Siemens Gigaset 4210 User manual

DO NOT RETURN
THIS PRODUCT TO THE STORE!
Please read the following important information.
For Siemens Customer Care, product operation
information, or for problem resolution, call toll-free
1-888-777-0211
7 a.m. to 10 p.m. Central Standard Time EVERY DAY
www.icm.siemens.com
Visite nuestro sitio Web para obtener instrucciones en español.

Basic Steps for Getting Started
For optimal performance of your system, please follow all of these steps.
For fu detai s, see the User Manua .
Customer Care: 1-888-777-0211
Or visit our ebsite: www.icm.siemens.com
Visite nuestro sitio Web para obtener instrucciones en español. PB4210QSG
Gigaset 4210
Quick Start Guide

Customer Care: 1-888-777-0211 or visit our ebsite: www.icm.siemens.com
Visite nuestro sitio Web para obtener instrucciones en español.
IMPORTANT: For best reception, place the base in a high central
location, away from other electrical de ices. The installation of
the base unit should allow at least 8-inches between the base and
persons to be in compliance with FCC RF exposure guidelines.
STEP 1 Base Station Setup
At the Base Station:
1Insert small plug on cord into phone
jack. Place cord in base cable
channel. Insert power supply unit
into wall outlet.
2Insert plug on telephone cord into
telephone jack on base unit (clicks
into place). Place cord in cable
channel on bottom of base. Insert
other end of plug into telephone
jack on wall. Bottom view of base
Page/
Registration
button
STEP 2 Handset Setup / Registration
IMPORTANT: Charge batteries 12 to 14 hours before using the
handset for the first time.
+
+
–
–
At the Han set:
1Remove protective plastic film from display.
2Insert batteries as shown.
Telephone
jack an
cor
Power
supply unit
an cor
110 VAC
60 Hz
4Be sure power
supply is
plugged into
wall outlet.
3Place battery cover on back of handset
and push gently upward until it clicks into
place.
5or auto registration
to base, press and
hold the END key to
turn handset off and
place in base station
with display facing
out for 1 minute.

STEP 3 Area Codes
Customer Care: 1-888-777-0211 or visit our ebsite: www.icm.siemens.com
Visite nuestro sitio Web para obtener instrucciones en español.
If you subscribe to Caller ID from your local telphone company, complete
the steps below. If you do not subscribe to Caller ID, skip this section.
To call back from the Call Log, you must enter and store the Local Area
Code for the area where your phone is installed. If your phone is
installed in an area with multiple area codes, you will also have to enter
and store the Extra Codes for that area.
STORING LOCAL AREA CODE
1Open the Menu.
2Scroll to Base Settings and press OK.
3Scroll to Area Codes and press OK.
4Scroll to Local Area Code and press OK.
5Enter your area code and press OK.
STORING EXTRA AREA CODES
1Open the Menu.
2Scroll to Base Sett and press OK.
3Scroll to Area Codes and press OK.
4Scroll to  xtra Codes and press OK.
5To enter an extra area code, press Menu.
6Enter an extra area code and press OK.
Repeat steps 5 and 6 above to enter additional area codes.

Customer Care: 1-888-777-0211 or visit our ebsite: www.icm.siemens.com
Visite nuestro sitio Web para obtener instrucciones en español.
BASIC PHONE OPERATION
Making a Call 1Dial desired number.
2Press c or u speakerphone key.
3Press a or place handset in base (or charger) to
hang up.
See Gigaset 4210 or 4215 User Manual for voice dialing instructions.
Answering Call Press c or u speakerphone key.
Intercom Call 1Lift handset and select the handsets intercom number
F and press c.
2Or, press the handset number, such as F, .
3Or, select Intercom Call and press c.
4Or, select F, « to call all handsets.
Setting Volume 1Open the Menu G.
2Scroll to Sound Settings D and
press OK.
3Select Handset Volume and press OK.
You will hear the current volume of the speakerphone
and its level is displayed. Scroll to the desired volume
and press Save. You will hear and see in the display
the confirmation of the change.
4To set earpiece volume, scroll down D, select
desired earpiece volume G, and press Save.
Language Setting 1Open the Menu G .
2Scroll to H/Set Settings D and press
OK.
3Scroll to Language and press OK.
4Select the desired language and press OK.
A check mark appears next to the selected language.
Paging Handset Press the page button on the base bottom.

