Siemens 6DL2804 Series Assembly instructions

Distributed I/O device 6DL2804-xxxxx
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
SIMATIC
Distributed I/O
Distributed I/O device 6DL2804-xxxxx
Hardware Installation Manual
03/2014
A5E34318119
Introduction
1
Safety information
2
Description
3
Mounting
4
Maintenance and servicing
5
Technical specifications
6
Ground points in the
enclosure
7
Dimension drawings
8
ESD Guidelines
9
Service and support
10
Siemens Controls

Siemens AG
Industry Sector
Postfach 48 48
90026 NÜRNBERG
GERMANY
Order number: A5E00378896F
Ⓟ06/2014 Subject to change
Copyright © Siemens AG 2008 - 2014.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury
will
result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury
may
result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by
personnel qualified
for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

Distributed I/O device 6DL2804-xxxxx
Hardware Installation Manual, 03/2014, A5E00378896F-03 3
Table of contents
1 Introduction............................................................................................................................................. 5
1.1 Purpose of this documentation ......................................................................................................5
1.2 History ............................................................................................................................................5
2 Safety information ................................................................................................................................... 7
2.1 General information .......................................................................................................................7
2.2 Laws and directives .......................................................................................................................7
2.3 Qualified personnel ........................................................................................................................7
2.4 Measures .......................................................................................................................................8
3 Description.............................................................................................................................................. 9
3.1 Overview ........................................................................................................................................9
3.2 Area of application .........................................................................................................................9
3.3 Product features...........................................................................................................................10
3.4 Structure of the type designation .................................................................................................11
3.5 Design of enclosure .....................................................................................................................12
3.6 Details of the enclosure ...............................................................................................................15
4 Mounting............................................................................................................................................... 19
4.1 Transport and storage..................................................................................................................20
4.2 Mounting the enclosure................................................................................................................20
4.3 Installing the enclosure outdoors .................................................................................................22
4.4 Optional installation components .................................................................................................23
4.5 Use of I/O device at temperatures down to -40 °C ......................................................................24
5 Maintenance and servicing.................................................................................................................... 27
6 Technical specifications ........................................................................................................................ 29
7 Ground points in the enclosure.............................................................................................................. 33
8 Dimension drawings.............................................................................................................................. 35
8.1 Installation: ET200iSP components.............................................................................................35
8.2 Installation: Heating .....................................................................................................................37
8.3 Installation: FO conductor ............................................................................................................38
9 ESD Guidelines .................................................................................................................................... 39
10 Service and support .............................................................................................................................. 41
Index..................................................................................................................................................... 43
Siemens Controls

Table of contents
Distributed I/O device 6DL2804-xxxxx
4Hardware Installation Manual, 03/2014, A5E00378896F-03
Tables
Table 6- 1 Technical specifications 6DL2804-xxDxx / xxExx / xxFxx / xxGxx ..............................................29
Table 6- 2 Technical specifications 6DL2804-xMDxx / xMExx .....................................................................30
Table 6- 3 Technical specifications 6DL2804-xxKxx / xxTxx / xxUxx ...........................................................31
Figures
Figure 3-1 Standard enclosure 6DL2804-0xD...Gxx .....................................................................................12
Figure 3-2 Standard enclosure 6DL2804-0xH...Wxx, view 1 ........................................................................13
Figure 3-3 Standard enclosure 6DL2804-0xH…Wxx, view 2........................................................................14
Figure 4-1 Drilling template for securing the device ......................................................................................20
Figure 4-2 Temperature response with 100 W heater for 6DL2804-xxDxx / -xxExx.....................................24
Figure 4-3 Temperature response with 200 W heater for 6DL2804-xxKxx / -xxUxx.....................................25
Figure 7-1 Fixed and detachable connections to ground and equipotential bonding rail..............................33
Figure 8-1 Distributed I/O device 6DL2804-xxD...Gxx with installation of ET 200iSP ..................................35
Figure 8-2 Distributed I/O device 6DL2804-xxH...Wxx with installation of ET200iSP...................................36
Figure 8-3 Distributed I/O device with installation of heating ........................................................................37
Figure 8-4 Distributed I/O device with installation of FO coupler: single and redundant designs.................38
Figure 9-1 Electrostatic voltages on an operator...........................................................................................40

Distributed I/O device 6DL2804-xxxxx
Hardware Installation Manual, 03/2014, A5E00378896F-03 5
Introduction
1
1.1
Purpose of this documentation
This manual contains all the information that you will require to install and use the device.
It is intended for persons who install the device mechanically, connect it electrically, set
parameters and commission it, as well as for service and maintenance technicians.
1.2
History
The most important changes in the documentation compared with the previous edition are
shown in the following table.
Edition
Comment
01/2008 First edition
08/2009 •Troubleshooting
•New functions (see technical specifications)
•Update owing to new standards
03/2014 Content changes: Safety instructions, enclosure
Siemens Controls

Introduction
1.2 History
Distributed I/O device 6DL2804-xxxxx
6Hardware Installation Manual, 03/2014, A5E00378896F-03

