SICO ROOM MAKER Series User manual

BEFORE YOU BEGIN ...
IMPORTANT: It takes two people to safely assemble
the system – do not try to do it by yourself.
Please read and understand the instructions before you
start to assemble.
Installing the bed in a finished recess is similar to hanging
a steel door – if the frame is true and square, you are unlikely
to have any problems. Make sure that all measurements are
correct and that the recess is plumb, level, and square.
This bed must be securely anchored to the floor.
Failure to follow instructions may cause the
baseplate or hinges to release, which could cause
serious injury.
INSTALLATION
INSTRUCTIONS
ROOM MAKER®
WALL BED
Printed in USA (04/05) ® SICO and Room Maker are registered trademarks of SICO Incorporated. Part No. 102472 Rev. C
IMPORTANT: Before you start to
install the bed, refer to the table and
verify the size of the recess opening.
The SICO bed is designed to be in-
stalled in either a 22" or an 18-5/8"
deep recess. However, if heavy blan-
kets, quilts, or other bedding will be
used, or if pillows will be stored on
the bed, SICO recommends setting
up the bed at the 22" depth only.
VERIFY SIZE OF RECESS
If you have any problems when installing,
contact SICO Customer Service at
1-800-424-0796
Opening
Height
Opening
Width
Recess
Depth
OPENING OPENING RECESS
BED STYLE BED SIZE HEIGHT WIDTH DEPTH
END FOLD Twin Regular 83-1/2" 41" 18-5/8"or 22"
(2121 mm) (1041 mm) (473 or 559 mm)
Twin Extra Length 88-5/8” 41" 18-5/8" or 22"
(2251 mm) (1041 mm) (473 or 559 mm)
Double Regular 83-1/2" 56" 18-5/8" or 22"
(2121 mm) (1422 mm) (473 or 559 mm)
Double Extra Length 88-5/8" 56" 18-5/8" or 22"
(2251 mm) (1422 mm) (473 or 559 mm)
Queen 88-5/8" 62-1/2" 18-5/8" or 22"
(2251 mm) (1588 mm) (473 or 559 mm)
King 88-5/8" 79" 18-5/8" or 22"
(2251 mm) (2007 mm) (473 or 559 mm)
SIDE FOLD Twin Regular 49" 77" 18-5/8" or 22"
(1245 mm) (1956 mm) (473 or 559 mm)
Twin Extra Length 49" 83" 18-5/8" or 22"
(1245 mm) (2108 mm) (473 or 559 mm)
Double Regular 64" 77" 18-5/8" or 22"
(1626 mm) (1956 mm) (473 or 559 mm)
Double Extra Length 64" 83" 18-5/8" or 22"
(1626 mm) (2108 mm) (473 or 559 mm)
Queen 70-1/2" 83" 18-5/8" or 22"
(1791 mm) (2108 mm) (473 or 559 mm)
WARNING

A - Bed Frame Width
D - Finished Recess Opening Width 22" (559mm)
Cabinet Depth
B - Installed Height of Bed
E - Finished Recess Opening Height
22" (559mm)
Cabinet Depth
C - Extends Beyond Recess
218"
(54mm)
Rear
Wall
Rear
Wall
Bed Raised Bed Raised
Bed Lowered

