Siemens SIMATIC ET 200SP HA Technical Document

SIMATIC
ET 200SP HA
DQ 16x24VDC/0.5A
Equipment Manual
6DL1132-6BH00-0PH1
6DL1132-6BH00-0EH1
10/2021
A5E39265993-AD
Security information 1
Preface 2
2D Matrix code (QR code /
EAN code) 3
Product overview 4
Terminal 5
Parameters 6
Displays and interrupts 7
Technical speci󹪝cations 8
Parameters, diagnostics
messages and address
space A

Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage
to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices
referring only to property damage have no safety alert symbol. These notices shown below are graded according to
the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will be
used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property
damage.
Quali󹪝ed Personnel
The product/system described in this documentation may be operated only by personnel quali󹪝ed for the speci󹪝c
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Quali󹪝ed personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended or
approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance
are required to ensure that the products operate safely and without any problems. The permissible ambient
conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identi󹪝ed by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication may
be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software described.
Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this
publication is reviewed regularly and any necessary corrections are included in subsequent editions.
Siemens AG
Digital Industries
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E39265993-AD
Ⓟ 11/2021 Subject to change
Copyright © Siemens AG 2021.
All rights reserved

Table of contents
1 Security information.............................................................................................................................. 5
2 Preface ................................................................................................................................................... 7
3 2D Matrix code (QR code / EAN code).................................................................................................... 9
4 Product overview................................................................................................................................. 11
4.1 I/O module......................................................................................................................... 11
4.2 Accessories........................................................................................................................ 12
4.3 Output disable switch ........................................................................................................ 13
4.4 Pulling the I/O module in runtime....................................................................................... 13
4.5 Terminal blocks.................................................................................................................. 14
5 Terminal ............................................................................................................................................... 15
5.1 Pin assignment .................................................................................................................. 15
5.2 Sample connection scheme for 1-wire connection.............................................................. 16
5.3 Sample connection scheme for 2-wire connection.............................................................. 17
5.4 Schematic circuit diagram .................................................................................................. 17
6 Parameters........................................................................................................................................... 19
6.1 Parameter types................................................................................................................. 19
6.2 Module/channel parameters............................................................................................... 19
6.3 Explanation of the module/channel parameters.................................................................. 20
6.3.1 Diagnostics, Missing supply voltage L+ ............................................................................... 20
6.3.2 IO redundancy ................................................................................................................... 20
6.3.3 Diagnostics short-circuit to L+ ............................................................................................ 21
6.3.4 Diagnostics, Short-circuit to ground.................................................................................... 21
6.3.5 Diagnostics, Wire break...................................................................................................... 21
6.3.6 Wire-break check ............................................................................................................... 21
6.3.7 Channel activated .............................................................................................................. 22
6.3.8 Reaction to CPU STOP......................................................................................................... 22
6.3.9 Substitute value................................................................................................................. 22
6.3.10 Potential group .................................................................................................................. 22
7 Displays and interrupts........................................................................................................................ 25
7.1 Status and error displays .................................................................................................... 25
7.2 LEDs .................................................................................................................................. 26
7.2.1 DIAG LED ........................................................................................................................... 26
7.2.2 MT LED.............................................................................................................................. 26
7.2.3 PWR LED ............................................................................................................................ 27
7.2.4 Channel status / fault LEDs ................................................................................................. 27
7.3 Interrupts .......................................................................................................................... 28
DQ 16x24VDC/0.5A
Equipment Manual, 10/2021, A5E39265993-AD 3

8 Technical speci󹪝cations ....................................................................................................................... 29
A Parameters, diagnostics messages and address space ....................................................................... 37
A.1 Parameter assignment ....................................................................................................... 37
A.2 Parameter assignment and structure of the module/channel parameters............................. 38
A.3 Diagnostics messages ........................................................................................................ 40
A.4 Maintenance events........................................................................................................... 42
A.5 Address space.................................................................................................................... 42
Tables
Table A-1 Address space of the DQ 16x24VDC/0.5A HA........................................................................... 43
Table of contents
DQ 16x24VDC/0.5A
4Equipment Manual, 10/2021, A5E39265993-AD