Distributed I/O device 6DL2804-xxxxx
Hardware Installation Manual, 03/2014, A5E00378896F-03 7
Safety information
2
2.1
General information
This device left the factory in a perfect state with regard to safety. To maintain this status and
to ensure safe operation of the device, note and follow the instructions and warnings in this
manual.
2.2
Laws and directives
Observe the provisions of the test certification valid for your country.
Electrical connection in potentially explosive atmospheres
When making electrical connections, observe the national regulations and laws for
hazardous areas valid for your country. In Germany, for example, the following apply:
●Ordinance on Industrial Safety and Health
●Standard relating to the installation of electrical systems in hazardous areas DIN EN
60079-14 (previously VDE 0165, T1)
2.3
Qualified personnel
Qualified personnel are people who are familiar with the installation, mounting,
commissioning, and operation of the product. These people have the following qualifications:
●They are authorized, trained or instructed in operating and maintaining devices and
systems according to the safety regulations for electrical circuits, high pressures and
aggressive as well as dangerous media.
●For devices intended for use in explosive atmospheres: They are authorized, trained, or
instructed in working on electrical circuits for systems in potentially explosive
atmospheres.
●They are trained or instructed in maintenance and use of appropriate safety equipment
according to the safety regulations.
●They should be trained in first aid.
Siemens Controls

Safety information
2.4 Measures
Distributed I/O device 6DL2804-xxxxx
8Hardware Installation Manual, 03/2014, A5E00378896F-03
2.4
Measures
In the interest of safety, observe the following precautionary measures:
WARNING
Type of protection "Flameproof enclosure d"
Devices with "pressure-resistant encapsulation" protection may only be opened when the
power has been disconnected.
Type of protection "Intrinsic safety i"
"Intrinsically-safe" devices lose their certification as soon as they are operated on circuits
which do not correspond with the test certification valid in your country.
Type of protection "Increased safety e"
Devices with the type of protection "Increased safety" must not produce sparks or electric
arcs during operation under normal conditions. Electrical equipment and parts must not
exceed a rated voltage of 11 kV.
Type of protection "Mold encapsulation m"
Devices with the type of protection "Mold encapsulation" are potted in casting compound.
Type of protection "By means of enclosure t"
Devices with the type of protection "By means of enclosure" prevent the penetration of dust
or reduce it to a harmless level. Explosive equipment can be installed. The temperature on
the housing must not ignite the surrounding atmosphere.
WARNING
Use in environments with aggressive and dangerous media
The device can be operated both at high pressure and with aggressive and hazardous
media. Therefore, improper use of this device may lead to serious injury and or
considerable damage to property. Above all, it must be noted when the device was in use
and is to be exchanged.
CAUTION
Electrostatic sensitive devices
This device contains electrostatic sensitive devices. ESD devices can be destroyed by
voltages well below the threshold of human perception. These static voltages develop when
you touch a component or electrical connection of a device without having discharged the
static charges present on your body. The damage to a module as a result of overvoltage
cannot usually be detected immediately. It may only become apparent after a long period of
operation.

Distributed I/O device 6DL2804-xxxxx
Hardware Installation Manual, 03/2014, A5E00378896F-03 9
Description
3
3.1
Overview
The device is used as a control, switching and distribution unit in hazardous areas (gas:
Zones 1, 2; dust: 21, 22; mining: M2). The product satisfies the requirements of the following
standards
●EN/IEC 60079-0 General requirements
●EN/IEC 60079-7 Enhanced safety
●EN/ICE 60079-31 Protection by means of enclosure
The device consists of the wall-mounted enclosure and the components installed in it, for
each of which there are separate certificates.
The device is also identified by the standards of the installed components. The supplied
ATEX certificate applies to the device and to the components installed by the manufacturer.
3.2
Area of application
●The wall-mounted enclosure is suitable for installation and operation of distributed I/Os,
e.g. ET 200iSP or ET 200, in the following hazardous areas:
–Device group I (mining, M2)
–Device group II (Zones 1 + 2 gas, and Zones 21 + 22 dust)
●The device consists of the wall-mounted enclosure (6DL2804-0xxxx) and the installed
electronic components.
●The device has been tested and certified for use in these hazardous areas.
Note
Product information on the Internet
You will find further information on installing and connecting the electronic components,
for example in:
•ET 200iSP manual (A5E00247482)
•Principles of explosion protection manual (6ES7398-8RA00-8BA0)
This information is available on the Internet on the Siemens home page.
●Only open the enclosure in Zones 21 and 22 if no ignitable dust atmosphere is present.
●The device is identified depending on:
–The installed components
–Use for the following hazardous areas: gas, dust or mining
Siemens Controls

Description
3.3 Product features
Distributed I/O device 6DL2804-xxxxx
10 Hardware Installation Manual, 03/2014, A5E00378896F-03
3.3
Product features
The device consists of a separately certified wall-mounted enclosure (6DL2804-0xxxx). The
enclosure is made of stainless steel and is intended for wall mounting.
The device is intended for the installation of control and measuring devices such as:
●Distributed I/O systems:
–ET 200iSP for use in Zones 1 and 2 (gas), Zones 21 and 22 (dust), and M2 (mining)
●Modular electro-pneumatic automation system AirLine Ex (type 8650, from the company
Bürkert)
●Buffer stages and safety barriers
●Relays, buffer elements and fuses
●Separate terminals for intrinsically safe and non-intrinsically safe circuits
●Command and signaling devices
●Temperature sensors
●Heating and thermostat
●Lightning protection components
●FO coupler