2
TOOLS REQUIRED
UNPACKING
•Phillips screwdriver
•Large flat-blade screwdriver
•Utility knife
•Electric drill (3/8")
•A1" drill bit may be required
(see page 5)
•Rotary hammer drill and
1/2" bit – optional
•Masonry bit (if attaching
to masonry floor or wall);
size of bit depends on
floor type - refer to
pages 4 - 5
• Tape measure
• Pencil
• Carpenter's level
• Hammer
• Vise-grip pliers
• Pliers
•Ratchet wrench
•9/16" and 3/4" deep
sockets
•6" socket extension
•Open-end wrenches:
7/16" (qty 2); 9/16"; 3/4";
15/16".
1. Remove the steel bands and open the carton.
2. Remove the main frame and place it on the floor with
the face panel facing down (be sure there is nothing
on the floor which could scratch the bed face).
If the bed was ordered without a factory-finished
face panel on the main frame, you can attach panel-
ing or other covering either while the frame is still on
the floor or after the bed is in the recess. Refer to
the separate instructions which are included in the
small parts pack.
3. King bed frames are shipped in two sections which
must be bolted together. Refer to page 7 for an
illustration of the parts.
4. Unpack the headboard, padboard, baseplate,
mattress strap, handle package, and any other items
which may be stapled to the carton. Refer to the
illustration below, or to the Parts List drawing on
page 17, to identify the various parts.
5. Open the separate carton which contains the power
packs (hinge weldments and spring tubes) and the
headboard supports.
Linkage
Assembly (2)
Padboard
Bed
Frame
Headboard
Headboard
Support
Spring Tube
Assembly (2)
Headboard
Adjustment
Bolts
Hinge Weldment
Power Pack
Baseplate Hinge Spring
Adjustment Nut
(2 each unit)
Hinge Weldment
Carriage Bolt
(4 each unit) Baseplate
Anchor Bolt (6)
For King (9)
Cam (2)
Plunger
5/8" Lock Nut
NOTE: King beds have a
third power pack, cam,
and linkage in the center.
To avoid damaging the unit, do not walk
on the bed’s face panel!
CAUTION

SECURE BASEPLATE TO FLOOR
3
IMPORTANT: If you have not
already done so, verify the recess
opening with the chart on the
front page.
If heavy blankets, quilts, or other
bedding will be used, or if pillows
will be stored on the bed, SICO
recommends setting up the bed
at the 22" depth ONLY.
1. Check that the baseplate fits into
the recess:
a. If the baseplate is narrower
than the recess, center it (side
to side) in the recess opening.
b. If the baseplate is wider than
the recess, be sure that the
recess was properly construct-
ed. The recess opening should
be 1/2" wider than the bed
frame. Refer to the chart on
the front page.
2. If there is a floor molding or
base-board which is more than
1/8" thick, remove it.
3. Position the rear edge of the
baseplate 18-1/4" from the front
edge of the verticals. Check both
ends.
4. Secure the baseplate to the floor,
following the appropriate floor
anchoring instructions on the
next three pages.
Anchor Bolt
Hole (6)
For King (9)
Anchor Bolt
Hole (6)
For King (9)
Carriage
Bolt (8)
For King (16)
Carriage
Bolt (8)
for King (12)
18-1/4" 18-1/4"
NOTE: Rear edge of baseplate
must be 18-1/4" from front edge
of recess. Check both ends.
NOTE: Rear edge of baseplate
must be 18-1/4" from front edge
of recess. Check both ends.
22" DEEP RECESS
18-5/8" DEEP RECESS
18-1/4" 18-1/4"
SECURING THE WALL ATTACHMENT KIT
See the ROOM MAKER WALLBED
Wall Attachment instruction manual
(part number 117787) for complete
instructions on how to attach the bed
to the wall.

