Press the Menu button (in Chase Mode), until the display shows .
02) Press the Up/Down buttons to select the required speed.
03) Set the speed between .
Note: To change this option, the display has to blink.
2.4 Chase dimmer
01) Press the Menu button (in Chase Mode), until the display shows .
02) Press the Up/Down buttons to select the required light intensity.
03) Set the intensity between .
Note: To change this option, the display has to blink.

15
Ordercode: 30751
Sunstrip Active MKII 110V
Edit welcome text
The default text is Showtec, with this function you can create your own welcome text.
01) Press and hold the Mode button for 5 seconds, until the display starts blinking.
02) Now press and hold the Mode button, while pressing the following buttons in sequence:
Up,Up,Down,Down,Up, Down to enter the Edit mode.
03) Press and hold the Up button for 2 seconds to select the next character you want to edit.
04) If you have made an error and want to change the previous character, press and hold the Down
button for 2 seconds to select the previous character.
05) Press the Up/Down button to select a certain character. Repeat step 3-5 to edit all characters.
06) The text can hold a maximum of 23 characters.
07) When you have completed your welcome text, press the Up/Down buttons simultaneously, the
display will show the created text.
08) Press the Mode button for 5 seconds to exit the Edit mode.
Available characters
DMX Channels
1 DMX channel
Channel 1 –Dimmer intensity (All LEDs)
0-255
Gradual adjustment, from dark to brightest 0-100%
2 DMX channels
Channel 1 –Dimmer intensity section 1
0-255
Gradual adjustment, from dark to brightest 0-100%
Channel 2 –Dimmer intensity section 2
0-255
Gradual adjustment, from dark to brightest 0-100%

16
Ordercode: 30751
Sunstrip Active MKII 110V
5 DMX channels
Channel 1 –Dimmer intensity section 1
0-255
Gradual adjustment, from dark to brightest 0-100%
Channel 2 –Dimmer intensity section 2
0-255
Gradual adjustment, from dark to brightest 0-100%
Channel 3 –Dimmer intensity section 3
0-255
Gradual adjustment, from dark to brightest 0-100%
Channel 4 –Dimmer intensity section 4
0-255
Gradual adjustment, from dark to brightest 0-100%
Channel 5 –Dimmer intensity section 5
0-255
Gradual adjustment, from dark to brightest 0-100%

17
Ordercode: 30751
Sunstrip Active MKII 110V
10 DMX channels
Channel 1 –Dimmer intensity LED 1
0-255
Gradual adjustment, from dark to brightest 0-100%
Channel 2 –Dimmer intensity LED 2
0-255
Gradual adjustment, from dark to brightest 0-100%
Channel 3 –Dimmer intensity LED 3
0-255
Gradual adjustment, from dark to brightest 0-100%
Channel 4 –Dimmer intensity LED 4
0-255
Gradual adjustment, from dark to brightest 0-100%
Channel 5 –Dimmer intensity LED 5
0-255
Gradual adjustment, from dark to brightest 0-100%
Channel 6 –Dimmer intensity LED 6
0-255
Gradual adjustment, from dark to brightest 0-100%
Channel 7 –Dimmer intensity LED 7
0-255
Gradual adjustment, from dark to brightest 0-100%
Channel 8 –Dimmer intensity LED 8
0-255
Gradual adjustment, from dark to brightest 0-100%
Channel 9 –Dimmer intensity LED 9
0-255
Gradual adjustment, from dark to brightest 0-100%
Channel 10 –Dimmer intensity LED 10
0-255
Gradual adjustment, from dark to brightest 0-100%
Maintenance
The Sunstrip Active MKII 110V requires almost no maintenance. However, you should keep the unit clean.
Otherwise, the fixture’s light-output will be significantly reduced. Disconnect the mains power supply, and
then wipe the cover with a damp cloth. Do not immerse in liquid. Wipe lens clean with glass cleaner and
a soft cloth. Do not use alcohol or solvents.
The front lens will require weekly cleaning, as smoke-fluid tends to build up residues, reducing the light-
output very quickly.
Keep connections clean. Disconnect electric power, and then wipe the DMX connections with a damp
cloth. Make sure connections are thoroughly dry before linking equipment or supplying electric power.
The operator has to make sure that safety-related and machine-technical installations are to be
inspected by an expert after every year in the course of an acceptance test.
The operator has to make sure that safety-related and machine-technical installations are to be
inspected by a skilled person once a year.
The following points have to be considered during the inspection:
01) All screws used for installing the device or parts of the device have to be tightly connected and
must not be corroded.
02) There may not be any deformations on housings, fixations and installation spots.
03) Mechanically moving parts like axles, eyes and others may not show any traces of wearing.
04) The electric power supply cables must not show any damages or material fatigue.

