SI Solo 3 User manual

INSTALLERS: Please leave this manual with the owner.
Solo 3
Indoor
375 External
Installation Instructions
®
400196 Ι v. 1.2 Ι May 2023

Scan the QR code to view the SI warranty for this product.
Technical Support: 512.832.6939 screeninnovations.com
Hours of Support: 7:30am – 5pm CST [email protected]
Please use this QR Code to access the updated installation instructions and related
documents.

TABLE OF CONTENTS
Parts in the Box .............................................................................4
Spacer Blocks (Optional) ....................................................................5
Installation – Solo 3 375 External – Indoor ..................................................6 – 12
Power Options ............................................................................8 – 11
AC, Low Voltage (DC), and Control – Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Setting Up Wired Screen Using Moab ...........................................9–10
Wire Considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
References ................................................................................. 13
Servicing Solo 3 375 External – Indoor......................................................14–22
Inspecting the Roll ..............................................................14–15
Tube Removal...................................................................16–17
Tube Installation ................................................................18–21
Wireless Sleep Mode .............................................................22

4
Included in the box with hardwired control screens only
Note: Use appropriate fasteners based on structure on-site
Moab Control Board
(1 per 485 screen)
Parts in the Box – Solo 3 375 External – Indoor
Screen Wall Brackets
Spacer Blocks
(Optional – 4 per screen)
RJ45 Coupler
(AC – 485 screens only)
Din Rail
(AC – 485 screens only)
Terminal Blocks, Bracket,
and DUOCoup
(per low voltage and/or 485)
PARTS IN THE BOX
375 Box
RF Remote
(1 per RTF screen)
Included remotes’ form factor may
vary, however functionality and
performance is consistent.
IR Remote

5
Spacer Blocks – Used to clear an obstruction in the screen or screen material path.
Before installing, connect spacer blocks to screen brackets.
NOTE: Do not use more than four (4) spacer blocks per bracket.
SPACER BLOCKS (OPTIONAL)
Spacer Blocks

6
2–4” 2–4”
2. The recommended position for the box bracket is 2–4” from the end caps.
NOTE: Installing the wall brackets as close to the end of the cassette as possible ensures better
stability of the screen.
1. Terminate pre-wire with the supplied terminal block.
Data For 485 Only
Header
+ 24 VDC
- 24 VDC
Data +
Data -
Data ground
V+
V-
+
-
G
Jamb
INSTALLATION – SOLO 3 375 EXTERNAL – INDOOR
Installation – Solo 3 375 External – Indoor

7
3. To install the screen, start with the wall bracket lever pointed down in the unlocked position.
4. Ensure the terminal blocks are plugged in and installed in the brackets.
Proper position for installing Box
INSTALLATION – SOLO 3 375 EXTERNAL – INDOOR
Installation – Solo 3 375 External – Indoor
Data Cable
Power
Cable
NOTE: Refer to the next page to see the
wiring as per your power.
Data Cable
Power
Cable110v/220v AC
24v DC
24v DC

8
AC, LOW VOLTAGE (DC), AND CONTROL – WIRING
AC Wiring (AC Motor – Wireless Control)
DC Wiring (110 or 220v) AC
(Motor – Wired Control)
DC Wiring (24v) DC
(Motor – Wireless Control)
DC Wiring (DC Motor – Wired Control)
AC, LV (DC) Wiring
Marking
V+
V-
+
-
G
Description
Positive 24VDC
Negative 24VDC
485 Data Positive
485 Data Negative
485 Data Ground
24v DC Power Supply
RS485 Data+
RS485 Data-
RS485 Ground
Pigtail Load (Black/Brown)
Neutral (White/Blue)
Ground (Green/Yellow)
Length of wire: 6’
*These colors on left are for USA,
international are on the right
Pigtail
Load (Black/Brown)
Neutral (White/Blue)
Ground (Green/Yellow)
RS485 (+) - White
RS485 (-) - Orange
-
Power 7v DC - Red
-
-
-
Ground - Brown
Pin 1
Pin 8
1a. Connect charger (Preferred)
1b. Optionally if you dont
have charger, just depress
the Motor button
thin tool