SECURE BASEPLATE TO FLOOR (continued)
4
If the bed must be securely anchored to the floor
Failure to follow instructions may cause the
baseplate to release, which could cause serious
injury.
FLOOR ANCHORING –
Hard Concrete Slab Floors
NOTE: Anchors for hard concrete
slab floors are provided with the
bed. Use six (6) anchors per bed,
use nine (9) anchors for the king
bed. Use anchors appropriate to
the type of floor: SICO recom-
mends Red-Head #HN-1230 1/2 x
3" Expansion Anchors, or their
equivalent.
1. Have the baseplate in position
before installing anchors.
2. At the first anchor location, drill a
1/2" diameter hole straight down
through the baseplate and at least
2-3/4" into the concrete. You may
have to drill a 1/4" diameter pilot
hole, then enlarge it to 1/2".
Do not allow the drill to rotate and
hammer on the hard aggregate,
or the hole may become enlarged.
If this happens, refer to the proce-
dure for “Lightweight Concrete
Floors” on page 5.
3. Install the washer onto the anchor
bolt (see note above), then install
the nut one turn.
Drive the anchor into the hole.
IMPORTANT: The anchor must
extend at least 2-1/4" into the
concrete.
4. Tighten the nut on the anchor. If you
don’t feel firm resistance on
the wrench, the anchor isn’t seat-
ing or locking properly (the floor
may be lightweight concrete –
see page 5).
If the anchor bolt didn’t tighten, or
if you met an obstacle such as a
reinforcing bar, drill a new hole
through the baseplate and into the
concrete, 1-1/2" away from the
existing hole.
5. Repeat steps 2 through 4 for the
other anchors.
IMPORTANT: Score / cut
carpet before drilling for
anchors. This will prevent
the carpet from fraying.
Especially on plush carpet,
be sure the baseplate is
pulled down tightly to the
floor.
Do not continue with the
bed installation unless all
anchors are properly
installed and tightened.
NOTICE: SICO does not
recommend using power-
driven or nonexpanding-
type anchor bolts (those
forced in with compressed
air or an explosive charge)
to secure the baseplate to
the floor.
Anchors and washers are in
the Small Parts Package
marked “102082.”
If you encounter any
problem or a unique floor
construction, contact SICO
Customer Service at
1-800-424-0796.
WARNING
Drill 1/2” dia.
hold into floor
Drive anchor
bolt into hole
Tighten nut
on anchor
Baseplate
3-1/2”
Minimum
WARNING
DO NOT floor mount the bed on top of
post tension concrete. If you are unsure
of the concrete, have the floor x-rayed or
check with the architect. Serious injury
and damage to the unit can occur.

SECURE BASEPLATE TO FLOOR (continued)
5
If the bed must be securely anchored to the floor
Failure to follow instructions may cause the
baseplate to release, which could cause serious
injury.
FLOOR ANCHORING –
Wood, Lightweight Concrete,
Thin Concrete Over Wood,
Metal Deck, and Miscellaneous
Floors
NOTE: Use anchors appropriate
to the type of floor: SICO
recommends the Star 3/8 x 6"
round-head toggle bolts which
are supplied with the bed (or
their equivalent). Use six (6)
anchors per bed, use nine (9)
anchors for the king bed.
1. Have the baseplate in position
before installing anchors.
2. At the first anchor location, drill a
1" diameter hole through the
baseplate and floor.
If you encounter a joist, or if a
wood floor won’t support any
type of anchor, follow the proce-
dure under “Joists,” page 6.
3. Assemble a 1-1/2" diameter
washer onto a 3/8" diameter
toggle bolt.
Insert the toggle bolt through
the hole.
4. Repeat steps 2 and 3 for the
other anchors.
5. Tighten the toggle bolts with a
flat-blade screwdriver.
IMPORTANT: Score / cut
carpet before drilling for
anchors. This will prevent
the carpet from fraying.
Especially on plush carpet,
be sure the baseplate is
pulled down tightly to the
floor.
Do not continue with the
bed installation unless all
anchors are properly
installed and tightened.
If you encounter any
problem or a unique floor
construction, contact SICO
Customer Service at
1-800-328-6138.
Baseplate
Thin Concrete
Wood Floor
Baseplate
Wood Floor
Toggle Bolt
WARNING
WARNING
DO NOT floor mount the bed on top of
post tension concrete. If you are unsure
of the concrete, have the floor x-rayed or
check with the architect. Serious injury
and damage to the unit can occur.

