Show Tec Media Panel 50 User manual

Media Panel 50
Highlite International B.V. –Vestastraat 2 –6468 EX –Kerkrade –the Netherlands
Product code: 33300
USER MANUAL
ENGLISH
V1

1
Media Panel 50
Product code: 33300
Preface
Thank you for purchasing this Showtec product.
The purpose of this user manual is to provide instructions for the correct and safe use of this product.
Keep the user manual for future reference as it is an integral part of the product. The user manual shall be
stored at an easily accessible location.
This user manual contains information concerning:
●Safety instructions
●Intended and non-intended use of the device
●Installation and operation of the device
●Maintenance procedures
●Troubleshooting
●Transport, storage and disposal of the device
Non-observance of the instructions in this user manual may result in serious injuries and damage of
property.
©2021 Showtec. All rights reserved.
No part of this document may be copied, published or otherwise reproduced without the prior written
consent of Highlite International.
Design and product specifications are subject to change without prior notice.
For the latest version of this document, please visit our website www.highlite.com or contact us at
[e-mail].
Highlite International and its authorized service providers are not liable for any injury, damage, direct or
indirect loss, consequential or economic loss or any other loss arising from the use of, or inability to use or
reliance on the information contained in this document.

2
Media Panel 50
Product code: 33300
Table of contents
1. Introduction..........................................................................................................................................................3
Before Using the Product ..................................................................................................................................3
Intended Use .......................................................................................................................................................3
Product Lifespan.................................................................................................................................................3
LEDs Lifespan .......................................................................................................................................................3
Text Conventions ................................................................................................................................................4
Symbols and Signal Words................................................................................................................................4
Symbols on the Information Label ..................................................................................................................5
2. Safety ....................................................................................................................................................................6
Warnings and Safety Instructions ....................................................................................................................6
Requirements for the User.................................................................................................................................8
3. Description of the Device...................................................................................................................................9
Front View ............................................................................................................................................................9
Back View ..........................................................................................................................................................10
Product Specifications ....................................................................................................................................11
Optional Accessories.......................................................................................................................................12
Dimensions.........................................................................................................................................................12
4. Installation ..........................................................................................................................................................13
Safety Instructions for Installation ..................................................................................................................13
Personal Protective Equipment .....................................................................................................................13
Installation Site Requirements ........................................................................................................................13
Rigging ...............................................................................................................................................................14
Angle Adjustment.......................................................................................................................................16
Barndoor Installation ..................................................................................................................................17
Free-standing Bracket Installation ...........................................................................................................18
Connecting to Power Supply.........................................................................................................................19
5. Setup ...................................................................................................................................................................20
Warnings and Precautions .............................................................................................................................20
Stand-alone Setup ...........................................................................................................................................20
6. Operation ...........................................................................................................................................................21
Safety Instructions for Operation...................................................................................................................21
Control Mode....................................................................................................................................................21
Control Panel ....................................................................................................................................................22
Start-up...............................................................................................................................................................22
Dimmer .........................................................................................................................................................22
7. Troubleshooting .................................................................................................................................................23
8. Maintenance .....................................................................................................................................................24
Preventive Maintenance................................................................................................................................24
Basic Cleaning Instructions .......................................................................................................................24
Corrective Maintenance................................................................................................................................24
9. Deinstallation, Transportation and Storage ....................................................................................................25
Instructions for Deinstallation..........................................................................................................................25
Instructions for Transportation ........................................................................................................................25
Storage...............................................................................................................................................................25
10. Disposal ..............................................................................................................................................................25
11. Approval.............................................................................................................................................................25

3
Media Panel 50
Product code: 33300
1. Introduction
Before Using the Product
Important
Read and follow the instructions in this user manual before installing, operating or
servicing this product.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual.
After unpacking, check the contents of the box. If any parts are missing or damaged, contact your
Highlite International dealer.
Your shipment includes:
●Showtec Media Panel 50
●Schuko to IEC power cable (1,5 m)
●Four-blade barndoor
●Spigot adapter
●Power adapter
●User manual
Fig. 01
Intended Use
This device is intended for professional use as an indoor spot. It is suitable only for indoor installation.
This device is not suitable for households and for general lighting.
Any other use, not mentioned under intended use, is regarded as non-intended and incorrect use.
Product Lifespan
This device is not designed for permanent operation. Disconnect the device from the electrical power
supply when the device is not in operation. This will reduce the wear and will improve the device’s
lifespan.
LEDs Lifespan
The light output of the LEDs gradually decreases over time (lumen depreciation). High operating
temperatures contribute to this process. You can extend the lifespan of the LEDs by providing adequate
ventilation and operating the LEDs at the lowest possible brightness.

