CREVIS FnIO S Series NA-9188 User manual

제품을 사용하시기 전에
저희 (주)크래비스 제품을 구입해 주셔서 감사합니다. 제품의 효율적인 사용을 위하여 반드시 본사용 설명서의 내용을 숙지 하신 후
사용해 주십시오.
안전상의 주의 사항 *경고와 주의로 구분되어 있으니, 필히 숙지 하여 주십시오.
1. NA-9188 제품 사양
FieldBus Input/Output System
■EtherNet/IP Network Adapter
■PROFIBUS Network Adapter
■Digital Input / Output
■Analog Input / Output
사용설명서
FnIO S-series
Class 2, adjacent to voltage rating (30Vmax.)
●전원이 인가된 상태에서 단자대를 만지지 마십시오.
●전원이 인가된 상태에서 제품을 조립하지 마십시오.
●제품내부에 금속성 이물질이 유입되지 않도록 하십시오.
●전원이 인가된 상태에서 배선 작업을 하지 마십시오.
●배선 작업은 전기공사 전문가가 해주십시오.
지시사항을 위반하였을 때, 심각한 상황을 초래하여 사망 또는 중상을 입을 가능성이 있는 경우
●제품의 정격전압 및단자배열을 확인 후배선하여 주십시오.
●주변 온도가 55℃를넘는 장소는 피해 주십시오.
●직사 광선이 직접 노출된 장소는 피해 주십시오.
●주변 습도가 85%를넘는 장소는 피해 주십시오.
●가연성 물질이 있는 주변에 설치하지 마십시오.
●제품에 직접 진동이 인가되지 않도록 하십시오.
●전문 A/S요원 외에는 제품을 분해,수리,개조하지 마십시오.
●사용설명서에 명기된 환경조건에서 사용해 주십시오.
●확장 연결되는 모듈의 부하는 규정된 정격 이내로 사용해 주십시오.
지시사항을 위반하였을 때, 경미한 상해나 제품손상 및대물손해가 발생할 가능성이 있는 경우
NA-9188
구분 일반사양 구분 상세사양
사용/보존 온도 -20℃~55℃ / -40℃~85℃ Network 방식 EtherNet/IP, BOOTP
사용/보존습도 5% ~ 90% 단, 이슬이 맺히지 않을 것Cable EtherNet Cable
내진동/내충격 IEC68-2-6(2G) / 10G Cable 길이(m) Up to 100m from Ethernet Hub
EMC/ESD EN50082 / EN50081 통신속도(Kbps) 10/100Mbps
확장 모듈 위치 FnIO-S series의가장 왼쪽에 장착 확장모듈수 Max. 32 module
사용환경 부식성 가스가 없고, 먼지가 심하지
않을 것Max. Nodes Limited by Ethernet Specification
필드 공급전압 Class 2, 24VDC
24VDC (11VDC ~ 28.8VDC)Operating Mode Ethernet/IP, BOOTP
필드 공급전류 최대 10A 최대 Digital I/O Input : 2016점/ Output : 2016점
FnBus공급전류 최대 1.5A@5Vdc 최대 Analog I/O Input : 126Ch / Output : 126Ch
Isolation
System power to internal logic : Non-
isolation System power to I/O driver :
Isolation
최대 Byte수Input : 252Bytes / Output : 252Bytes
외형치수 45mm ×99mm ×70mm IP address
Setting BOOTP
무게 150g 내부 소비전류 60mA typical @24Vdc
인증 UL / cUL / CE / FCC / RoHS(EU, China)
감전사고 및오동작의 원인이 됩니다.
화재, 감전사고 및오동작의 원인이 됩니다.
화재, 감전사고 및오동작의 원인이 됩니다.
감전사고 및오동작의 원인이 됩니다.
화재, 감전사고 및오동작의 원인이 됩니다
화재,감전사고, 오동작의 원인이 됩니다.
화재,감전사고, 오동작의 원인이 됩니다.
화재,감전사고, 오동작의 원인이 됩니다.
화재,감전사고, 오동작의 원인이 됩니다.
화재의 원인이 됩니다.
화재 및감전의 원인이 됩니다.
화재 및감전사고의 원인이 됩니다.
감전, 화재, 오동작 또는 제품 열화의 원인이 됩니다.
화재, 오동작 또는 고장의 원인이 됩니다.
Update : 2013.1.30 * Power Isolators must be used according to the usage of 5VDC/24VDC/48VDC or AC Voltage modules
CVS-18-04A-010 Rev 2.02