18
Ordercode: 30751
Sunstrip Active MKII 110V
Changing the Lamp
01) Disconnect mains power supply. Allow the fixture to cool for at least 15 minutes before handling and
replacing lamp.
02) Read lamp instructions.
03) Follow directions for installing a new lamp page 9.
Replacing the Fuse
Power surges, short-circuit or inappropriate electrical power supply may cause a fuse to burn out.
If the fuse burns out, the product will not function whatsoever. If this happens, follow the directions below:
01) Unplug the unit from electric power source.
02) Insert a flat-headed screwdriver into a slot in the fuse cover. Turn the screwdriver to the left, at the
same time gently push a bit (Turn and Push). The fuse will come out.
03) Remove the used fuse. If brown or unclear, it is burned out.
04) Insert the replacement fuse into the holder. Reinsert the fuse cover. Be sure to use a fuse of the
same type and specification. See the product specification label for details.
Troubleshooting
This troubleshooting guide is meant to help solve simple problems.
If a problem occurs, carry out the steps below in sequence until a solution is found. Once the unit
operates properly, do not carry out following steps.
No Light
If the light effect does not operate properly, refer servicing to a technician.
Suspect three potential problem areas as: the power supply, the lamp, the fuse.
01) Power supply. Check that the unit is plugged into an appropriate power supply.
02) The lamp. Replace the old lamp with a new one with the same specifications. See page 9 for
replacing the lamp.
03) The fuse. Replace the fuse. See page 18 for replacing the fuse.
04) If all of the above appears to be O.K., plug the unit in again.
05) If you are unable to determine the cause of the problem, do not open the Sunstrip Active, as this
may damage the unit and the warranty will become void.
06) Return the device to your Showtec dealer.
No Response to DMX
Suspect the DMX cable or connectors, a controller malfunction, a light effect DMX card malfunction.
01) Check the DMX setting. Make sure that DMX addresses are correct.
02) Check the DMX cable: Unplug the unit; change the DMX cable; then reconnect to electrical power.
Try your DMX control again.
03) Determine whether the controller or light effect is at fault. Does the controller operate properly with
other DMX products? If not, take the controller in for repair. If so, take the DMX cable and the light
effect to a qualified technician.

19
Ordercode: 30751
Sunstrip Active MKII 110V
Problem
Probable cause(s)
Solution
One or more
fixtures do not
function at all
No power to the fixture
•Check if power is switched on and
cables are plugged in
Primary fuse blown
•Replace fuse
Fixtures reset
correctly, but all
respond erratically
or not at all to the
controller
The controller is not connected.
•Connect controller.
3-pin XLR Out of the controller
does not match XLR Out of the first
fixture on the link (i.e. signal is
reversed)
•Install a phase reversing cable
between the controller and the
first fixture on the link
Fixtures reset
correctly, but
some respond
erratically or not at
all to the controller
Poor data quality
•Check data quality. If much lower
than 100 percent, the problem
may be a bad data link
connection, poor quality or
broken cables, missing termination
plug, or a defective fixture
disturbing the link
Bad data link connection
•Inspect connections and cables.
Correct poor connections. Repair
or replace damaged cables
Data link not terminated with 120
Ohm termination plug
•Insert termination plug in output
jack of the last fixture on the link
Incorrect addressing of the fixtures
•Check address setting
One of the fixtures is defective and
disturbs data transmission on the
link
•Bypass one fixture at a time until
normal operation is restored:
unplug both connectors and
connect them directly together.
•Have the defective fixture
serviced by a qualified technician
3-pin XLR Out on the fixtures does
not match (pins 2 and 3 reversed)
•Install a phase-reversing cable
between the fixtures or swap pin 2
and 3 in the fixture that behaves
erratically
No light or lamp
cuts out
intermittently
Fixture is too hot
•Allow the fixture to cool down
•Clean the fan
•Make sure air vents in control
panel and the front lens are not
blocked
•Turn up the air conditioning
Lamp damaged
•Disconnect the fixture and
replace the lamp
The power supply settings do not
match local AC voltage and
frequency
•Disconnect fixture. Check settings
and correct if necessary