Si Tech GCS900 HEX User manual

Field Reference Guides
GCS900 HEX
Version 13.13
SITECH Rocky Mountain
www.sitechrockymtn.com

SITECH TECHNOLOGY DEALER
TRAINING CHECKLIST
CUSTOMER COPY
Training Acknowledgement:
Customer Signature
Date
SITECH Representative
Date
System:
GCS900 HEX
Version:
13.1
Training Checklist
Page #
□
CB460 Control Box Layout
3
□
HEX Training Display Settings
4
□
Check Bucket Wear
6
□
Load Design
7
□
Verify System Accuracy
8
□
Verify Sensor Accuracy
9
□
Vertical Offset
10
□
Horizontal Offset
11
□
Vertical Guidance
13
□
Cut and Fill Site Map
14
□
UTS Set-Up
15
□
Lane Guidance
16
□
Create New Bucket
17
□
Connect to Wi-Fi
18
□
TCC Settings
19
□
Configure Remote Assistant
20
□
Wireless Data Sync
21
□
Start Remote Assistant
22
□
Connect to IBSS Base
23

SITECH TECHNOLOGY DEALER
TRAINING CHECKLIST
SITECH COPY
Training Acknowledgement:
Customer Signature
Date
SITECH Representative
Date
System:
GCS900 HEX
Version:
13.1
Training Checklist
Page #
□
CB460 Control Box Layout
3
□
HEX Training Display Settings
4
□
Check Bucket Wear
6
□
Load Design
7
□
Verify System Accuracy
8
□
Verify Sensor Accuracy
9
□
Vertical Offset
10
□
Horizontal Offset
11
□
Vertical Guidance
13
□
Cut and Fill Site Map
14
□
UTS Set-Up
15
□
Lane Guidance
16
□
Create New Bucket
17
□
Connect to Wi-Fi
18
□
TCC Settings
19
□
Configure Remote Assistant
20
□
Wireless Data Sync
21
□
Start Remote Assistant
22
□
Connect to IBSS Base
23

Field Reference Guide
SITECH TECHNOLOGY DEALER
Table of Content GCS900 HEX
Version: 13.1
Field Reference Guide
Page #
CB460 Control Box Layout
3
HEX Training Display Settings
4
Check Bucket Wear
6
Load Design
7
Verify System Accuracy
8
Verify Sensor Accuracy
9
Vertical Offset
10
Horizontal Offset
11
Vertical Guidance
13
Cut and Fill Site Map
14
UTS Set-Up
15
Lane Guidance
16
Create New Bucket
17
Connect to Wi-Fi
18
TCC Settings
19
Configure Remote Assistant
20
Wireless Data Sync
21
Start Remote Assistant
22
Connect to IBSS Base
23

Field Reference Guide
SITECH TECHNOLOGY DEALER
Next Key
Escape / Go Back 3D Reach Position
2D Laser Strike
Function Keys (F1-F6) Zoom In - Out
Power Menu USB Port Enter
Cut / Fill Horizontal Position

Field Reference Guide
SITECH TECHNOLOGY DEALER
GCS900 HEX Training Display Settings
Version: 13.1
The Control Box must be in Manager’s Mode
1. Press “Menu”
2. Select “GNSS Accuracy” and Press “OK”
3. Press and Hold “F6 ” and Press “F2” Medium Mode
4. Change “GPS Horizontal error limit:” to “0.30ft or 0.090m” and Press “Next”
5. Change “GPS Vertical error limit:” to “0.30ft or 0.090m” and Press “OK” Twice
6. Select “Guidance Method” and Press “OK”
7. Use Arrow to change Adjust cut to avoid overcut: to “NO” and Press “OK”
8. Select “Text Items” and Press “OK”
9. Press “F1” and Uncheck each Item checked
10. Press “F1” to select “Cut/Fill Center” , “Offline (3D)” (select in order)
11. Press “F3” Split View
12. Press “F1” and Uncheck each Item checked
13. Press “F1” to select “Cut/Fill Center” , “Offline (3D)” (select in order)
14. Press “F4” Text View 1
15. Press “F1” and Uncheck each Item checked
16. Press “F1” to select “Design Name” , “Design Elev.(3D)”,“Design XSlope (3D)”,
”V. GNSS Err (3D) and GNSS Acc. Mode (select in order)
17. Press “F5” Text View 2
18. Press “F1” and Uncheck each Item checked
19. Press “F1” to select “Northing (3D)”,“Easting (3D)”,“Elevation (3D)”,“Bucket
Slope” and “Offline (3D)” (select in order)
4