2. 통신선 배선 및전원선 배선 방법
2.5 ㎟
이하
System 전원 및Field 전원 배선 시주의 사항
1. 통신 모듈에 통신전원과 Field용전원으로 구분하여 사용합니다.
1) 통신 전원 : Serial 통신을 위한 전원, System 전원
2) Field 전원 : I/O 연결 시사용하기 위한 전원
2. 통신용 Power Supply 와Field용Power Supply를반드시 구분하여 사용하여 주십시오.
3. 선은 케이블끼리 단락 되지 않도록 비닐 Tape등으로 처리하여 주십시오.
4. 통신로에 Serial통신 제품이외의 기기(예:변전기)를삽입하지 말아 주십시오.
- 신호의 반사 등의 영향에 의해, 정상적으로 통신이 되지 않는 경우가 있습니다.
5. System 전원의 소비전류에 의해 I/O의확장이 제한이 될수있습니다.
3. 모듈 설치 방법
3-1. Din-Rail에모듈 장착 방법
3-2. Din-Rail에서 모듈 탈착 방법
①Din rail 고정용 고리를 –자드라이버를
이용하여 아래로 내려주십시오.
①Din-Rail 위에서 아래 방향
으로 살짝 눌러 주십시오.
②딸칵 소리가 날때까지 눌러
주시면 장착이 완료됩니다.
②모듈의 양쪽 끝을 잡고 위방향
으로 들어 주시면 탈착됩니다.
2-1. EtherNet Communication
Line wiring

4. 모듈의 부분별 명칭과 기능
3 4
5
상태 표시 LED 창
(내용설명 참조)
EtherNet 연결 커넥터 시리얼 통신용 커넥터 (제조회사 Update용)
Din rail 고정용 손잡이
*1
상태 표시 LED 창설명
2 케이블 커넥터용(장/탈착식 Terminal Block)
6 MAC ID
Item LED is: State To indicate:
MOD :
Module
Status LED
Off No Power No power is supplied to the unit.
Green Device Operational The unit is operating in normal condition.
Flashing Green Device in Standby The device needs commissioning due to configuration
missing, incomplete or incorrect.
Flashing Red Minor Fault Recoverable Fault
- EEPROM sum check error.
Red Unrecoverable Fault The device has an unrecoverable fault.
- Memory error or CPU watchdog error.
NET :
Network
Status LED
Off Not Powered
No IP Address
Module is not powered.
Does not have an IP address
Flashing Green No Connections Module has obtained an IP address, but has no
Established connections.
Green CIP Connections Module has an IP address and at least one established
connections.
Flashing Red Connection Time-out One or more of the connections in which the module is
The target has time out.
Red Duplicate IP Address
Module has detected that its IP address is already in
use.
Configure the module with a unique IP address.
LINK :
Link/Active
Status LED
Off
Not Powered
Physical network not
ready
May not be powered
Green Link Operational Physical Network communication ready
Flashing Green Act Operational some data communication on the base Ethernet 802.3
I/O :
Expansion
Module
Status LED
Off Not Powered
No Expansion Module
Device has no expansion module or may not be
powered
Flashing Green FnBus On-line,
Do not Exchanging I/O
FnBus is normal but does not exchanging I/O data
(Passed the expansion module configuration).
Green FnBus Connection,
Run Exchanging IO Exchanging I/O data
Flashing Red FnBus connection fault
during exchanging IO
One or more expansion module occurred in fault state.
- Changed expansion module configuration.
- FnBus communication failure.
Red
Expansion
Configuration
Failed
Failed to initialize expansion module
- Detected invalid expansion module ID.
- Overflowed Input/Output Size
- Too many expansion module
- Initial protocol failure
- Mismatch vendor code between adapter and
expansion module.
Field
Power
Status LED
Off Not Supplied Field
Power Not supplied 24Vdc field power
Green Supplied Field Power Supplied 24Vdc field power