SECURE BASEPLATE TO FLOOR (continued)
6
If the bed must be securely anchored to the floor
Failure to follow instructions may cause the
baseplate to release, which could cause serious
injury.
FLOOR ANCHORING –
Joists
If you encounter a joist at the
anchoring location, use the following
procedure. Note that toggles are
preferred for anchoring the
baseplate, so the following procedure
should be used only if unavoidable.
NOTE: Floor anchors for wood
joists are not provided with the
bed. Use six (6) 1/2 x 5" hex-head
lag screws (available from any
hardware store), use nine (9) for
the king bed.
1. Have the baseplate in position
before installing anchors.
2. At the first anchor location:
Floors of Lightweight Concrete
Over Wood. Drill a 3/8" diameter
pilot hole through the baseplate
and concrete. Then drill a 7/32"
diameter pilot hole into the joist.
Wood Floors. Drill a 7/32"
diameter pilot hole through the
baseplate and floor, into the joist.
3. Use a 1/2" diameter lag screw
and large washers. The screw
must be long enough so that at
least 2" of it penetrates the joist.
Install the lag screw and tighten
it down securely.
4. Repeat steps 2 and 3 for the
other anchors.
IMPORTANT:
Score / cut carpet before
drilling for anchors. This
will prevent the carpet from
fraying.
Especially on plush carpet,
be sure the baseplate is
pulled down tightly to the
floor.
Do not continue with the
bed installation unless all
anchors are properly
installed and tightened.
If you encounter any
problem or a unique floor
construction, contact SICO
Customer Service at
1-800-328-6138.
Baseplate
Thin Concrete
Wood Floor
Baseplate
Wood Floor
Joist
Joist
WARNING

ATTACH BED HALVES TOGETHER (King Bed Only)
7
King bed frames are shipped in
two halves, which must be bolted
together using a center plate.
1. Slide the two frame halves
together (see below).
2. Attach the center plate (finger-
tight only) to the rear of the bed-
frame as shown, using four
1/2-13 x 2" bolts, lockwashers,
and hex nuts.
3. Install the rubber corners on the
front end rail. Attach the two
frame halves together, and
attach the end rail to the front
end of the frame, using 3/8-24 x
2" bolts and lock nuts (also
finger-tight).
4. Tighten all fasteners securely –
in the following sequence:
a. Center plate.
b. Front end rail.
c. Frame halves.
Hardware for assembling
the frame halves and
attaching the center plate
are in the bag marked
“102474.”
Center
Plate
Center
Plate
Rubber Corner
3/8" Lock Nuts
End Rail
3/8" Lock Nuts
This cam and
cable not used
on all units
1/2"-13 x 2" Bolts, Nuts,
& Lockwashers (4 of each)
3/8" x 2"
Bolts (5)
REAR
RIGHT
SIDE
LEFT
SIDE
FRONT

ATTACH POWER PACKS
8
1. If you have purchased a bed with
no face, you should install the
bed face panel now. See the
instructions in the small parts
package marked “101866.”
2. Move the bed frame about 2 ft
from the recess opening, aligned
with the recess.
3. Attach the two headboard sup-
ports to the cams on the bed
frame (see also the illustration
on page 2):
NOTE: For king beds, there is an
additional right-hand headboard
support. Attach it to the center-
cam.
a. Remove the two outside 1/2"
diameter locknuts and washers
from each cam. Don’t loosen
or remove the two inside nuts.
b. Install the headboard support
over the threaded bolts.
c. Reattach the lockwashers and
nuts, and tighten them securely.
4. The two power packs (spring tube
assemblies mounted on hinge
weldments – see the illustration
on page 2), are shipped in a
separate carton.
NOTE: King beds have a third
power pack.
To prepare the unit for installing
the power packs:
a. Remove the 5/8" lock nut from
the end of each cable.
b. Pull the plunger out of the end
of each spring tube assembly.
c. Remove the cotter pin and hinge
pin from each cam.
Recess
Bed
Cam
2 ft
Hinge
Pin
Cotter
Pin
Locknut and
Lockwasher
Right-Handed
Headboard
Support
RIGHT-HAND SIDE SHOWN

