Showline SL NITRO 510C User manual

SL NITRO 510C RGB & W LED Strobe Luminaire

Showline Offices
The material in this manual is for information purposes only and is subject to change without notice. Showline
assumes no responsibility for any errors or omissions which may appear in this manual. For comments and
suggestions regarding corrections and/or updates to this manual, please contact your nearest Showline office.
El contenido de este manual es solamente para información y está sujeto a cambios sin previo aviso. Showline no
asume responsabilidad por errores o omisiones que puedan aparecer. Cualquier comentario, sugerencia o corrección
con respecto a este manual, favor de dirijirlo a la oficina de Showline más cercana.
Der Inhalt dieses Handbuches ist nur für Informationszwecke gedacht, Aenderungen sind vorbehalten. Showline
uebernimmt keine Verantwortung für Fehler oder Irrtuemer, die in diesem Handbuch auftreten. Für Bemerkungen
und Verbesserungsvorschlaege oder Vorschlaege in Bezug auf Korrekturen und/oder Aktualisierungen in diesem
Handbuch, moechten wir Sie bitten, Kontakt mit der naechsten Showline-Niederlassung aufzunehmen.
Le matériel décrit dans ce manuel est pour information seulement et est sujet à changements sans préavis. La
compagnie Showline n'assume aucune responsibilité sur toute erreur ou ommission inscrite dans ce manuel. Pour
tous commentaires ou suggestions concernant des corrections et/ou les mises à jour de ce manuel, veuillez s'il vous
plait contacter le bureau de Showline le plus proche.
Note: Information contained in this document may not be duplicated in full or in part by any person without prior written
approval of Showline. Its sole purpose is to provide the user with conceptual information on the equipment mentioned. The use of
this document for all other purposes is specifically prohibited.
Document Number: SL NITRO 510C LED STROBE Luminaires Users
Version as of: 08 April 2014
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual
©2014 Philips Group. All rights reserved.
Dallas
10911 Petal Street
Dallas, TX 75238
Tel: [phone]
Fax: [phone]
Auckland
19-21 Kawana Street
Northcote, Auckland 0627
New Zealand
Tel: [phone]
Fax: [phone]
Asia
Unit C, 14/F, Roxy Industrial Centre
No. 41-49 Kwai Cheong Road
Kwai Chung, N.T., Hong Kong
Tel: [phone]
Fax: [phone]
Europe
Rondweg zuid 85
Winterswijk 7102 JD
The Netherlands
Tel: [phone]
www.philips.com/showline
INTENSE STROBE LIGHT WARNING!
• Strobe lights are known to trigger epileptic seizures in persons who are photosensitive to intense flashing
lights.
• Do not operate the fixture near stairways or in small confined spaces.
• Avoid extended periods of continuous flashing, particularly at frequencies of 10 to 20 flashes per second.
• Owners, users, and facilities using this luminaire should adhere to all local and national requirements of
posting warning signs for strobe light use and strobe light effects. This posted warning should be
available and visible to anyone attending or performing when the luminaire is in use.

1
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual
Sh wline
IMPORTANT INFORMATION
Warnings and Notices
Additional Resources for DMX512
For more information on installing DMX512 control systems, the following publication is available for purchase
from the United States Institute for Theatre Technology (USITT), "Recommended Practice for DMX512: A Guide
for Users and Installers, 2nd edition" (ISBN: 9780955703522). USITT Contact Information:
USITT
315 South Crouse Avenue, Suite 200
Syracuse, NY 13210-1844
Phone: [phone] or 1.315.463.6463
www.usitt.org
Showline Limited Two-Year Warranty
Showline offers a two-year limited warranty of its luminaires against defects in materials or workmanship from the
date of delivery. A copy of Showline two-year limited warranty containing specific terms and conditions can be
obtained by contacting your local Showline office.
When using electrical equipment, basic safety precautions should always be followed including the following:
a. READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
b. Do not use outdoors.
c. Do not mount near gas or electric heaters.
d. Equipment should be mounted in locations and at heights where it will not readily be subjected to
tampering by unauthorized personnel.
e. The use of accessory equipment not recommended by the manufacturer may cause an unsafe
condition.
f. Do not use this equipment for other than intended use.
g. Refer service to qualified personnel.
SAVE THESE INSTRUCTIONS.
WARNING: You must have access to a main circuit breaker or other power disconnect device
before installing any wiring. Be sure that power is disconnected by removing fuses or turning the
main circuit breaker off before installation. Installing the device with power on may expose you to
dangerous voltages and damage the device. A qualified electrician must perform this installation.
WARNING: Refer to National Electrical Code® and local codes for cable specifications. Failure to
use proper cable can result in damage to equipment or danger to personnel.
WARNING: This equipment is intended for installation in accordance with the National Electric
Code® and local regulations. It is also intended for installation in indoor applications only. Before
any electrical work is performed, disconnect power at the circuit breaker or remove the fuse to avoid
shock or damage to the control. It is recommended that a qualified electrician perform this
installation.