Security information 1
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is necessary
to implement – and continuously maintain – a holistic, state-of-the-art industrial security
concept. Siemens’ products and solutions constitute one element of such a concept.
Customers are responsible for preventing unauthorized access to their plants, systems,
machines and networks. Such systems, machines and components should only be connected to
an enterprise network or the internet if and to the extent such a connection is necessary and only
when appropriate security measures (e.g. 󹪝rewalls and/or network segmentation) are in place.
For additional information on industrial security measures that may be implemented, please
visit
https://www.siemens.com/industrialsecurity.
Siemens’ products and solutions undergo continuous development to make them more secure.
Siemens strongly recommends that product updates are applied as soon as they are available
and that the latest product versions are used. Use of product versions that are no longer
supported, and failure to apply the latest updates may increase customer’s exposure to cyber
threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS Feed
under
https://www.siemens.com/industrialsecurity.
DQ 16x24VDC/0.5A
Equipment Manual, 10/2021, A5E39265993-AD 5

Security information
DQ 16x24VDC/0.5A
6Equipment Manual, 10/2021, A5E39265993-AD

Preface 2
Validity of the documentation
This equipment manual describes the following I/O modules:
System family I/O module Article No.
SIMATIC Distributed I/O System ET 200SP
HA
DQ 16x24VDC/0.5A 6DL1132-6BH00-0PH1
SIMATIC Distributed I/O System ET 200SP
HA
DQ 16x24VDC/0.5A 6DL1132-6BH00-0EH1
It complements the system manual for the ET 200SP HA Distributed I/O System.
Functions that generally relate to the system are described in this manual.
The information in this device manual and the system/function manuals enables you to put the
ET 200SP HA into operation.
Conventions
Please also observe notes marked as follows:
Note
A note contains important information on the product described in the documentation, on the
handling of the product or on the section of the documentation to which particular attention
should be paid.
DQ 16x24VDC/0.5A
Equipment Manual, 10/2021, A5E39265993-AD 7

Preface
DQ 16x24VDC/0.5A
8Equipment Manual, 10/2021, A5E39265993-AD

2D Matrix code (QR code / EAN code) 3
The 2D matrix code on the product is a coded representation of the product-speci󹪝c article
number.
Access to product-related information
For reading the 2D matrix code, SIEMENS o󹪜ers an app for mobile use.
Information about the app and the download can be found on the Internet: "Mobile use via app
(https://support.industry.siemens.com/cs/ww/en/sc/2067)".
The app provides direct access to the technical forum and product-related posts, such as:
• FAQs
• Application examples
• Manuals
•Certi󹪝cates
• Product notices
DQ 16x24VDC/0.5A
Equipment Manual, 10/2021, A5E39265993-AD 9

2D Matrix code (QR code / EAN code)
DQ 16x24VDC/0.5A
10 Equipment Manual, 10/2021, A5E39265993-AD

Product overview 4
4.1 I/O module
De󹪝nition
The DQ 16x24VDC/0.5A I/O module is a digital output module with 16 power outputs for process
control.
In addition to the technical speci󹪝cations, this module has the following properties:
• Suitable for solenoid valves, DC contactors, and indicator lights
• Parameter reassignment in RUN
• Output disable switch
DQ 16x24VDC/0.5A
Equipment Manual, 10/2021, A5E39265993-AD 11

Description
The I/O module consists of the following components:
DIAG MT

DQ HA
16x24V DC /0,5A
7
DQ .6+
8
1
DQ .0+
2
3
DQ . 2+
4
5
DQ . 4+
6
1P1
L+
24VDC
M
1P2
2P1
L+
24VDC
M
2P2
MAX. 10 A
.0 .1
V 1.0.0
CC 02
PW R
6DL1132-6BH00-0PH1
X 2
34
DQ .7+
DQ .1+
DQ . 3+
DQ .5+
DQ a
15
DQ .6+
16
9
DQ .0+
10
11
DQ . 2+
12
13
DQ . 4+
14
DQ .7+
DQ.1+
DQ . 3+
DQ .5+
DQ b
2324
17 18
19 2 0
2122
M
31
25
27
29
32
26
28
30
F0 F1
.2 . 3
F2 F 3
.4 .5
F4 F 5
.6 .7
F6 F 7
.0 .1
F0 F 1
.2.3
F2F3
.4.5
F4F5
.6.7
F6 F 7
DQ b DQ a

①Module type and designation ⑧Output disable switch
②LED for diagnostics ⑨Module type color coding
③LED for maintenance ⑩Product version
④2D matrix code ⑪Function status and 󹪝rmware version
⑤Wiring diagram ⑫Color code for selection of the color-coded labels
⑥LEDs for channel status/channel
fault
⑬Serial number
⑦LED for supply voltage ⑭Article number
4.2 Accessories
De󹪝nition
Accessories for the I/O module must be ordered separately.
Description
The following accessories are available:
• Labeling strips
• Color-coded labels
Product overview
4.2 Accessories
DQ 16x24VDC/0.5A
12 Equipment Manual, 10/2021, A5E39265993-AD