ATTACH POWER PACKS (continued)
9
5. Attach each power pack to its cam
by inserting a hinge pin and
securing with a cotter pin.
NOTE: The spring is coated with
grease. Don't allow it to drop out
of the spring tube.
a. Reinstall the plunger in the end
of the spring tube. If the spring
end is not flat (A), install the
plunger with its lugs toward the
spring; if the spring end is flat
(B), install the plunger with its
lugs away from the spring.
Lugs are different heights to
match different springs.
b. Secure the plunger by loosely
reattaching the 5/8" nut on the
end of the cable.
It makes no difference
which side of the bed each
spring is installed on –
even if they are different
colors.
IMPORTANT!
Make sure the plunger is
sitting FLAT on the
spring.
c. Using a 9/16 open-end wrench
or vise-grip pliers, grasp the
cable as shown. Turn the locknut
on the cable thread until at least-
four threads are visible past the
plastic insert on the locknut.
A B
Hinge Pin
Cotter Pin
Lug
Lug

ATTACH POWER PACKS (continued)
10
Carriage
Bolts
6. Remove the nuts and washers
from the carriage bolts in the
baseplate (12 bolts in a king-size
baseplate, 8 bolts in others).
7. Slide the bed frame approximately
1" into the recess.
8. With one person inside the recess
and one outside, lift the bed to its
vertical position.
Slip the hinge weldments onto
the carriage bolts in the baseplate,
and fasten them loosely with
1-1/2" O.D. washers and hexnuts.
IMPORTANT: Do not fully tighten
the hex nuts yet.

ALIGN BED FRAME IN RECESS
11
1. Attach the handles to the bed
frame, using two 1/4" dia. x 2-1/2"
machine screws in each handle.
2. Position the bed frame so there
is an equal gap (about 1/4") be-
tween the frame and the recess on
both sides, at the bottom.
3. Insofar as possible, you want to
position the bed so the frame is
flush with the front edge of the
recess. As a starting point,
maneuver the frame so it is flush
with the recess on both sides at
the bottom.
4. Check the top of the frame. If
necessary, move the bottom in or
out on each side until the top is
flush on both sides.
NOTE: Because of small cumula-
tive variations in the recess, wall,
and floor, you may not be able to
keep the bottom of the frame
flush with the recess.
Recess
Recess
Step 2:
Equal gaps
here.
Step 4:
Flush here.
Bed Frame
Bed Frame
and
Step 3:
Flush here.
and

ALIGN BED FRAME IN RECESS (continued)
12
5. Tighten the nuts on the two REAR
carriage bolts, to secure each
hinge weldment to the baseplate.
6. If the top gap (between the bed
frame and the recess header) is
not even:
a. Determine which is the high
side (the side with the least
gap between the frame and
header).
b. On that same side, install and
tighten the two front nuts and
washers which secure the
hinge weldment to the base-
plate.
c. On the low side (the side with
the most gap between the
frame and header), screw in
both height adjustment hex bolts
until the top gap is the same
on both sides. Be sure to
turn both low-side adjustment
bolts by the same amount.
d. If the baseplate is installed on
carpet, turn both height adjust-
ment bolts an additional half
turn to compensate for later
settling.
7. Install and tighten the front nuts
and washers which hold the other
hinge weldment(s) to the base-
plate.
Rear
Carriage Bolts
Recess
Step 6:
Equal gaps
here.
Bed Frame
Front Nuts
& Washers
Height Adjustment
Bolts

ATTACH BOXSPRING AND MATTRESS
13
1. Turn the boxspring on edge.
Using #8 x 3/4" screws, attach
the mattress strap to the side
framing member (wood) on the
underside of the boxspring, about
9" in from the foot end. Keep the
strap snug.
2. Bring the bed down to the floor,
and place the boxspring and
mattress on the frame to hold the
bed down. For the time being,
position the mattress so there will
be clearance for installing the
headboard and padboard.
3. There are two clips (one on a twin
bed) at the foot of the bed, that
are used to secure the boxspring
to the bed frame.
Install the clip screws through the
clips and into the wooden framing
members on the foot of the box-
spring.
4. Move the mattress into position
on the boxspring. Wrap the long
end of the mattress strap snugly
around the mattress as shown,
and attach it to the Velcro on the
short end.
Boxspring framing
member must be
high enough for
screw to engage.
Bed
Frame
Bed Frame
Bed Frame
Boxspring
Clip
#8 x 3/4" screw
must go into
upper hole in clip.
Boxspring Mattress
Boxspring
Mattress
Strap
END VIEW
END VIEW
Velcro
CAUTION: The bed will
be difficult to pull down
because the springs are
being compressed. Do
not let go of the bed frame
until the boxspring and
mattress are installed.
SIDE VIEW
CAUTION