Installation & User’s Manual SL NITRO 510C LED STROBE Luminaire
2TABLE OF CONTENTS Sh wline
TABLE OF CONTENTS
Showline Offices..................................................................................................................................... Insdie Front Cover
IMPORTANT INFORMATION
Warnings and Notices......................................................................................................................................................... 1
Additional Resources for DMX512.................................................................................................................................... 1
Showline Limited Two-Year Warranty.............................................................................................................................. 1
TABLE OF CONTENTS
PREFACE
About this Manual ...................................................................................................................................................................... 4
Included Items............................................................................................................................................................................. 4
Accessories ................................................................................................................................................................................. 4
SL NITRO 510C LED STROBE Luminaire Power Input Cables (North American Models Only).................................. 4
SL NITRO 510C LED STROBE Luminaire Accessories.................................................................................................. 4
SL NITRO 510C LED STROBE LUMINAIRE OVERVIEW
SL NITRO 510C LED STROBE Luminaire Components......................................................................................................... 5
Major Luminaire Components............................................................................................................................................ 5
LCD Display / Menu System.............................................................................................................................................. 6
INSTALLATION AND SET UP
Power Requirements................................................................................................................................................................... 7
AC Power Operation........................................................................................................................................................... 7
Connecting Power....................................................................................................................................................................... 8
Connecting SL NITRO 510C LED STROBE Luminaires to AC Power ........................................................................... 8
Connecting to the DMX512 Network......................................................................................................................................... 9
Mounting Luminaire................................................................................................................................................................... 9
Connecting & Mounting Multiple Luminaires......................................................................................................................... 10
Connecting Luminaires Top-to-Bottom............................................................................................................................ 11
Connecting Luminaires Side-to-Side................................................................................................................................ 12
Mounting SL NITRO 510C LED STROBE Luminaire with Other Luminaires...................................................................... 12
Connecting Combined Luminaires Top-to-Bottom.......................................................................................................... 13
Connecting Combined Luminaires Side-to-Side.............................................................................................................. 15
OPERATION AND PROGRAMMING
LCD Display and Menu System............................................................................................................................................... 16
LCD Display and Menu System Operation.............................................................................................................................. 16
SL NITRO 510C LED STROBE Luminaire Main Menu Options........................................................................................... 17
Presets............................................................................................................................................................................... 17
Recalling or Editing Presets.............................................................................................................................................. 17
Effects............................................................................................................................................................................... 18
Editing User Chases.......................................................................................................................................................... 18
Settings/Security............................................................................................................................................................... 18
Settings/General................................................................................................................................................................ 19
Settings/Factory Default ................................................................................................................................................... 19
Settings/DMX................................................................................................................................................................... 19
Settings/Display................................................................................................................................................................ 20
Lock Fixture...................................................................................................................................................................... 20
Password (PassPIN).......................................................................................................................................................... 20
Status................................................................................................................................................................................. 20
Quick Selection Buttons ................................................................................................................................................... 21
DMX Address................................................................................................................................................................... 21
Harmonize Color Calibration.................................................................................................................................................... 21
Dimming Curve Selection ........................................................................................................................................................ 22
Master / Slave Operational Mode............................................................................................................................................. 23
DMX CONTROL
RGB & W Operation ................................................................................................................................................................ 24
DMX Maps............................................................................................................................................................................... 24
RGBW Full Mode..................................................................................................................................................................... 24
RGBW Full Mode (Zones) ....................................................................................................................................................... 28