사양 및디자인은 사전 예고없이 변경될 수있습니다.
5. I/O Image Mapping 방법
6. 설치 방법
HubFnIO FnIO
100m 이내 100m 이내
* 확장 모듈은 I/O Data, Configuration Data, 그리고 Memory Resister등3가지 형식의 Data를처리합니다.
Network Adapter는입.출력 Data에대해 별개의 메모리 영역을 가지고 있습니다.
※ 주의
- EIP의속도등을 보증하기 위해서는 전용 HUB를사용을 권장합니다.
- 통신케이블은 노이즈에 대책이 된케이블 사용을 권장합니다.
㈜크래비스
경기도 용인시 기흥구 기곡로 29-4
대표전화 031-899-4599 FAX [phone]
홈페이지 www.crevis.co.kr

FieldBus Input/Output System
■EtherNet/IP Network Adapter
■PROFIBUS Network Adapter
■Digital Input / Output
■Analog Input / Output
■Special Module
Quick Guide
FnIO S-series
NA-9188
1. NA-9188 Specification
* Specifications and designs could be changed without advance Notice.
Class 2, adjacent to voltage rating (30Vmax.)
ITEM SPECIFICATION ITEM SPECIFICATION
Ambient Temp. -20℃~55℃ / -40℃~85℃ Network Type EtherNet/IP, BOOTP
Relative Humidity 5% ~ 90% without condensation Cable EtherNet Cable
Durable-vib./impact IEC68-2-6(2G) / 10G Cable Length(m) Up to 100m from Ethernet Hub
EMC/ESD EN50082 / EN50081 Comm. Sp(Kbps) 10/100Mbps
Mount Position On the left of FnIO-S series Expansion No. Max. 32 module
Atmosphere Not so dusty without corrosive gas Max. node Limited by Ethernet Specification
Field Supp.Volt. Class 2, 24VDC
24VDC (11VDC ~ 28.8VDC)Max. Digital I/O Input : 2016points/Output :
2016points
Field Supp. Cur. Max. 10A Max. Analog I/O Input : 126Ch / Output : 126Ch
FnBus Sup. Cur Max. 1.5A@5Vdc Max. Byte size Input : 252Bytes / Output : 252Bytes
Isolation
System power to internal logic :
Non-isolation
System power to I/O driver :
Isolation
Operating Mode Ethernet/IP, BOOTP
Size 45mm ×99mm ×70mm IP Address Setting BOOTP
Weight 150g Power Dissipation 60mA typical @24Vdc
Certification UL / cUL / CE / FCC / RoHS(EU,
China)
Cautions for your Safety
Do not assemble the products and wire with power applied to the system. Else it may cause an electric arc, which can result into unexpected
and potentially dangerous action by field devices. Arching is explosion risk in hazardous locations. Be sure that the area is non-hazardous or
remove system power appropriately before assembling or wiring the modules.
Do not touch any terminal blocks or IO modules when system is running. Else it may cause the unit to an electric shock or malfunction.
Keep away from the strange metallic materials not related to the unit and wiring works should be controlled by the electric expert engineer.
Else it may cause the unit to a fire, electric shock or malfunction.
If you don’t follow the directions, it could cause a personal injury, damage to the equipment or explosion
If you disobey the instructions, there may be possibility of personal injury, damage to equipment or
explosion. Please follow below Instructions.
Check the rated voltage and terminal array before wiring. Avoid the circumstances over 55℃of temperature. Avoid placing it directly in the
sunlight.
Avoid the place under circumstances over 85% of humidity.
Do not place Modules near by the inflammable material. Else it may cause a fire.
Do not permit any vibration approaching it directly.
Go through module specification carefully, ensure inputs, output connections are made with the specifications. Use standard cables for wiring.
Use Product under pollution degree 2 environment.
Before using the unit
*We appreciate you for purchasing CREVIS Products. To use the units more effectively, please read this quick guide and refer to
the respective user manual for further details.
Warning!
Caution!
* Power Isolators must be used according to the usage of 5VDC/24VDC/48VDC or AC Voltage modules

