Siegenia DRIVE User manual

H47.MOTS011EN-01 12.2017 1/2
1 Operaon with the infrared remote control
• During operaon, always point the remote control
towards the LED:
– With window drives, the LED is located at the top
edge of the frame.
– With li-slide drives, the LED is located at the
boom edge of the slide drive SA.
• Intense solar radiaon and light incidence can
reduce the range of the remote control.
• If, when a buon is pressed, no funcon is carried
out or the funcon indicator does not light up, the
baery must be replaced. Used baeries must be
disposed of in an environmentally safe manner.
Insert 2 new baeries of one of the following types:
Micro, LR03 or AAA
• To operate a drive, rst acvate the buon of the
programmed group (ALL or 1‒5).
Intermediate
posion2)
Open Close
all drives
Stop1) 10 min
venlaon3)
Drives 1‒5
1) The buon has no funcon with DRIVE axxent DK
2) The buon has no funcon with window drives.
3) Note for HS drive: Pressing the buon a second me cancels the mer. The
li-slide sash remains staonary. Pressing the buon once more restarts the
mer. The funcon controls the primary sash only.
2 Programming the infrared remote control
2.1 Window drives ‒ DRIVE axxent DK
1
1,2,3,5
1,2,3,4
Program
Delete
• Programming: Press buons 1, 2, 3 and 5 within a
period of 3 seconds
• Deleng: Press buons 1, 2, 3 and 4 within a period
of 3 seconds
– LED lights up green
2
1-5
• Select window 1 to 5:
– LED goes out aer 10 seconds.
– The remote control is programmed in or deleted
2.2 Window drives ‒MH10
1
• Press and hold buon for 5 seconds:
– 1 short acousc signal is emied
– 2 short acousc signals are emied
• Release the buon
– LED ashes red
2
1-5
• Select window 1 to 5:
– 1 short acousc signal - The remote control is
programmed in
– 1 long acousc signal - The remote control is
deleted
– LED goes out aer 10 seconds.
Operang instrucons
Infrared remote control DRIVE

12.20172/2 H47.MOTS011EN-01
1.1 Li-slide drives (HS drives)
1.1.1 Programming/deleng remote control
• Several li-slide drives can be programmed in to one
and the same group.
• Each li-slide sash must be programmed in
individually.
• Up to 8 remote controls can be programmed in on
one li-slide drive.
1
• Press "PROG" buon:
– LED ashes green
2
• Press and hold buon for 5 seconds:
– 1 short acousc signal is emied
– 2 short acousc signals are emied
• Release the buon
– LED ashes red
3
1-5
• Press buon for the required group briey once:
– 1 short acousc signal - The remote control for
the selected group is programmed in
– 1 long acousc signal - The remote control for
the selected group is deleted
1.1.2 Programming/deleng the special funcon
"close without locking"
The special funcon "close without locking" allows the
li-slide sash to be opened manually.
1. Scheme C: Close and lock the secondary sash
2. Move the li-slide sash1) to the end posion
(see operang instrucons for the li-slide drive).
3. Press the "PROG" buon1) (LED ashes green)
4. Press and hold buon for 4 seconds1) (1 brief signal,
then 2 brief signals audible)
5. Release the buon
6. Press and hold down remote control buon 1
7. 1 short acousc signal - Special funcon is
programmed in
1 long acousc signal - Special funcon is deleted
1) with scheme C = primary sash
Operaon of the special funcon
With Scheme C the buon on the primary sash
must be acvated. Only the primary sash opens or
closes.
• Close without locking:
Briey tap the buon on the li-slide sash once
• Close with locking:
Briey tap the buon on the li-slide sash twice
• Stopping the li-slide sash during closing:
Briey tap the buon on the li-slide sash twice
DRIVE
Operang instrucons
Infrared remote control