3
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual
Sh wline
RGBW Expanded Mode........................................................................................................................................................... 29
RGBW Expanded Mode (Zones).............................................................................................................................................. 32
RGBW 16-Bit Mode................................................................................................................................................................. 33
RGBW 16-Bit Mode (Zones) ................................................................................................................................................... 36
RGBW 8-Bit Mode................................................................................................................................................................... 37
RGBW 8-Bit Mode (Zones) ..................................................................................................................................................... 40
6-Channel Mode ....................................................................................................................................................................... 41
Mapping 16-Bit Mode .............................................................................................................................................................. 44
SL NITRO 510C LED Groups/Zones ...................................................................................................................................... 45
Strobe Rate DMX Timing Detail.............................................................................................................................................. 46
Strobe Duration DMX Timing Detail....................................................................................................................................... 47
SL NITRO 510C LED STROBE Luminaire RDM Parameter IDs.......................................................................................... 48
CLEANING AND CARE
Special Cleaning and Care Instructions.................................................................................................................................... 52
Front Lens Cleaning.................................................................................................................................................................. 52
Service and Maintenance.......................................................................................................................................................... 52
TECHNICAL SPECIFICATIONS
SL NITRO 510C LED STROBE Luminaire Operational Specifications................................................................................. 53
SL NITRO 510C LED STROBE Luminaire Dimensions........................................................................................................ 53

Installation & User’s Manual SL NITRO 510C LED STROBE Luminaire
4PREFACE Sh wline
PREFACE
1. About this Manual
The document provides installation and operation instructions for the following products:
• SL NITRO 510C LED STROBE Luminaire
Please read all instructions before installing or using this product. Retain this manual for future reference. Additional
product information and descriptions may be found on the product specification sheet.
Note: The SL NITRO 510C LED STROBE Luminaire is universal voltage 100 to 240 VAC (auto-ranging).
2. Included Items
Each SL NITRO 510C LED STROBE Luminaire includes the following items:
Figure 1: Included Items
3. Accessories
SL NITRO 510C LED STROBE Luminaire Power Input Cables (North American Models
Only)
SL NITRO 510C LED STROBE Luminaire Accessories
SL NITRO 510C LED Luminaire AC Input Cable (1M)
Luminaire Connecting Back Pin (2 each)
(for joining luminaires end-to-end)
Yoke Plate
Yoke Plate Hardware
Includes:
2 Ea - Mounting Bolt (M12 x 25)
2 Ea - Flat Washer
2 Ea - Lock Washer
2 Ea - Nut (M12)
Luminaire Connecting Front Pin (1 each)
(for joining luminaires end-to-end)
(USA, Canada, & Latin
AC Input Cable (1.5M)
(International Markets Only)
QuickStart Guide
America Markets Only)
Part Number Description
PC1BE SL NITRO 510C LED STROBE Luminaire AC Power Input Cable (39 inches / 1 meter), Powercon
with Bare End* (*Note, user supplies and installs own AC input connector)
PC1GP SL NITRO 510C LED STROBE Luminaire AC Power Input Cable (39 inches / 1 meter), Powercon
with Stagepin Connector
PC1GTL SL NITRO 510C LED STROBE Luminaire AC Power Input Cable (39 inches / 1 meter), Powercon
with Twistlock Connector
PC1GR SL NITRO 510C LED STROBE Luminaire AC Power Input Cable (39 inches / 1 meter), Powercon
with Edison Connector
PC3BE SL NITRO 510C LED STROBE Luminaire AC Power Input Cable (9.8 Feet / 3 meter), Powercon with
Bare End* (*Note, user supplies and installs own AC input connector)
PC8BE SL NITRO 510C LED STROBE Luminaire AC Power Input Cable (26 Feet / 8 meter), Powercon with
Bare End* (*Note, user supplies and installs own AC input connector)
PC8GR SL NITRO 510C LED STROBE Luminaire AC Power Input Cable (26 Feet / 8 meter), Powercon with
Edison Connector
Part Number Description
MC Mega Claw, Black, Anodized
SC Molded Yoke C-Clamp
HC Light Weight Half Coupler
82003 Safety Cable
SLPIN1 Luminaire Connecting Front Pin (North American Models Only)
SLPIN2 Luminaire Connecting Back Pin (North American Models Only)

SL NITRO 510C LED STROBE Luminaire Components 5
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual
Sh wline
SL NITRO 510C LED STROBE LUMINAIRE OVERVIEW
1. SL NITRO 510C LED STROBE Luminaire Components
Major Luminaire Components
Figure 2: SL NITRO 510C LED STROBE Luminaire Components
Back of Fixture DMX512 /
AC Input
Luminaire Mount (x2)
RDM Input
Front of Fixture
DMX512 /
AC Output
RDM Output
High-Intensity RGB & W LED Array
Luminaire Mount Lock (x2)
Quick Connect
Locking Pin (x2)
LCD Display / Menu System*
(*refer to "LCD Display / Menu System" on page 6 for
additional information)