Ñ
MENURDL
Int 2
05.20.01 10:30
Û
HANDSET NAVIGATIONAL OPERATION
Signal strength:
Ðstrong
Ñme ium
Òweak
Date
Navigational (Navi) key
Talk k ey
In the Display:
Current functions
Press the navigational (Navi) key H
to navigate through the handset options.
Navi Control Telephone Idle Action Lists and Menus Entry Field
EHold down for Voice Dialing Upward Cursor up
DOpen Directory Downward Cursor down
GOpen Menu Select entry (OK) Cursor right
FList of internal intercom users One menu level back (cancel) Cursor left
Charging status:
Ý battery empty
battery low when flashing
Ú battery fully charge
Time
Soft keys:
Press the correspon ing si e
of the left or right soft key to
activate the function shown
in the isplay.
En call an On/Off key
Scroll to the left an right
when entering numbers or
messages.
Delete key (backspace):
Delete input from right to left.
Display and Soft Keys
Customer Care: 1-888-777-0211 or visit our ebsite: www.icm.siemens.com
Visite nuestro sitio Web para obtener instrucciones en español.
Navigation Display Symbols
<> X
××

The handset Directory will store up to 200 telephone numbers.
STORING DIRECTORY ENTRIES
1Open the Directory by pressing the Navi key on bottom D.
2Scroll to New ntry and press OK.
3Enter the telephone number and press OK.
4Scroll and enter the name and press OK.
5Press Menu G.
6Save entry by pressing OK.
DIALING FROM DIRECTORY
1Open the Directory by pressing the Navi key on bottom D.
2Enter the first letter of the name as entered
(for example, press ^ 2 x for E, Eric).
3Press the Talk cor Speakerphoneu key and the number is dialed.
The Memory dial list will store up to 9 telephone numbers. It is recommended that the 1
key be used for the answering machine or telephone company voice mail access.
STORING MEMORY ENTRIES
1Press the MemoryC key.
2Scroll to New ntry and press OK.
3Enter the telephone number and press OK.
4Using handset keypad, select a quick access key. Press the desired key
(2-9) and then enter the name (for example, to use quick access key 3
for Eric press ^ 4 x for 3, press ^ 2 x for E, press ¤ 3 x for
R, press ¡ 3 x for I, press  3 x for C).
5Press OK.
6Press Menu G.
7Save entry by pressing OK.
DIALING FROM MEMORY
1Press and hold the quick access key.
2Press the Talk cor Speakerphoneu key and the number is dialed.
Memory key
Customer Care: 1-888-777-0211 or visit our ebsite: www.icm.siemens.com
Visite nuestro sitio Web para obtener instrucciones en español.
DIRECTORY AND MEMORY DIALING

Siemens GigaVoice voice-operated controls for the 4200 series allow users to place calls
or hear whos calling. The system recognizes up to 20 names and numbers from the
directory and up to four users may record the same name or number. Subscription to Caller
ID from your local telephone company is required.
RECORDING A VOICE-DIAL ENTRY
1Open the Directory by pressing the Navi key on bottom.
2Press Speech.
3Select user 1-4 and press OK.
4Scroll to New ntry and press OK.
5Enter the telephone number.
6Scroll to the name field and enter the name.
7Press Record.
8Press Begin to start recording and speak the name of the desired
entry (for example Anne) to record a voice pattern.
9Repeat the name (for example Anne).
10 Press Save.
DIALING WITH YOUR VOICE
1Press the Navi key on top.
2At the prompt, speak the recorded voice pattern (for example Anne).
3When the voice pattern is recognized, the name is played back from
the handset and the number is dialed.
VOICE-ANNOUNCED CALLER ID
If the Caller ID telephone number transmitted for an incoming call corresponds to a
voice-dial entry, the voice pattern is played back on the loudspeakers of the handset
or base station.
1To turn on the Voice-Announced Caller ID feature, press Menu.
2Scroll to Base Settings and press OK.
3Scroll to Spec. Functions and press OK.
4Scroll to Caller ID and press OK (checkmark indicates feature is on).
Customer Care: 1-888-777-0211 or visit our ebsite: www.icm.siemens.com
Visite nuestro sitio Web para obtener instrucciones en español.
VOICE-OPERATED CONTROLS
D
E