• Reference identi󹪝cation label
• Shield connector
• Terminal blocks
4.3 Output disable switch
De󹪝nition
The output disable switch switches the I/O module load-free.
NOTICE
Dangerous plant conditions possible (disconnect the load)
If you want to pull the I/O module in runtime, you have to press the output disable switch for
3 seconds for the I/O module to be load free (deenergized).
Pulling the I/O module in runtime (Page 13)
4.4 Pulling the I/O module in runtime
Requirement
The normally closed contacts are closed.
Procedure
Press the output disable switch for 3 seconds.
Note
Pressing the output disable switch interrupts any ongoing 󹪝rmware update. A 󹪝rmware update
cannot be performed when the device is deenergized.
Result
The I/O module is load-free.
The LED DIAG 󹪞ashes red, the LED MT lights up yellow and the I/O module generates a
diagnostics message.
Status and error displays (Page 25)
Product overview
4.4 Pulling the I/O module in runtime
DQ 16x24VDC/0.5A
Equipment Manual, 10/2021, A5E39265993-AD 13

4.5 Terminal blocks
De󹪝nition
The terminal blocks provide the process terminals (push-in terminals) for components such as
devices to be connected.
Description
The following terminal blocks are available for the I/O module:
Article number Color Description
6DL1193-6TP00-0DH1 Lit
6DL1193-6TP00-0BH1 Dark
6DL1193-6TP00-0DM1 Lit For redundant con󹪝guration
6DL1193-6TP00-0BM1 Dark For redundant con󹪝guration
6DL1193-6TP00-0DN0 Lit With additional potential distributors for ground connection of the actuators
6DL1193-6TP00-0BN0 Dark With additional potential distributors for ground connection of the actuators
Note
Terminal blocks are not included in the scope of delivery of the I/O module and must be ordered
separately.
You can 󹪝nd additional information on the con󹪝guration in the system manual.
Product overview
4.5 Terminal blocks
DQ 16x24VDC/0.5A
14 Equipment Manual, 10/2021, A5E39265993-AD

Terminal 5
5.1 Pin assignment
De󹪝nition
The pin assignment provides information about the arrangement and marking of the
connections when wiring a connector.
Note
The M terminals are intended exclusively for the 1 or 2-wire connection system. You may not use
these terminals as the ground terminals for other devices in the system. Ensure that the total
current does not exceed 2A for each M terminal.
DQ 16x24VDC/0.5A
Equipment Manual, 10/2021, A5E39265993-AD 15

Description
The pin assignment is structured as follows:
Terminal Assignment Terminal Assignment Description
1DQ a/DQ.0+ 2DQ a/DQ.1+ DQ a /DQ.n+: Output signal, channel n (0…7)
DQ b /DQ.n+: Output signal, channel n (8…15)
M: Ground
1P1: Supply voltage L+ of the voltage bus 1P
2P1: Supply voltage L+ of the voltage bus 2P
1P2: Ground reference of the voltage bus 1P
2P2: Ground reference of the voltage bus 2P
7 DQ.6 + 8
1
DQ.0 +
2
3
DQ.2+
4
5
DQ.4+
6
1P1
L+ 24VDC M
1P2
2P1
L+ 24VDC M
2P2
MAX. 10 A
DQ.7+
DQ.1+
DQ.3+
DQ.5 +
DQ a
15
DQ.6 +
16
9
DQ.0 +
10
11
DQ.2+
12
13
DQ.4+
14
DQ.7+
DQ.1+
DQ.3+
DQ.5 +
DQ b
23 24
17 18
19 20
21 22
M
31
25
27
29
32
26
28
30
3DQ a/DQ.2+ 4DQ a/DQ.3+
5DQ a/DQ.4+ 6DQ a/DQ.5+
7DQ a/DQ.6+ 8DQ a/DQ.7+
9DQ b/DQ.0+ 10 DQ b/DQ.1+
11 DQ b/DQ.2+ 12 DQ b/DQ.3+
13 DQ b/DQ.4+ 14 DQ b/DQ.5+
15 DQ b/DQ.6+ 16 DQ b/DQ.7+
17 M18 M
19 M20 M
21 M22 M
23 M24 M
25 M26 M
27 M28 M
29 M30 M
31 M32 M
1P1 L+ 1P2 M
2P11L+ 2P2 M
1If the module is plugged into a TB45R-P32 terminal block suitable for IO redundancy, the potential at this terminal is 1P3.
5.2 Sample connection scheme for 1-wire connection
Example
'4Q0'4Q'4Q
Terminal
5.2 Sample connection scheme for 1-wire connection
DQ 16x24VDC/0.5A
16 Equipment Manual, 10/2021, A5E39265993-AD