Installation & User’s Manual SL NITRO 510C LED STROBE Luminaire
6SL NITRO 510C LED STROBE LUMINAIRE OVERVIEW Sh wline
LCD Display / Menu System
Figure 3: LCD Display & Menu System
Note: For Menu operation and programming details, refer to "LCD Display and Menu System" on page 16.
Home (menu settings)
Edit a Preset Edit a Chase
DMX512 Addressing
Return to Main Screen
LEFT Arrow Button
UP Arrow Button
CHECK MARK (Accept) Button
DOWN Arrow Button
RIGHT Arrow Button
LCD Display
NOTE: Menu rotates with orientation of luminaire and
menu buttons are always in the same position (with
rotation of menu)
To rotate menu 180
degrees from current
orientation, press and
hold the two center
buttons for 2 seconds.

Power Requirements 7
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual
Sh wline
INSTALLATION AND SET UP
1. Power Requirements
The SL NITRO 510C LED STROBE Luminaire operates on AC input voltages from 100 to 240 VAC.
WARNING! This unit does not contain an ON/OFF switch. Always disconnect power input cable to completely
remove power from unit when not in use.
AC Power Operation
When connected to an AC source, the unit operates on 100 to 240 volts AC (+/- 10%, auto-ranging). The luminaire
contains an auto-ranging power supply. Each luminaire can draw up to 360 Watts.
WARNING! Maximum amount of units that may be daisy-chained is (A) 5 units 100VAC (20 Amps) or (B) 13 units
240VAC (20 Amps). Refer to Table 1 for detailed information at various voltages.
Note: For wiring of AC input connector, refer to "Connecting SL NITRO 510C LED STROBE Luminaires to AC
Power" on page 8.
WARNING! *These figures are based on the Maximum Allowable Input Current of 20 Amps (and the maximum
power supply limit of 360 Watts). Do not overload circuits!
Table 1: SL NITRO 510C LED STROBE Luminaire Voltage vs. Current
Voltage
(AC) Total Current (A)
Maximum
number of
units that can
be linked
together*
Voltage
(AC) Total Current (A)
Maximum
number of
units that can
be linked
together*
1003.60 5 1802.00 10
110 3.27 6 190 1.89 10
1203.00 6 2001.80 11
1302.77 7 2101.72 11
1402.57 7 2201.64 12
1502.40 8 2301.57 12
1602.25 8 2401.50 13
170 2.12 9
IMPORTANT AC POWER CONNECTION NOTES:
a. When using the daisy-chain connection method, ONLY connect SL NITRO 510C LED
STROBE Luminaires to AC Output Connection of SL NITRO 510C LED STROBE
Luminaires. DO NOT CONNECT OTHER TYPES OF LUMINAIRES OR DEVICES!
b. Use only use approved cable types.
c. Do not overload circuits!
d. Do not connect SL NITRO 510C LED STROBE Luminaires to dimmed circuits.
e. The MAXIMUM allowable number of SL NITRO 510C LED STROBE Luminaires which
can be 'daisy-chained' on one power feed are listed in Table 1, above. DO NOT EXCEED!

Installation & User’s Manual SL NITRO 510C LED STROBE Luminaire
8INSTALLATION AND SET UP Sh wline
2. Connecting Power
Units can be powered in one of two ways:
• Direct connection to a AC power source using an AC input cable. For wiring of AC input connector, refer to "Con-
necting SL NITRO 510C LED STROBE Luminaires to AC Power" on page 8.
• Connection from the AC output of another SL NITRO 510C LED STROBE Luminaire. When using this method,
it is very important not to connect any other type of equipment device.
WARNING! Only connect other SL NITRO 510C LED STROBE Luminaires to the AC Output (Thru) connector of
a SL NITRO 510C LED STROBE Luminaire.
Connecting SL NITRO 510C LED STROBE Luminaires to AC Power
If the unit is supplied with an AC input cable without an input connector installed. The input connector is a user-
supplied accessory.
Table 2 on page 8 describes how to connect power to your SL NITRO 510C LED STROBE Luminaire. Field wiring
of the SL NITRO 510C LED STROBE Luminaire is straight forward. A total of 3 wires/conductors is supplied from
the unit. The following wiring scheme is used:
Table 2: SL NITRO 510C LED STROBE Luminaire (IP20 Rated Models) AC Input Connections
CAUTION: In the event the supplied AC input cable (international markets - outside North America) OR AC input
connector (North American markets) is damaged, they must be replaced with an approved replacement through your
Authorized Showline Dealer or Service Center.
Figure 4: SL NITRO 510C LED STROBE Luminaire AC Input & Output Connections
Wire Color Purpose
Brown Main / Line (100 to 240VAC)
Blue Neutral
Green/Yellow Ground (Earth)
AC Input AC Output
Neutral Main /
Ground / Earth
Line
AC Connector
(on side of unit)
AC Input Connector (on Unit)
Neutral
Main /
Ground / Earth
Line
AC Connector
(on side of unit)
AC Output Connector (on Unit)
Back of Fixture