4
Media Panel 50
Product code: 33300
Text Conventions
Throughout the user manual the following text conventions are used:
●Buttons: All buttons are in bold lettering, for example “Press the UP/DOWN buttons”
●References: References to chapters and parts of the device are in bold lettering, for example:
“Refer to 2. Safety”, “turn the adjustment screw (02)”
●0–255: Defines a range of values
●Notes: Note: (in bold lettering) is followed by useful information or tips
Symbols and Signal Words
Safety notes and warnings are indicated throughout the user manual by safety signs.
Always follow the instructions provided in this user manual.
DANGER
Indicates an imminently hazardous situation which, if not avoided, will result in
death or serious injury.
WARNING
Indicates a potentially hazardous situation which, if not avoided, could result in
death or serious injury.
CAUTION
Indicates a potentially hazardous situation, which, if not avoided, may result in
minor or moderate injury.
Attention
Indicates important information for the correct operation and use of the
product.
Important
Read and observe the instructions in this document.
Electrical hazard
Provides important information about the disposal of this product.

5
Media Panel 50
Product code: 33300
Symbols on the Information Label
This product is provided with an information label. The information label is located on the backside of the
device.
The information label contains the following symbols:
This device shall not be treated as household waste.
This device falls under IEC protection class II.
Replace any cracked protective shield.
Minimum distance from lighted objects.

6
Media Panel 50
Product code: 33300
2. Safety
Important
Read and follow the instructions in this user manual before installing, operating or
servicing this product.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual.
Warnings and Safety Instructions
DANGER
Danger for children
For adult use only. The device must be installed beyond the reach of children.
●Do not leave various parts of the packaging (plastic bags, polystyrene foam, nails, etc.) within
children’s reach. Packaging material is a potential source of danger for children.
DANGER
Electric shock caused by short-circuit
This device falls under IEC protection class II.
●Make sure that the device is electrically connected to ground (earth). Connect the device only to a
socket-outlet with ground (earth) connection.
●Do not cover the ground (earth) connection.
●Do not bypass the thermostatic switch or fuses.
●For replacement use fuses of the same type and rating only.
●Do not let the power cable come into contact with other cables. Handle the power cable and all
connections with the mains with caution.
●Do not modify, bend, mechanically strain, put pressure on, pull or heat up the power cable.
●Make sure that the power cable is not crimped or damaged. Examine the power cable periodically
for any defects.
●Do not immerse the device in water or other liquids. Do not install the device in a location where
flooding may occur.
●Do not use the device during thunderstorms. Disconnect the device from the electrical power supply
immediately.
Attention
Power supply
Before connecting the device to the power supply, make sure that the current, voltage and frequency
match the input voltage, current and frequency specified on the information label on the device.

7
Media Panel 50
Product code: 33300
Attention
General safety
●Do not connect the device to a dimmer pack.
●Do not switch the device on and off in short intervals. This decreases the device’s life.
●Do not shake the device. Avoid brute force when installing or operating the device.
●Change the lens or the LEDs if they are visibly damaged to such an extent that their effectiveness is
impaired, for example by cracks or deep scratches. Contact your Highlite International dealer for
more information, as servicing can be performed only by instructed or skilled persons.
●If the device is dropped or struck, disconnect the device from the electrical power supply
immediately.
●If the device is exposed to extreme temperature variations (e.g. after transportation), do not switch it
on immediately. Let the device reach room temperature before switching it on, otherwise it may be
damaged by the formed condensation.
●If the device fails to work properly, discontinue the use immediately.
Attention
For professional use only
This device shall be used only for the purposes it is designed for.
This device is designed to be used as an indoor spot. Any incorrect use may lead to hazardous situations
and result in injuries and material damage.
●This device is not suitable for households and for general lighting.
●This device is not designed for permanent operation.
●This device contains a non-user-replaceable light source.
●This device does not contain user-serviceable parts. Unauthorized modifications to the device will
render the warranty void. Such modifications may result in injuries and material damage.
Attention
Before each use, examine the device visually for any defects.
Make sure that:
●All screws used for installing the device or parts of the device are tightly fastened and are not
corroded.
●The safety devices are not damaged.
●There are no deformations on housings, fixations and installation points.
●The lens is not cracked or damaged.
●The power cables are not damaged and do not show any material fatigue.
Attention
Do not expose the device to conditions that exceed the rated IP class conditions.
This device is IP20 rated. IP (Ingress Protection) 20 class provides protection against solid objects greater
than 12 mm, such as fingers, and no protection against harmful ingress of water.

8
Media Panel 50
Product code: 33300
Requirements for the User
This product may be used by ordinary persons. Maintenance may be carried by ordinary persons.
Installation and service shall be carried out only by instructed or skilled persons. Contact your Highlite
dealer for more information.
Instructed persons have been instructed and trained by a skilled person, or are supervised by a skilled
person, for specific tasks and work activities associated with the installation, service and maintenance of
this product, so that they can identify risks and take precautions to avoid them.
Skilled persons have training or experience, which enables them to recognize risks and to avoid hazards
associated with the installation, service and maintenance of this product.
Ordinary persons are all persons other than instructed persons and skilled persons. Ordinary persons
include not only users of the product but also any other persons that may have access to the device or
who may be in the vicinity of the device.