ATTACH HEADBOARD/PADBOARD ASSEMBLY
14
1. Attach the padboard to the head-
board, using the pre-attached
screws and hinges.
The padboard is shipped with the
linkage mounting brackets in-
stalled for use in a 22" recess.
If installing the bed in an 18-5/8"
recess, move the brackets to the
predrilled higher set of holes
(using the same fasteners).
2. Attach the linkage assemblies to
the padboard brackets and to the
hinge weldments. For a 22"
recess, attach as shown, with the
12" sections toward the padboard.
For an 18-5/8" deep recess:
a. Move the padboard brackets
(see step 1).
b. On both linkage assemblies
(three on a king bed), discon-
nect the two linkage sections
(15" and 12") from the pivot
plate. Switch their positions,
and reinstall them so the 15"
section is attached to the pad-
board and the 12" section to
the hinge weldment.
CAUTION: Don’t over-tighten
the locknuts, or the linkages
won’t pivot. Tighten just until
the parts are snug.
3. Attach the assembled padboard/
headboard to the support brackets
on the bed frame:
CAUTION: Don’t step on the
end of the bed face.
a. Use the upper two slots for a
22" deep recess.
b. Use the lower two slots for an
18-5/8" deep recess.
Headboard
Padboard
Padboard
Linkage
Mounting
Bracket
12" Linkage
Section
Pivot Plate
(90° notch
facing up)
15" Linkage
Section
Bracket
Support
Slots for
22" Recess
Slots for
18-5/8" Recess
LINKAGES ARE SHOWN
CONNECTED FOR A
22" RECESS
Shown for 22" recess.
Move brackets to other hole
locations for 18-5/8" recess.
For either recess depth,
the 90° notch on the pivot
plate must face up (that is,
toward the white pad on
the linkage mounting
bracket).
If the pivot plate is
installed upside down, the
hinge will bend or break
when the bed is raised.
CAUTION

MAKE FINAL ADJUSTMENTS
15
1. Do not try to adjust the bed until:
a. The boxspring and mattress
are secured to the bed frame;
and
b. Any desired bed face or panel
is installed.
The combined weight of the face
and bedding is what counteracts
the hinge springs when the bed is
lowered to the floor.
2. Before raising the bed, loosen the
headboard adjustment bolts until
1/4" of thread extends beyond the
nut (top illustration).
Then adjust the bolts until the bed
frame is flush with the edge of the
recess. Turn in direction Yto
move the frame out of the recess,
or direction Xto move it into the
recess. Adjust both bolts equally.
IMPORTANT: If the bed frame
is not flush with the recess,
repeat this adjustment – do
not adjust the spring tube.
3. The finished bed (with blankets or
other covers installed) should
require only a minimum of “lift” to
begin folding it up. Also, when first
installed, it should rest 2 - 4"
above the floor. If not:
a. Bed won't stay near the floor.
Turn the 1/2-13 lock-nuts on the
spring tube mounting bolts
counterclockwise (direction A).
Adjust all four nuts equally, and
make only 1/2 turn on each nut.
Repeat until the bed operates
properly.
b. Bed is too heavy to lift. Turn
the 1/2-13 locknuts on the
spring tube mounting screws
clockwise (direction B). Adjust
all four nuts equally until the bed
operates properly.
NOTE: After the bed has been
in use for some time, it will
gradually settle to the floor.
4. The bed is now ready for use.
If the bed doesn’t operate
properly after the above
adjustment, contact SICO
Customer Service. When
calling, please have the
bed size and serial number,
and the dot colors on the
spring tube.
The lift adjustment may
have to be repeated
periodically until the
bed has been in use for
some time.
At least one full thread
must be visible on the
end of the bolt. If you
remove the nuts from
the bolts when the bed
is down, the spring
will release suddenly –
which could result in
serious injury.
Spring Tube
Mounting Bolt
BED/RECESS POSITIONING ADJUSTMENT
BED “LIFT” ADJUSTMENT
Spring tube weldment
must be centered
in hinge weldment
1/4" (before you
begin adjustment)
Colored
Dot
B
A
Headboard
Adjustment Bolt
Y
X
Be careful where you
place your fingers until
the bed is adjusted.
The bed frame could
pinch your fingers if it
folds too far into the
recess.
WARNING
WARNING