Connecting to the DMX512 Network 9
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual
Sh wline
3. Connecting to the DMX512 Network
Basic DMX512 installation consists of connecting multiple SL NITRO 510C LED STROBE Luminaires together (up
to 32 luminaires) in "daisy-chain" fashion. A cable runs from the control console (or DMX512 control source) to the
DMX connector on the first SL NITRO 510C LED STROBE Luminaire. Another cable runs from the other DMX
connector on the first unit to a DMX connector on the next SL NITRO 510C LED STROBE Luminaire (or DMX512
device to be controlled).
Figure 5: SL NITRO 510C LED STROBE Luminaire DMX512 Input / Output Connections
Note: For more information on DMX512 networking and systems, refer to "Additional Resources for DMX512" on
page 1. For SL NITRO 510C LED STROBE Luminaire DMX Mapping, refer to "DMX CONTROL" on page 24.
Figure 6: SL NITRO 510C LED STROBE Luminaire - DMX512 Connections
4. Mounting Luminaire
SL NITRO 510C LED STROBE Luminaires are provided with the ability to hang via truss hooks, clamps, etc. (sold
separately). Simply attach hook, clamp, etc. to the SL NITRO 510C LED STROBE Luminaire’s mounts in the
DMX512 / RDM Input DMX512 / RDM Output
Back of Fixture
DMX512
DMX512 (out from first
to second luminaire)
DMX512 Connections
Note: Remaining pins on each connector are not used.
DMX512 Signal XLR Pin
Common (Drain) 1
DMX512 - 2
DMX512 + 3
(from console or
control device)
SL NITRO 510C LED
STROBE Luminaires
DMX512 (out to the next luminaire
or DMX512 controlled device)

Installation & User’s Manual SL NITRO 510C LED STROBE Luminaire
10 INSTALLATION AND SET UP Sh wline
provided M9 holes. It is recommended (and may be required by local and national safety codes) to use and install a
safety cable (sold separately). When hanging the fixture, be sure to leave enough space around the luminaire to allow
proper, uninterrupted airflow for cooling and positioning.
Figure 7: Mounting Luminaire
5. Connecting & Mounting Multiple Luminaires
SL NITRO 510C LED STROBE Luminaires include a built-in Quick Connect system that allows the luminaires to be
physically connected together while retaining perfect pixel pitch. Units may be connected in top-to-bottom or side-
by-side to allow for a wide range of configurations. In addition, they may be connected together with the SL BAR
520 RGBW LED luminaire.
Note: The SL NITRO 510C LED STROBE Luminaire and SL NITRO 510 LED Strobe Luminaire share the same
chassis and can be combined together (or substituted for each other) as shown in this section of the manual.
SAFETY CABLE: Is sold separately and
recommended for all hanging installation
and may be required by national and local
codes. Use safety cable anchor points for
safety cable attachment for this fixture.
Mounting
Hook / Clamp
Mounting holes
are M13.
Note:
(sold separately)
Yoke Plate
Point (2 ea.)
Mounted with Yoke Plate*
Mounted without Yoke Plate
Accessory
Hooks / Clamps
(sold separately)
SAFETY CABLE: Is sold separately and
recommended for all hanging installation
and may be required by national and local
codes. Use safety cable anchor points for
safety cable attachment for this fixture.
*Each SL NITRO 510 LED STROBE luminaire
includes an accessory Yoke Plate. This can be added
to the luminaire to allow hanging with a single clamp.
Bolt (x4)
Flat Washer (x4)
Lock Washer (x4)
Nut (x4)
Yoke Plate