9
Media Panel 50
Product code: 33300
3. Description of the Device
The Media Panel 50 a bright 50 watt Daylight White Video LED Panel suited for various studio and video
applications. A V-Mount Battery Holder is optional for mobile use (ordercode 33310). This optional
accessory requires a 24V battery life pack.
Front View
Fig. 02
01) Adjustment screw
02) Mounting bracket
03) Barndoor
04) 196x 0,5 W White LED

10
Media Panel 50
Product code: 33300
Back View
Fig. 03
05) LED Display
06) Dimmer control
07) ON/OFF
08) 24 V DC power adapter IN

11
Media Panel 50
Product code: 33300
Product Specifications
Model:
Media Panel 50
Electrical:
Input voltage:
24 V DC
Input current:
1 A
Power consumption:
50 W
Physical:
Dimensions:
376 x 273 x 55 mm (LxWxH)
Weight:
1,8 kg
Optics:
Light source:
196x 0,5 W White LED
Dimmer:
0–100 %
CCT
5000 K
CRI
98
Lumen Total
4000 lm
Lux @ 2m
511 lx
Lux @ 3m
227 lx
Beam Angle Circular
87 °
Field Angle Circular
143 °
Operation and control:
Control:
Manual
Control panel:
LED display
Connections:
Power connections:
IEC cable connected to 24 V DC adapter
AC power adapter:
Input voltage:
100–240 V AC, 50/60 Hz
Input current:
2,0 A
Output voltage:
24 V DC
Output current:
2,5 A
Construction:
Housing:
Metal
Color:
Dark Gray
IP rating:
IP20
Cooling:
Convection
16mm Spigot
Thermal:
Maximum ambient temperature ta:
45 °C
Minimum Operating Temperature
0 °C
Maximum housing temperature tc:
65 °C
Minimum distance:
Minimum distance from flammable surfaces:
0,3 m
Minimum distance to lighted object:
0,8 m

12
Media Panel 50
Product code: 33300
Optional Accessories
The Media Panel is delivered with accessories. You can additionally purchase the following accessory:
Product code: 33310 (Showtec A V-Mount Battery Holder is optional for mobile use)
Dimensions
Fig. 04

13
Media Panel 50
Product code: 33300
4. Installation
Safety Instructions for Installation
WARNING
Incorrect installation can cause serious injuries and damage of property.
If trussing systems are used, installation must be carried out only by instructed or skilled persons.
Follow all applicable European, national and local safety regulations concerning rigging and trussing.
Personal Protective Equipment
During installation and rigging wear personal protective equipment in compliance with the national and
site-specific regulations.
Installation Site Requirements
●The device can be used only indoors.
●The device can be mounted to a truss or other rigging structure in any orientation.
●The minimum distance to other objects must be bigger than 0,3 m.
●The minimum distance between the light output and the illuminated surface must be bigger than
0,8 m.
●The maximum ambient temperature ta = 40 °C must never be exceeded.
●The relative humidity must not exceed 50 % with an ambient temperature of 40 °C.

14
Media Panel 50
Product code: 33300
Rigging
The device can be positioned on a flat surface or mounted to a truss or other rigging structure in any
orientation. Make sure that all loads are within the pre-determined limits of the supporting structure.
Fig. 05
CAUTION
Restrict the access under the work area during rigging and/or derigging.

15
Media Panel 50
Product code: 33300
To mount the device, follow the steps below:
01) Use a clamp to attach the device to the supporting structure, as shown in Fig. 05. Make sure that the
device cannot move freely.
02) Secure the device with a secondary suspension, for example a safety cable. Make sure that the
secondary suspension can hold 10 times the weight of the device. If possible, the secondary
suspension should be attached to a supporting structure independent of the primary suspension. Put
the safety cable through the mounting bracket (02), as shown in Fig. 06.
Fig. 06

16
Media Panel 50
Product code: 33300
Angle Adjustment
You can adjust the angle of the device with the adjustment screw (01).
01) Turn the adjustment screw (01) counterclockwise to release it.
02) Tilt the device to the desired angle (see Fig. 07).
03) Turn the adjustment screw (01) clockwise to tighten it. Make sure that the device cannot move freely
after the adjustment screw (01) is tightened.
Fig. 07

17
Media Panel 50
Product code: 33300
Barndoor Installation
The accessory frame is equipped with a spring-loaded clip. This prevents the barndoor from falling out.
Install the barndoor frame (see Fig. 08).
Hold the spring-loaded clip and pull it upwards on the top of the device and pull it downwards at
the bottom (see Fig. 09).
Release each spring-loaded clip once it is over the designated mounting hole at the bottom and the
top of the device (see Fig. 10).
Fig. 08
Fig. 09
Fig. 10

18
Media Panel 50
Product code: 33300
Free-standing Bracket Installation
Put the free-standing bracket on the Media Panel.
Install all elements as shown in Fig. 11.
Tighten the screws.
Fig. 11

19
Media Panel 50
Product code: 33300
Connecting to Power Supply
Attention
Power supply
This device falls under IEC protection class II. This device shall be connected to an external power supply.
This device is delivered with an AC power adapter. Before connecting the AC power adapter to the
socket-outlet, make sure that the power supply matches the Input voltage specified on the information
label on the AC power adapter.
To turn the device on, follow the steps below:
Connect the AC power adapter to the device. Use only the AC power adapter delivered with the
device.
Connect the AC power adapter to the socket-outlet.