Siemens SICAM A8000 Series User manual

DC8-012-2.06 Unrestricted
SICAM A8000 Series
SICAM I/O Modules
Manual
Preface
Table of Contents
Open Source Software
Introduction
1
Standard I/O Modules
2

Siemens AG Unrestricted Order no.: DC8-012-2.06
Energy Automation
Humboldtstraße 59
90459 Nürnberg
Germany
Note
Please observe Notes and Warnings for your own safety in the Preface.
Disclaimer of Liability
Although we have carefully checked the contents of this publication
for conformity with the hardware and software described, we cannot
guarantee complete conformity s
ince errors cannot be excluded.
The information provided in
this manual is checked at regular
intervals and any corrections that might become necessary are
included in the next releases. Any suggestions for improvement are
welcome.
Subject to change without prior notice.
Document Label:
SICRTUs-HBSICAMIOMODULE-ENG_V2.06
Issuing date:
2019-09-13
Copyright
Copyright © Siemens AG
2019
The reproduction, transmission or use of this document or its
contents is not permitt
ed without express written authority.
Offenders will be liable for damages. All rights, including rights
created by patent grant or registration of a utility model or design,
are reserved.

SICAM A8000 Series, SICAM I/O Modules Unrestricted 3
DC8-012-2.06, Edition 09.2019
Preface
This document is applicable to the following product(s):
•CP-8000
•CP-8021
•CP-8022
Purpose of this manual
This manual describes the characteristics and functions of all SICAM input/output modules.
It contains:
•Functional Overviews
•Technical Data
•Interface Descriptions
•External Circuit Elements
Target Group
The document you are reading right now is addressed to sales engineers and users who are
in charge of the following engineering tasks:
•Evaluation of the module specifications
•Evaluation of quotation criteria, such as technical specifications
•Conceptual activities, as for example design and configuration
•Electrical installation
•Technical system maintenance and service, module handling
Recommendations for Third-Party Products
Siemens does neither receive liability nor warranty for recommendations which are given or
implied by this manual. For the correct and intended use of the respective product the
associated technical descriptions must be paid attention to in any case.
References to Third-Party Web Sites
Siemens is not responsible for the contents of third-party websites mentioned in this
document, as well as the correctness of the publications and links. For all product information
the respective manufacturer is responsible.

Preface
4Unrestricted SICAM A8000 Series, SICAM I/O Modules
DC8-012-2.06, Edition 09.2019
Placement in the Information Landscape
Document Item number
Common Functions Peripheral Elementes according to IEC 60870-5-101/104 DC0-011-2
SICAM A8000 Series – CP-8000, CP-8021, CP-8022 Manual DC8-023-2
You find current product information on our website: www.siemens.com/sicam.
Further Support
For more information, please contact our Customer Support Center:
Phone: [phone]
Fax: [phone]
(charges depending on provider)
e-mail: [e-mail]
The Siemens Power Academy offers a comprehensive program of professional training events
in the fields of power generation, distribution and transmission.
Main training centers are:
Nuremberg, Germany (Head Office)
Phone: [phone]
Fax: [phone]
[e-mail]
Vienna, Austria
Phone: [phone]
Fax: [phone]
[e-mail]
Schenectady, NY, USA
Phone: [phone]
Fax: [phone]
[e-mail]
Hebburn, United Kingdom
Phone: [phone]
Fax: [phone]
[e-mail]

Preface
SICAM A8000 Series, SICAM I/O Modules Unrestricted 5
DC8-012-2.06, Edition 09.2019
Notes on Safety
This manual does not constitute a complete catalog of all safety measures required for
operating the equipment (module, device) in question because special operating conditions
might require additional measures. However, it does contain notes that must be adhered to for
your own personal safety and to avoid damage to property. These notes are highlighted with a
warning triangle and different keywords indicating different degrees of danger.
Danger
means that death, serious bodily injury or considerable property damage
will occur, if the appropriate
precautionary measures are not carried out.
Warning
means that death, serious bodily injury or considerable property damage
can occur, if the appropriate
precautionary measures are not carried out.
Caution
means that minor bodily injury or property damage could occur, if the appropriate precautionary measures
are not carried out.
Note
is important information about the product, the
handling of the product or the respective part of the
documentation, to which special attention is to be given.