Connecting & Mounting Multiple Luminaires 11
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual
Sh wline
Connecting Luminaires Top-to-Bottom
Each SL NITRO 510C LED STROBE Luminaire includes two built-in Quick Connect slot and pin systems as
illustrated in Figure 8. This allows a quick connection of units when stacked on top of each other. Up to twenty SL
NITRO 510C LED STROBE Luminaires may be supported when connected using the Quick Connect system.
Figure 8: Connecting Luminaires Top-to-Bottom
WARNING! Your structure must be capable of properly supporting the weight of multiple connected fixtures. Each
fixture must use an approved safety cable attached to a fixed object. Up to twenty SL NITRO 510C LED STROBE
Luminaires may be supported when connected using the Quick Connect system. When connecting units together,
ensure all Quick-Connect pins are in the "engaged" position.
Side View
Step 1. Move locking mechanism
handle so locking pin clears
locking mechanism
Step 2. Lock Locking Mechanism
Handle so pin does not move
back to locking position.
Step 3. Carefully slide fixture to be
connected into both locking
mechanisms on lower
fixture.
Step 4. Return locking pin to locked
position on each side
(securing upper fixture to
lower fixture).
Locking Mechanism
Locking Mechanism Pin
Fixture 1
Fixture 2
Fixture 1
Fixture 2
1
2
3
4
Fixture 1
Some components not shown for clarity.
NOTE:

Installation & User’s Manual SL NITRO 510C LED STROBE Luminaire
12 INSTALLATION AND SET UP Sh wline
Connecting Luminaires Side-to-Side
Each SL NITRO 510C LED STROBE Luminaire ships with three Luminaire Connecting Pins as indicated in Figure
9. All three pins are used to connect two luminaires together linearly. Each fixture must be mounted using its own
mounting hardware. The side-to-side pins are only to align the luminaires and do not provide hanging support.
Figure 9: Connecting Luminaires Side-to-Side
WARNING! Each fixture must use an approved safety cable attached to a fixed object.
6. Mounting SL NITRO 510C LED STROBE Luminaire with Other
Luminaires
The SL NITRO 510C LED STROBE Luminaire and SL BAR 520 LED Luminaire are designed to be connected
together top-to-bottom and/or end-to-end using the same connecting hardware. The pixels of the SL BAR 520 LED
Luminaire and the zones of the SL NITRO 510C LED STROBE Luminaire will be perfectly aligned when connected
via the built-in connecting hardware.
Figure 10: Combining SL NITRO 510C and SL BAR 520 luminaires
Front Pin (x1)
Back Pin (x2)
A
B
A
B
A
B
SL NITRO 510C LED
SL BAR 520 LED Luminaire
SL BAR 520 LED Luminaire
STROBE Luminaire (x2)
Note, all luminaires are sold separately.

Mounting SL NITRO 510C LED STROBE Luminaire with Other Luminaires 13
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual
Sh wline
Connecting Combined Luminaires Top-to-Bottom
When combining units connected top-to-bottom, two SL NITRO 510C LED STROBE Luminaires are first connected
end-to-end and then connected top-to-bottom with a single SL BAR 520 luminaire.
Connecting Notes:
WARNING! Do not exceed 10 rows of combined luminaires connected together top-to-bottom with a single hanging
point. If more than 10 rows are required, each ten rows must use its own connection to a fixed object.
• The two SL NITRO 510 units must have all three side-to-side pins installed (refer to Figure 11 and "Connecting
Luminaires Side-to-Side" on page 12).
Figure 11: SL NITRO 510C LED STROBE Luminaires - Connections
• When two SL NITRO 510C LED STROBE Luminaires are combined with a SL BAR 520, there is no top-to-bot-
tom connection available in the center.
• When a SL BAR 520 unit is mounted below the two SL NITRO 510C LED STROBE Luminaires, the top-to-bot-
tom connections will rest on the center of the SL BAR 520, preventing the units from spreading apart in the center.
• If the bottom of a configuration has two SL NITRO 510C LED STROBE Luminaires below a single SL BAR 520,
connect the bottom center top-to-bottom connections with the following hardware (available from others) to pre-
OR
SL BAR 520 LED Luminaire
SL NITRO 510C LED
SL NITRO 510C LED
SL BAR 520 LED Luminaire
STROBE Luminaires
STROBE Luminaires