20. Press “OK”
21. Select Beeper and Press “OK”
22. Press “F1” and Uncheck each Item checked
23. Press “F1” to select On Grade and Below Grade
24. Press “OK”
25. Select “Save Settings” and Press “OK”
26. Select “Display Settings” and Press “OK”
27. Enter Operator’s Name such as “Joe G” and Press “OK”
28. Press “ESC” twice to return to operating screen
5

Field Reference Guide
SITECH TECHNOLOGY DEALER
GCS900 Check Bucket Wear
Version: 13.1
1. Press “Menu”
2. Select “Bucket Wear” and Press “OK”
3. Measure J to J1
4. Enter Distance and Press “OK”
5. Press “ESC” to return to operating screen
6

Field Reference Guide
SITECH TECHNOLOGY DEALER
GCS900 Load Design
Version: 13.1
1. Press “Menu”
2. Select “Select Design” and Press “OK”
3. Use Arrows to highlight Design and Press “OK”
4. Press “ESC” to return to the operating screen
7

Field Reference Guide
SITECH TECHNOLOGY DEALER
GCS900 Verify HEX System Accuracy
Version: 13.1
Verify the system accuracy by checking into Bench Point
1. Move machine to Bench Point
2. Position Bucket Tip over Bench Point
3. Press “Next” until Text Screen 2 is displayed
4. Verify correct Bucket Tip is selected
5. Verify Northing, Easting and Elevation are correct (add distance above Bench Point)
6. See Supervisor if Northing and Easting do not match
7. See Supervisor if Elevation does not match and Press
8

Field Reference Guide
SITECH TECHNOLOGY DEALER
GCS900 HEX Sensor Accuracy Test
Version: 13.1
1. Place Bucket in vertical position with teeth pointing down on a point on a solid surface
2. Record Cut/Fill
3. Uncurl Bucket and position Boom and Stick so teeth touch the same point
4. Verify Cut/Fill
5. Curl Bucket and positon bucket so teeth touch the same point
6. Verify Cut/Fill
(See Supervisor if Elevation is off by more than 0.2’ or 70mm)
9

Field Reference Guide
SITECH TECHNOLOGY DEALER
GCS900 HEX Vertical Offset
Version: 13.1
1. Press “F4” to enter Horizontal and Vertical Offset
2. Press “F6” until Vertical Offset is displayed at the top left of screen
3. Enter Vertical Offset and Press “F2” to select above or below Design
4. Press “OK” to return to operating screen
5. Vertical Offset is displayed at the bottom of the screen
10

Field Reference Guide
SITECH TECHNOLOGY DEALE
R
GCS900 HEX Horizontal Offset
Version: 13.1
1. Press “F4” to enter Horizontal and Vertical Offset
2. Press “F6” until Horizontal Offset is displayed at the top left of screen
3. Press “F1” Alignment:
4. Use Arrows to Select [Plan Line] if list is displayed and Press “OK”
5. Use Arrows to position cross-hair over Line and Press “F1” Select
11

6. Press “OK” and enter Offset distance
7. Press “F2” Select Offset to be Left or Right of the line (-3.00 is Left)
8. Press “OK” to return to operating screen
9. Horizontal Offset is highlighted in red
10. Press “F1” to change Bucket Left, Right or Center
12