2. Communication & Power Line Wiring
2-1. EtherNet Communication Line wiring
< 2.5 ㎟
3. Module Mounting
3-1. How to mount on Din-Rail
3-2 How to dismount from Din-Rail
①Pull down the locking mechanism by using
(- ) screw driver as the following pictures ;
①Press down the module lightly
on the Din-Rail until it clicks . ②Press down till you can hear “click”forcomplicatedmount.
②Pull up the module to remove
from the din rail .
Notice for Wiring of communication and Field power
1. The communication power and Field power respectively are supplied to each network adapter.
1) Communication Power : Power for Serial communication and System power.
2) Field Power : Power for I/O Connection
2. The Power Supply have to be used for Communication and Field separately .
3. To avoid a short circuit, tape the un-shield wire.
4. Do not insert any other devices such as converter into the connecter besides Serial communication products.

4. Name of each Part
3 4
5
Status LED Window(refer to the
description below)
EtherNet Connector Serial Communication Connector
( For manufacturer use only)
Latch for DIN Rail
*1
Description for LED status
2 Removable Terminal Block
6 MAC ID
Item LED is: State To indicate:
MOD :
Module
Status LED
Off No Power No power is supplied to the unit.
Green Device Operational The unit is operating in normal condition.
Flashing
Green Device in Standby The device needs commissioning due to configuration missing, incomplete or incorrect.
Flashing Red Minor Fault Recoverable Fault
- EEPROM sum check error.
Red Unrecoverable Fault The device has an unrecoverable fault.
- Memory error or CPU watchdog error.
NET :
Network
Status LED
Off Not Powered
No IP Address
Module is not powered.
Does not have an IP address
Flashing
Green No Connections Module has obtained an IP address, but has no Established connections.
Green CIP Connections Module has an IP address and at least one established
connections.
Flashing
Red Connection Time-out One or more of the connections in which the module is The target has time out.
Red Duplicate IP Address Module has detected that its IP address is already in use.
Configure the module with a unique IP address.
LINK :
Link/Active
Status LED
Off
Not Powered
Physical network not
ready
May not be powered
Green Link Operational Physical Network communication ready
Flashing
Green Act Operational some data communication on the base Ethernet 802.3
I/O :
IO Module
Status LED
Off Not Powered
No IO Module Device has no IO module or may not be powered
Flashing
Green
FnBus On-line,
Do not Exchanging I/O
FnBus is normal but does not exchanging I/O data
(Passed the IO module configuration).
Green FnBus Connection,
Run Exchanging IO Exchanging I/O data
Flashing
Red
FnBus connection fault
during exchanging IO
One or more IO module occurred in fault state.
- Changed IO module configuration.
- FnBus communication failure.
Red
Expansion
Configuration
Failed
Failed to initialize IO module
- Detected invalid IO module ID.
- Overflowed Input / Output Size
- Too many IO module
- Initial protocol failure
Field Power
Status LED
Off Not Supplied Field
Power Not supplied 24Vdc field power
Green Supplied Field Power Supplied 24Vdc field power

5. I/O Image Mapping
6. Setting
Hub
FnIO FnIO
Upto 100m Upto 100m
*The Expansion module control 3 types of data such as I/O Data, Configuration Data and Memory Resister.
Network Adapter has memory field for In/Output data respectively.
* Specifications and designs may be changed without advance Notice.
※Caution
- Industrial HUB for EIP recommended
- Cable, the noise cable recommended
CREVIS Co., Ltd
29-4, Gigok-ro, Giheung-gu, Yongin-si,
Gyeonggi-do, Korea 446-930
TEL : [phone] FAX : [phone]
Homepage : www.crevis.co.kr