Installation & User’s Manual SL NITRO 510C LED STROBE Luminaire
14 INSTALLATION AND SET UP Sh wline
vent the spacing between the two SL NITRO 510C LED STROBE Luminaires from spreading apart at the center.
Obtain and install:
1) One M10-1.5 x 25 mm Long, Hex Head Cap Bolt
2) One 10 mm Flat Washer
3) One 10 mm Split-Lock Washer
4) One M10-1.5 (8 mm high) Hex Nut
• Installation is Flat Washer under Bolt Head, Bolt through both SL NITRO 510C LED STROBE Luminaire brack-
ets, Lock Washer, and then Hex Nut. Hand tighten.
WARNING! Your structure must be capable of properly supporting the weight of multiple connected fixtures. Each
fixture must use an approved safety cable attached to a fixed object. Up to ten luminaire rows may be supported when
connected using the Quick Connect system.
Bolt
Flat Washer Lock Washer
Nut
Note, hardware shown available from others.
SL NITRO 510C LED STROBE Luminaires
See detail below
SL BAR 520 LED Luminaire
SL NITRO 510C LED
STROBE Luminaires

Mounting SL NITRO 510C LED STROBE Luminaire with Other Luminaires 15
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual
Sh wline
Connecting Combined Luminaires Side-to-Side
When combining units connected side-to-side, all units connect using the same pin system and any combination can
be created (refer to installation instructions and warnings contained in "Connecting Luminaires Side-to-Side" on page
12).
• Each SL NITRO 510C LED STROBE Luminaire and SL BAR 520 RGBW Luminaire ships with three Luminaire
Connecting Pins as indicated in Figure 9.
• The three side-to-side pins must be installed per luminaire.
• All three pins are used to connect luminaires together linearly. Each fixture must be mounted using its own mount-
ing hardware. The side-to-side pins are only to align the luminaires and do not provide hanging support.
•Figure 12 shows an example of connecting luminaires side-by-side.
Figure 12: Connecting Combined Luminaires Side-to-Side Example
WARNING! Each fixture must use an approved safety cable attached to a fixed object.
SL BAR 520 LED Luminaire
SL NITRO 510C LED STROBE Luminaire
Front View
Rear View
See Detail
Connecting Pin
Connecting Pin (x2)
SL BAR 520 LED Luminaire
SL NITRO 510C LED STROBE Luminaire
Note, all luminaires are sold separately.

Installation & User’s Manual SL NITRO 510C LED STROBE Luminaire
16 OPERATION AND PROGRAMMING Sh wline
OPERATION AND PROGRAMMING
1. LCD Display and Menu System
The SL NITRO 510C LED STROBE Luminaire’s LCD Display and Menu System provides local control for
accessing the following fixture’s settings:
• Presets (Standard and User Defined)
• Effects (Chases - preloaded and user defined)
• Strobe / Timing
• Fixture Settings
• Fixture Lockout (to prevent changes)
• Password Setting
• Current Fixture Operational Status
• Setting the DMX512 Address
Note: If there are multiple luminaires in a system, changes would need to be made at each LCD Menu as desired. For
SL NITRO 510C LED STROBE Luminaire menu structure, see "SL NITRO 510C LED STROBE Luminaire Main
Menu Options" on page 17.
Upon power up, the LCD will display the main screen showing the product type/name. If DMX is enabled, the
programmed address will appear after power up.
2. LCD Display and Menu System Operation
The LCD Display Menu system consists of several categories. Use the Menu Buttons to access and make changes to
the menu items. When the desired menu item is reached, press the desired Menu Button to display the menu options
and to navigate and configure the menu options as required.
To navigate and access menu settings/selections:
Step 1. Make sure unit is powered and turned on.
Step 2. Press the desired button (as shown in Figure 13 on page 17) to access menu categories.
Step 3. Use UP | DOWN | LEFT | RIGHT arrow buttons to navigate through the various options and settings.
Step 4. Make changes as desired.
Step 5. Press CHECK MARK (OK) button to accept changes.

