showhome ZW31T User manual

Federal Communications Commission (FCC) Statement
FCC Caution: Anychangesor modifications not expressly approved bythe partyresponsible for
compliancecould void the user sauthoritytooperatethisequipment.
This devicecomplieswithPart 15 of the FCC Rules. Operation is subject tothe following two
conditions: (1) This devicemaynot causeharmful interference, and (2) thisdevicemust accept any
interferencereceived, including interferencethat maycauseundesired operation.
NOTE: This equipment hasbeen tested and found tocomplywiththe limitsfor aClass B digital device,
pursuant toPart 15 of the FCC Rules. Theselimitsaredesigned toprovide reasonable protection
against harmful interferencein aresidential installation. This equipment generates, usesand can
radiateradio frequency energyand, if not installed and used in accordancewiththe instructions,
maycausharmful interferencetoradio communications.However, thereis no guarantee that
interferencewill not occur in aparticular installation. If thisequipment doescauseharmful interference
toradio or television reception, whichcan be determined byturning the equipment off and on,
the user is encouraged totrytocorrect the interferencebyone or moreof the following measures:
Reorient or relocatethe receiving antenna.Increasethe separation between the equipment and
receiver.Connect the equipment intoan outlet on acircuit different fromthat towhichthe receiver
isconnected.Consult the dealer or an experienced radio/TV technician for help.This equipment
should be installed and operated withminimumdistance20cmbetween the radiator and your body.
IC Caution:
ThisdevicecomplieswithIndustryCanada licence-exempt RSS standard(s). Operation is subject
tothe following twoconditions: (1) thisdevicemaynot causeinterference, and (2) thisdevicemust
accept anyinterference, including interferencethat maycauseundesired
operation of the device.
DECLARATION DE CONFORMITE D'INDUSTRIE CANADA
Cepériphérique a ététestéet reconnu conformeauxlimitesspécifiéesdansRSS-210.
Son utilisation est soumise auxdeuxconditions suivantes:
(1) il ne doit pasprovoquer d'interférencesgênanteset
(2) il doit tolérer les interférencesre.ues, notamment cellessusceptibles d'en perturber le fonctionnement.
ZW31T Smart Dimmer Manual
Smart Dimmer
WARRANTY
ShowHomeProductswarrantsthisproduct tobe free frommanufacturing defectsfor
a period of twoyearsfromthe originaldateof consumerpurchase. Thiswarrantyislimited
to the repair orreplacement of thisproduct onlyand doesnot extend toconsequentialor
incidentaldamage tootherproductsthat maybe used withthisproduct.
Thiswarrantyisinlieu of all otherwarranties, expressed orimplied. Somestatesdo not
allowlimitationson howlong an implied warrantylastsorpermit the exclusion orlimitation
of incidentalorconsequentialdamage, sothe abovelimitationsmaynot applytoyou.
Thiswarrantygivesyou specificrights, and you mayalsohaveotherrightswhichvaryfrom
statetostate. if the unit shouldprovedefectivewithinthe warrantyperiod.
SPECIFICATIONSWARNING
RISK OFFIRE
Model:ZW31T
RISK OFELECTRICALSHOCK
Power: 120 VAC, 60 Hz.
RISK OFBURNS
Signal (Frequency): 908.42 MHZ.
CONTROLLING APPLIANCES:
Dimension(L*W*H):115*71*42(mm)
EXERCISE EXTREMECAUTION WHEN USING Z-WAVE DEVICES TO CONTROL
MaximumLoads: 500W, 2-gang 400W or 3-gang
APPLIANCES. OPERATION OFTHEZ-WAVE DEVICEMAY BE IN ADIFFERENT
300W incandescent, 150W CFL/LED
ROOMTHAN THECONTROLLED APPLIANCE, ALSO ANUNINTENTIONALACTIVATION
Range: Upto100 feet line of sight between the
MAY OCCUR IFTHEWRONG BUTTON ON THEREMOTEISPRESSED. Z-WAVE DEVICES
Wireless Controller and the closest Z-Wave
MAY AUTOMATICALLYBE POWERED ON DUETO TIMED EVENTPROGRAMMING.
receiver module.
DEPENDING UPON THEAPPLIANCE, THESE UNATTENDED OR UNINTENTIONAL
Operating TemperatureRange: 32-104°F(0-40°C)
OPERATIONSCOULD POSSIBLYRESULTIN AHAZARDOUSCONDITION. FOR THESE
For indoor useonly.
REASONS, WE RECOMMEND DO NOTRETURN THISPRODUCTTO THESTORE
Specifications subject tochange without notice
THEFOLLOWING:
due tocontinuing product improvement
DO NOTUSE Z-WAVE DEVICES TO CONTROLELECTRIC HEATERSOR ANYOTHER
IMPORTANT!
APPLIANCES WHICH MAY PRESENTAHAZARDOUSCONDITION DUETO UNATTENDED OR
The fixturecontrolled bythe Z-WaveIn-wall Smart
UNINTENTIONALOR AUTOMATIC POWER ON CONTROL.
Dimmermust not exceed 600 watts(Incandescent);
150WdimmableCFL/LED. The Dimmeris
designed onlyforusewithpermanentlyinstalled fixtures.
Website:www.ishowlights.com