9
Setting up Wired Screen Using Moab
DC Wire Diagram Illustrating Inital Setup
5. If the screen is wired with wired communication or 485 control, it will include a motor control board,
Moab. This control board allows for setting limits and/or controling the screen. Typically, this board is
located in the head end/equipment location. See the wiring chart on page 11 to determine maximum
wire length.
6. Upper and lower limits are already factory-set. Once all connections are made including the power
supply, you may now adjust the lower limits using the Moab control board.
SETTING UP WIRED SCREEN USING MOAB
Scan the QR code for complete details on how to install and program using
Moab.
485 MOTORS
485 MOTORS
ONLY
ONLY
485
485
DEVICES ONLY
DEVICES ONLY
3
3
8
8
8
8
UP
UP
6
6
8
8
USER
USER
ACT
ACT
MODES
MODES
1 2 3 4
1 2 3 4
485 BUS
485 BUS
8
8
6
6
5
5
1
1
&
&
IR REC
IR REC
ACTIVE
ACTIVE
L12
L12
L11
L11
L9
L9
L15
L15
L14
L14
L13
L13
L1
L1
L3
L3
L2
L2
L4
L4
L7
L7
L8
L8
302325
302325
202311 (EXT)
202311 (EXT)
202312 (INT)
202312 (INT)
VIEW
VIEW
VIEW
VIEW
485
485
LIMIT
LIMIT
LOWER
LOWER
LIMIT
LIMIT
MOTOR ROTATION
MOTOR ROTATION
STANDARD REVERSE
STANDARD REVERSE
9VDC
9VDC
485
485
DC MOTOR
DC MOTOR
485 PAIRING
485 PAIRING
STOP
STOP
UPPER
UPPER
IR REC
IR REC
IR
IR
LED
LED
BOARD
BOARD
SETTINGS
SETTINGS
6
6
3
3
(T)
(T)
-
-
STOP
STOP
485 DEVICE &
485 DEVICE &
DRY CONTACT PORT
DRY CONTACT PORT
3.5mm(1/8 in) mono (TS)
3.5mm(1/8 in) mono (TS)
(S)
(S)
+
+
RJ45 RJ9
RJ45 RJ9
12-28VDC
12-28VDC
DC POWER &
DC POWER &
485 DATA PORT
485 DATA PORT
DOWN
DOWN
AC MOTOR
AC MOTOR
G D- D+ V- V+
G D- D+ V- V+
3
3
6
6
2
2
4
4
5
5
7
7
8
8
1
1
V- V+
V- V+
12-28VDC
12-28VDC
D+
D+
D-
D-
G
G
12v TRIGGER PORT
12v TRIGGER PORT
PROG
PROG
BUTTONS
BUTTONS
DOWN
D O W N
485 NETWORK
485 NETWORK
MV
MV
STOP
STOP
ON
ON
LED1
LED1
S4
S4
S3
S3
S2
S2
LED15
LED15
LED14
LED14
LED13
LED13
LED12
LED12
LED11
LED11
LED9
LED9
LED8
LED8
LED7
LED7
LED4
LED4
LED3
LED3
LED2
LED2
IC3
IC3

10
7. Once all adjustments are made and nalized, the Moab may now be placed in a convenient location for
the install. Third party control such as Dry Contact closures, 12v Triggers, Serial Connections,
and Infrared may now be integrated with Moab.
SETTING UP WIRED SCREEN USING MOAB
Scan the QR code for complete pinout and third party integration details using
Moab.
485 MOTORS
485 MOTORS
ONLY
ONLY
485
485
DEVICES ONLY
DEVICES ONLY
3
3
8
8
8
8
UP
UP
6
6
8
8
USER
USER
ACT
ACT
MODES
MODES
1 2 3 4
1 2 3 4
485 BUS
485 BUS
8
8
6
6
5
5
1
1
&
&
IR REC
IR REC
ACTIVE
ACTIVE
L12
L12
L11
L11
L9
L9
L15
L15
L14
L14
L13
L13
L1
L1
L3
L3
L2
L2
L4
L4
L7
L7
L8
L8
302325
302325
202311 (EXT)
202311 (EXT)
202312 (INT)
202312 (INT)
VIEW
VIEW
VIEW
VIEW
485
485
LIMIT
LIMIT
LOWER
LOWER
LIMIT
LIMIT
MOTOR ROTATION
MOTOR ROTATION
STANDARD REVERSE
STANDARD REVERSE
9VDC
9VDC
485
485
DC MOTOR
DC MOTOR
485 PAIRING
485 PAIRING
STOP
STOP
UPPER
UPPER
IR REC
IR REC
IR
IR
LED
LED
BOARD
BOARD
SETTINGS
SETTINGS
6
6
3
3
(T)
(T)
-
-
STOP
STOP
485 DEVICE &
485 DEVICE &
DRY CONTACT PORT
DRY CONTACT PORT
3.5mm(1/8 in) mono (TS)
3.5mm(1/8 in) mono (TS)
(S)
(S)
+
+
RJ45 RJ9
RJ45 RJ9
12-28VDC
12-28VDC
DC POWER &
DC POWER &
485 DATA PORT
485 DATA PORT
DOWN
DOWN
AC MOTOR
AC MOTOR
G D- D+ V- V+
G D- D+ V- V+
3
3
6
6
2
2
4
4
5
5
7
7
8
8
1
1
V- V+
V- V+
12-28VDC
12-28VDC
D+
D+
D-
D-
G
G
12v TRIGGER PORT
12v TRIGGER PORT
PROG
PROG
BUTTONS
BUTTONS
DOWN
D O W N
485 NETWORK
485 NETWORK
MV
MV
STOP
STOP
ON
ON
LED1
LED1
S4
S4
S3
S3
S2
S2
LED15
LED15
LED14
LED14
LED13
LED13
LED12
LED12
LED11
LED11
LED9
LED9
LED8
LED8
LED7
LED7
LED4
LED4
LED3
LED3
LED2
LED2
IC3
IC3
Setting up Wired Screen Using Moab