SL NITRO 510C LED STROBE Luminaire Main Menu Options 17
SL NITRO 510C LED STROBE Luminaire Installation & User’s Manual
Sh wline
.
Figure 13: LCD Display and Menu System
3. SL NITRO 510C LED STROBE Luminaire Main Menu Options
Presets
Presets are stored values of the luminaire's LED settings that can be recalled via the menu system or DMX. You can
customize up to 31 presets via the menu system.
Recalling or Editing Presets
To recall or edit a preset:
Step 1. Select Preset from the main menu or from the Preset shortcut key.
Step 2. The top left field indicates the current preset or Off, when this field is
selected (highlighted in blue), use the left and right buttons to scroll
through all presets
Step 3. If you wish to edit the preset, use the Up and Down keys to scroll through
the parameters. Once a parameter is selected, use the left and right arrow
buttons to make adjustments.
Notes:
• If security features are enabled, the Up and Down arrows will have no effect. See "Settings/Security" on page 18.
• Depending on the DMX map set assigned the DMX menu, different parameters will be available. See "DMX
CONTROL" on page 24 for additional information.
Step 4. Once all values are adjusted as desired, press the Check Mark button to save the preset.
Step 5. The Save Preset Menu option will appear. Use the left and right arrow buttons to select the preset number to
save to.
Note: This function allows you to save your current edits to a different preset number than you began editing. This is
helpful to create copies of existing presets.
Step 6. Press the Check Mark button to save the preset. You will be asked to confirm your saving operation.
Home (menu settings)
Edit a Preset Edit a Chase
DMX512 Addressing
Return to Main Screen /
LEFT Arrow Button
UP Arrow Button OK (Check Mark) Button
DOWN Arrow Button
RIGHT Arrow Button
LCD Display
NOTE: Menu rotates with orientation of Luminaire and
menu buttons are always in the same position (with
rotation of menu)
To rotate menu 180 degrees manually from current
orientation, press and hold the two center buttons for 2
seconds.
Return Up One Level
Edit a Preset
MASTER INTENSITY 100 %
STROBE RATE Single
STROBE DURATION 0mS
EFFECTS No Ef fect
Edit a Preset

Installation & User’s Manual SL NITRO 510C LED STROBE Luminaire
18 OPERATION AND PROGRAMMING Sh wline
Step 7. The preset is now saved and can be recalled via the menu or DMX.
Effects
Effects are chases stored values of the luminaire's LED settings that can be recalled via the menu system or DMX.
There are 10 factory defined chases and eight user adjustable chases. You can adjust the master intensity, speed, and
fade values for any of the 18 chases.
Use the Up and Down buttons to select parameters and the Left and Right buttons to assign the different general
fixture settings. When finished, press the Check button to exit the menu level. The adjustable parameters are
described in Table 3.
Editing User Chases
Eight User chases can be further customized to create different effects on the
fixture. To edit a User Chase, first use the up and down arrows to scroll to the Edit
User Chase field and then press the Check Mark button. The Edit User Chase
window will be displayed:
Use the Up and Down buttons to select parameters and the Left and Right buttons
to assign the different general fixture settings. When finished, press the Check
button to exit the menu level.
To edit and save a Step:
Step 1. Select Edit Step or New Step from the Edit User Chase menu.
Step 2. The top left field indicates the preset or color filter to be used for the step. When set to OFF no preset or
color filter is to be used. Use the left and right buttons to scroll through all presets and color filters.
Step 3. Use the Up and Down keys to scroll through the output parameters. Once a parameter is selected, use the
left and right arrow buttons to make adjustments.
Notes:
• If security features are enabled, the Up and Down arrows will have no effect. See "Settings/Security" on page 18.
• Depending on the DMX map set assigned the DMX menu, different parameters will be available. See "DMX
CONTROL" on page 24 for additional information.
Step 4. Once all values are adjusted as desired, press the Check Mark button to return to the Edit
User Chase screen.
Step 5. Continue editing steps as needed. When complete, press the Return to Main Menu button
or up one level (as shown to the right). to exit the Edit User Chase window.
Step 6. The user chase is now saved and can be recalled via the menu or DMX.
Settings/Security
All Showline fixtures have a multiple level locking feature. This allows you to configure the fixture and allow
different menu access to multiple users. The menu system can be locked instantly or assigned to power on to a
particular lock level. You can assign three different 4-digit PIN (personal identification number) codes to each unlock
specific levels of functionality within the menu system.
Anytime the fixture is locked, each PIN code will unlock all functions except the pertaining features assigned via the
security level.
Table 3: Effects Parameters
Parameter Description
User Chase / Built-in Chase Select from the 18 different chases.
Master Intensity Adjust the master intensity for ALL chases.
Total Steps Displays the total steps used by the chase. This field is not editable.
Speed The total time each step of the chase will be recalled.
Fade The percentage of the time assigned by the speed that is crossfaded between steps.
Edit a Chase
User Chase: 2
Master Intensi ty 39 %
Total Steps 3
Edit User Chase
Fade 100 %
Speed 1S
Edit a Chase
Return to Main
Menu button