1. Getting ToKnowYour NewZ-WaveDevice
•Dimming light manuallyor remotelyviathe Z-Wavecontroller
•Can be Included inmultipleGroupsand Scenes
•Compatiblewithall incandescent and CFL/ LEDbulbs
•Z-WaveCertified for simplepairing and integrated homeautomation
•ScrewTerminal Installation —requireswiring connectionsfor Line (Hot), Load, Neutral.
WARNING —SHOCK HAZARD
TurnOFF the power tothe branchcircuit for the dimmer and lighting fixtureat the servicepanel. All wiring
connectionsmust be made withthe power OFF toavoidpersonal injury and/or damage tothe switch.
A. UpPushbutton
B. DownPushbutton
C. Nutral (White) - Nutral in
D. Line (Black) - Line in
E. Load (Black)
Singleswitchwiring
1. Shut off power tothe circuit at circuit breaker or fusebox.
IMPORTANT! Verify power is OFF toswitchboxbeforecontinuing.
2. Removewall plate.
3. Removethe dimmer mounting screws.
4. Thereareup tothree screwterminalson the dimmer; thesearemarked
C. Nutral —White(Nutral)
D. Line —Black (connected topower)
E. Load —Black (connected tolighting)
5. ObserveImportant Wiring Information
IMPORTANT!: Thisdimmer is rated for and intended toonlybe used withcopper wire. WireGauge Requirements
Uselarger wiressuitablefor at least 80°Cfor supplying Line (HOT), Load, Neutral connections.
Uselarger wiressuitablefor at least 80°Cfor supplying Line (HOT), Load, Neutral connections.
Wirestriplength:
For attachment toscrewterminals: Stripinsulation 1", For attachment using the enclosures holes: Strip
insulation 5/8".
6. Connect the black wirethat goestothe light tothe terminal marked Load.
7. Connect the black wirethat comesfromthe electrical servicepanel (Hot) tothe terminal marked Line.
8. Connect the whitewiretothe neutral terminal marked Nutral (usejumper wireif needed).
9. Insert dimmer intothe switchboxbeing careful not topinchor crushwires.
10. Securethe dimmer tothe boxusing the supplied screws.
11. Mount the wall plate.
12. Reapplypower tothe circuit at fuseboxor circuit breaker and test the system.
Basic Operation
The connected light can be dimming intwo ways,
1. Manually fromthe front button of the In-wall dimmer
2. Remotely withaZ-WaveController
ManualControl
The Front button allows the user to:
dimthe connected fixture.
Todimming the connected light bright: Press the Up pushbutton.
Todimming the connected light dark: Press the Down pushbutton.
2. Linking your Z-Wavedevice
Reset your dimmertofactorydefault:
Usecontroller toremovedevicefromnetworkwill reset it tofactorydefault.
Pleaseusethis procedure onlyinthe event that the networkprimarycontroller is missing or otherwiseinoperable.
Adding device intothenetwork:
1. Follow the instructions of certified controller toinclude adevicefromdifferent manufactures intothe Z-Wavenetwork.
2. Oncethe controller is readytoinclude your device, triplepress the Up/Down pushbutton toinclude it
intothe network.

3. Onceyour controller has confirmed that the devicehas been included, refreshthe Z-Wavenetworkto
optimizeperformance.
4. The deviceis associated inthe samegroup when it included insetting process.Now you can controlyour
Z-Wavedeviceaccording togroups, scenes, schedules and automation programmed. If your controller
features remoteaccess, you can now controlall devices inZ-Wavenetworkfrommobiledevices.
To excludethedevice
1. Follow the instructions for your Z-Wavecertified controller toexclude adevicefromthe Z-Wavenetwork.
2. Oncethe controller is readytoExclude your device, triplepress the Up/Down pushbutton toexclude it
fromthe network.
Note
: 1. Your controller may need tobe within10 feet of the devicetobe included.
2. The association group supports fivenodes and lifeline function.
3. This product can be operated inanyZ-Wavenetworkwithother Z-Wavecertified devices from
other manufacturers. All non-batteryoperated nodes withinthe networkwill act as repeaters
regardless of vendor toincreasereliabilityof the network.
Packagecontent
In-wall Smart Dimmer-1pcs
Screw-3 pcs
Installation Operation manual-1pcs