Preface
6Unrestricted SICAM A8000 Series, SICAM I/O Modules
DC8-012-2.06, Edition 09.2019
Qualified Electrical Engineering Personnel
Qualified electrical engineering personnel may commission and operate the device described
in this document. Qualified electrical engineering personnel in the sense of this document are
people who can demonstrate up to date technical qualifications as electrical technicians
including safety and first aid training. These person may commission, isolate, ground and
label devices, systems and circuits according to the standards of safety engineering.
Use as Prescribed
The device may only be used for such applications as set out in the catalogs and the technical
description, and only in combination with third-party equipment recommended and approved
by Siemens.
Correct and safe operation of the product requires adequate transportation, storage,
installation and mounting in a control cabinet, as well as appropriate use and maintenance.
During operation of electrical equipment, it is unavoidable that certain parts of this equipment
will carry dangerous voltages. Severe injury or damage to property can occur if the
appropriate measures are not taken:
•Before making any connections, ground the equipment at the grounding terminal.
•Hazardous voltages can be present on all switching components connected to the power
supply.
•The device does not represent a safety-oriented application; it does not provide fault
protection. Any fault protection must be provided by protection relays or other suitable
means.
•Even after the supply voltage has been disconnected, hazardous voltages can still be
present in the equipment (capacitor storage).
•LED display does not ensure that the connectors are free of voltage.
•Equipment with current transformer circuits must not be operated while open.
•The limit values indicated in the manual must not be exceeded; that also applies to testing
and commissioning.
Danger
Consider obligatory the safety rules for the accomplishment of works at electrical plants:
1. Switch off electricity all
-pole and on all sides!
2. Ensure that electricity cannot be switched on again!
3. Double check that no
electrical current is flowing!
4. Discharge, ground, short circuit!
5. Cover or otherwise isolate components
that are still electrically active!

Preface
SICAM A8000 Series, SICAM I/O Modules Unrestricted 7
DC8-012-2.06, Edition 09.2019
Statement of Conformity
The product described conforms to the regulations of the following European Directives:
•
2014/30/EU
Directive of the European Parliament and of the Council of 26 February 2014 on the harmonization
of the laws of the Member States relating to electromagnetic compatibility; Official Journal of the EU
L96, 29/03/2014, p. 79–106
•
2014/35/EU
Directive of the European Parliament and of the Council of 26 February 2014 on the harmonization
of the laws of the Member States relating to the making available on the market of electrical
equipment designed for use within certain voltage
limits; Official Journal of the EU L96, 29/03/2014,
p. 357–374
•
2011/65/EU
Directive of the European Parliament and of the Council of 8 June 2011 on the restriction of the use
of certain hazardous substances in electrical and electronic equipment; Official Journal of the EU
L174, 01/07/2011, p. 88-110
The conformity of the product with the above mentioned regulations is proven through the observance
of the following harmonized standards:
•
EN 60870-2-1:1996 for 2014/30/EU
•
EN 61010-1:2010 and EN 61010-2-201:2013 for 2014/35/EU; EN 61010-2-030:2010 (only AI-8510,
AI-8511, CM-8820)
•
EN 50581:2012 for 2011/65/EU
This declaration certifies the conformity with the specified directives, but is not an assurance of
characteristics in the sense of the product liability law.
The product is intended exclusively for use in an industrial environment.
Other Standards
UL 61010
-2-201 including UL 61010-1; UL 61010-2-030
CAN/CSA
-C22.2 No.61010-1, CAN/CSA-C22.2 No.61010-2-030 and
CAN/CSA
-C22.2 No.61010-2-201
The technical data of the product is approved in accordance with UL.
For more information
about the UL database, see: www.ul.com.
Select
Online Certifications Directory and enter E496940 as UL File Number.
IND. CONT. EQ.
E496940

Preface
8Unrestricted SICAM A8000 Series, SICAM I/O Modules
DC8-012-2.06, Edition 09.2019
Symbols used on the I/O Modules
Symbol
Description
Warning, risk of electric shock
Caution, risk of danger. The documentation
must be observed.
WEEE marking
Protection class II / protective insulation
Protection class III / extra-low voltage
CE conformity
UL conformity
Symbols used in Connection Diagrams
Symbol Description Symbol Description
Functional earth (FE)
Protective earth (PE)

SICAM A8000 Series, SICAM I/O Modules Unrestricted 9
DC8-012-2.06, Edition 09.2019
Open Source Software
This product contains, among other things, Open Source Software developed by third parties.
The Open Source Software used in this product and the license agreements concerning this
software can be found in the Readme_OSS. These Open Source Software files are protected
by copyright.
Your compliance with those license conditions will entitle you to use the Open Source
Software as foreseen in the relevant license. In the event of conflicts between Siemens
license conditions and the Open Source Software license conditions, the Open Source
Software conditions shall prevail with respect to the Open Source Software portions of the
software. The Open Source Software is licensed royalty-free.
Insofar as the applicable Open Source Software License Conditions provide for it you can
order the source code of the Open Source Software from your Siemens sales contact -
against payment of the shipping and handling charges - for a period of at least 3 years since
purchase of the Product.
We are liable for this product including the Open Source Software contained in it pursuant to
the license conditions applicable to the Product. Any liability for the Open Source Software
beyond the program flow intended for this product is explicitly excluded. Furthermore any
liability for defects resulting from modifications to the Open Source Software by you or third
parties is excluded. We do not provide any technical support for this Product if it has been
modified.

Open Source Software
10 Unrestricted SICAM A8000 Series, SICAM I/O Modules
DC8-012-2.06, Edition 09.2019