5.3 Sample connection scheme for 2-wire connection
Example
'4Q0
5.4 Schematic circuit diagram
De󹪝nition
A block diagram contains the schematic representation of individual function blocks.
Description
The circuit diagram for the I/O module is structured as follows:
5HYHUVHSRODULW\SURWHFWLRQ(763+$%DFNSODQHEXVFRQQHFWLRQ,QIHHGRIPRGXOHVXSSO\ZLWKOLJKWWHUPLQDOEORFN
3RZHUEXVLQWKHWHUPLQDOEORFN%DFNSODQHEXVLQWKHDGDSWHUPRGXOH
0/0/33333
The supply voltage L+ must be applied to the I/O module at the start of a 󹪝rmware update and
during the 󹪝rmware update.
Terminal
5.4 Schematic circuit diagram
DQ 16x24VDC/0.5A
Equipment Manual, 10/2021, A5E39265993-AD 17

Terminal
5.4 Schematic circuit diagram
DQ 16x24VDC/0.5A
18 Equipment Manual, 10/2021, A5E39265993-AD

Parameters 6
6.1 Parameter types
De󹪝nition
You de󹪝ne and thereby in󹪞uence the functions supported by the module operation of the I/O
module via the parameter types.
6.2 Module/channel parameters
De󹪝nition
Module/channel parameters are speci󹪝c parameters whose con󹪝guration can a󹪜ect the entire
module or channels.
Note
Each con󹪝guration change resets the corresponding reaction.
Description
The following module/channel parameters are available:
Parameters Value range Default Parameter re‐
assignment in
RUN
E󹪟ciency range
Diagnostics, Missing supply
voltage L+ (Page 20)
• Enabled
• Disabled
Enabled Yes Module
IO redundancy (Page 20) • None
• 2 modules
None No Module
Diagnostics, Short-circuit to
ground (Page 21) 3
• Enabled
• Disabled
Enabled Yes Channel
Diagnostics short-circuit to L
+ (Page 21)
• Enabled
• Disabled
Enabled Yes Channel
Diagnostics, Wire break
(Page 21) 1
• Enabled
• Disabled
Enabled Yes Channel
Wire-break check (Page 21) • Enabled
• Disabled
Enabled Yes Channel
DQ 16x24VDC/0.5A
Equipment Manual, 10/2021, A5E39265993-AD 19

Parameters Value range Default Parameter re‐
assignment in
RUN
E󹪟ciency range
Channel activated
(Page 22)
• Enabled
• Disabled
Enabled Yes Channel
Reaction to CPU STOP
(Page 22)
• Shutdown
• Keep last value
• Output substitute value
Shutdown Yes Channel
Substitute value (Page 22)
2
• 0
• 1
0 Yes Channel
Potential group (Page 22) • Potential group of the left mod‐
ule (dark gray terminal block)
• New potential group (light gray
terminal block)
• No potential group (black termi‐
nal block)
Use potential
group of the left
module
No Module
1The wire break diagnostics can only be enabled when the "Check for wire break" parameter is enabled.
2Only in e󹪜ect when "Substitute value" has been enabled for the "Reaction to CPU STOP" parameter.
3In case of a short-circuit, only the speci󹪝c channel with short-circuit is switched o󹪜; all other channels of the digital output
module are still operable.
6.3 Explanation of the module/channel parameters
6.3.1 Diagnostics, Missing supply voltage L+
De󹪝nition
Enabling of the diagnostics for missing or insu󹪟cient supply voltage L+.
6.3.2 IO redundancy
De󹪝nition
You can con󹪝gure two identical modules redundantly. To do so, plug both modules into a
redundant terminal block side by side. You can 󹪝nd additional information on mounting
modules in an IO redundancy con󹪝guration in the ET 200SP HA System Manual, section
"Installing", "Installing terminal block".
In IO redundancy mode, the left module is the master and the right module is the slave. The
HART communication takes place exclusively via one of the two redundant channels.
Parameters
6.3 Explanation of the module/channel parameters
DQ 16x24VDC/0.5A
20 Equipment Manual, 10/2021, A5E39265993-AD