Leviton 35249 User manual

PK-A3125-10-00-0A
The duplex receptacles included in this assembly are covered by U.S. Patent Nos.
7,355,117; 7,820,909; 7,868,719; 8,242,362 and corresponding foreign patents.
Two-Gang
Floor Box Assembly
Cat. No. 35249
Rated: 15A - 125V
Cat. No. 35349
Rated: 20A - 125V
Installation Instructions
NEMA Configurations
Bare Floor Installation Carpet Installation
15A - 125V
20A - 125V
Cat. No. 35249
Cat. No. 35349
WARNING: TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER AT CIRCUIT
BREAKER OR FUSE AND TEST THAT THE POWER IS OFF BEFORE WIRING!
CAUTION: To be installed and/or used in accordance with appropriate electrical codes
and regulations.
CAUTION: If you are unsure about any part of these instructions, contact an electrician.
CAUTION: Use this device with copper or copper clad wire only.
CAUTION: Electrical box is not suitable for masonry applications.
CAUTION: Suitable for wood finished floors and industrial carpet 3/8" (1.0 cm)
thickness only. Clean floor surfaces before mounting. Use all purpose sealing compound
(not provided) as shown.
CAUTION: Use only electrical mounting box provided.
!WARNINGS AND CAUTIONS
CONTENTS (Cat. Nos. 35249, 35349)
Screw Cap
O-Ring (Rubber)
Brass Plate
or Nickel Plate
Gasket
(2) Duplex
(4) #6 x 1"
(2) Mounting
(2) Shell
(4) O-Seal Washer
(4) Screw #6-32
Bracket
Head Screw
(4) Phil-Pan
(molded plastic)
Receptacle
(Cat. No. 35349
depicted)
Screw
(Brass or Nickel Plate)
(Brass or Nickel Plate)
For Technical Assistance Call:
1-800-824-3005 (U.S.A Only)
www.leviton.com
FOR CANADA ONLY
For warranty information and/or product returns, residents of Canada should contact Leviton
in writing at Leviton Manufacturing of Canada Ltd to the attention of the Quality Assurance
Department, 165 Hymus Blvd, Pointe-Claire (Quebec), Canada H9R 1E9 or by telephone
at 1 800 405-5320.
LIMITED 10 YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that
thisproductatthetimeofitssalebyLevitonisfreeofdefectsinmaterialsandworkmanshipunder
normalandproperusefortenyearsfromthepurchasedate.Leviton’sonlyobligationistocorrect
such defects by repair or replacement, at its option. For details visit www.leviton.com or call
1-800-824-3005. This warranty excludes and there is disclaimed liability for labor for removal
of this product or reinstallation. This warranty is void if this product is installed improperly
or in an improper environment, overloaded, misused, opened, abused, or altered in any
manner, or is not used under normal operating conditions or not in accordance with any
labels or instructions. There are no other or implied warranties of any kind, including
merchantability and fitness for a particular purpose, but if any implied warranty is
required by the applicable jurisdiction, the duration of any such implied warranty, including
merchantability and fitness for a particular purpose, is limited to ten years. Leviton is not
liable for incidental, indirect, special, or consequential damages, including without
limitation, damage to, or loss of use of, any equipment, lost sales or profits or delay
or failure to perform this warranty obligation. The remedies provided herein are the
exclusive remedies under this warranty, whether based on contract, tort or otherwise.
© 2016 Leviton Mfg. Co., Inc.
G
W
G
W
WEB VERSION

4" 4- "
17 32
Neutral
(White)
Hot (Black)
Grounding
Screw
(Green)
STEP 1 STEP 5
ADJUST AND TIGHTEN MOUNTING BRACKETS TO FLOOR BOX MOUNT COVER PLATE
IMPORTANT NOTE: Oval adjustment hole on bracket MUST be mounted to floor box.
Remove desired knockouts in floor box before mounting.
BARE FLOOR CARPET
NOTE: Ensure mounting brackets on the floor box are fully in the "DOWN" position.
Securely torque mounting bracket screws 12-14 in-lbs prior to floor installation.
NOTE: The floor box will be recessed (below floor surface),
when mounted properly. Follow steps for correct installation.
STEP 2 CUT CARPET (if applicable), and FLOOR
A) Cut a 4" x 4-17/32" hole in carpet in desired
location.
CAUTION: Do not cut carpet opening larger than
recommended dimensions. A larger opening
may compromise the integrity of the seal.
A) Place floor cut out template on floor in
desired location and trace.
B) Cut mounting area for floor box.
NOTE: Remove debris and clean
floor surfaces before mounting.
B) Place floor cut out
template (centered)
and trace.
C) Cut mounting
area for floor
box.
Carefully cut template along dotted line
BARE FLOOR CARPET
STEP 3 MOUNT FLOOR BOX, RECEPTACLE AND SHELL
B) Pull conductors. Wire and mount
receptacles.
C) Place plastic shells
over receptacles.
A) Mount box.
* Use sealing
compound
under brackets
STEP 4 SEAL DEVICE ACCORDING TO APPLICATION
BARE FLOOR CARPET
Sealing compound Sealing compound
Sealing
compound
• Apply sealing compound
• Add O-seal washers to cover plate screws
• Place gasket
• Apply sealing compound (2 places)
• Add O-seal washers to cover plate screws
Note: Gasket is not required for carpet
installations.
O-seal
washer
O-seal
washer
Gasket Carpet
NOTE: Use screw cap when not in use. Affix O-ring to screw cap. Apply an all purpose
silicone lubricant to O-ring before assembly. Torque screw cap to 20 in-lb.
NOTE: Torque mounting plate screws to 9 in-lb.
PK-A3125-10-00-0A
Floor Cut Out
Template
R 1/4" Typ
4-5/32"
"61/5-3
2-3/16"
2-13/16"
4-3/16"
WEB VERSION