PARTS LIST
16
ITEM
NO. DESCRIPTION
1Frame
2Pad, linkage connector
3Pin, dowel
4Baseplate assembly
5Headboard assembly
6Padboard assembly
7Cable
8 Spring [#]
9Linkage assembly
10 Washer, 7/16" ID x 1-112" OD x 1/8"
11 Plunger
12L Support, headboard, LR
12R Support, headboard, RH
13 Cam
14 Screw, cap, 1/4-20 x 7/8"
15 Tube, spring
16 Locknut, 1/2-13
17 Bracket, mounting
18 Pin, hinge
19 Handle (SPECIFY: color)
20 Screw, machine, 1/4" dia. x 2-1/2"
21 Corner, rubber
22 Washer, 1/2"
23 Pin, cotter
24 Screw, #8 x 3/4"
25 Screw, cap, 1/2-13 x 3-1/2"
26 Bolt, anchor, 1/2-3/8 x 3"
27 Locknut, 1/4-20
28 Lockwasher, 1/2"
29 Nut, 1/2-13
30 Bolt, carriage, 3/8" x 1-3/4"
31 Hinge
ITEM
NO. DESCRIPTION
32 Bolt, carriage, 1/4-20 x 1-1/4"
33 Screw, cap, 1/2-13 x 3"
34 Hinge weldment
35 Clip, boxspring [early models only]
36 Nut, hex, 3/8-16
37 Locknut, 5/8-11
38 Strap, mattress (SPECIFY: bed size)
40 Screw, cap, 3/8-24 x 2"
41 Nut, hex, 1/4-20
42 Cap, end (SPECIFY: chrome or brass)
43 Rail, end (SPECIFY: chrome or brass)
44 Rail, side, RH (SPECIFY: chrome or brass)
45 Rail, side, LH (SPECIFY: chrome or brass)
46 Frame, side-fold bed
47 Baseplate assembly, side-fold bed
48 Headboard assembly, side-fold bed
49 Padboard assembly, side-fold bed
50 Frame, RH, king bed
51 Frame, LH, king bed
52 Rail, end, king bed
53 Bolt, 3/8 x 2"
54 Nut, lock, 3/8-24
56 Screw, mattress strap
57 Bolt, toggle, 3/8-16 x 6"
58 Screw, flat-head, #7 x 1-1/4"
59 Screw, flat-head, #6 x 5/8"
60 Screw, cap, 1/2-13 x 3-1/2", fully-threaded
61 Screw, machine, round-head, #10 x 3/4"
62 Washer, lock, #10
63 Plate, center
64 Screw, cap, 1/2-13 x 2"
[#] Spring combinations vary with bed size. Contact SICO Customer
Service Department for specific information.
Order by Item Number. Specify “for Room Maker Wall Bed.”
Always provide the serial number of the bed when ordering parts.
SICO Incorporated reserves the right to substitute materials or make changes if materials are not available and such changes improve the product.

PARTS LIST
17
STANDARD BED
SIDE-FOLD BED
KING BED
Detail of
Padboard Hinge
On early models only.