Siemens KNX GAMMA AP 258E11 User manual

GAMMA instabus
Surface-mounting housing
AP 258E11
The surface-mounting housing is used for installing presence detector UP
258Dx1 as a surface-mounted device.
● No need to drill a conduit box
● Quick and easy installation of the presence detector
A6V14046257_en--_a Smart Infrastructure
2023-05-31 Building Products

2
Smart Infrastructure A6V14046257_en--_a
GAMMA instabus 2023-05-31
Characteristics
AP 258E11 is a surface-mounting housing of type B for presence detectors UP258D31, UP-
258D41, UP258D51 and UP258D61.
Functions
AP 258E11 is a surface-mounting housing of type B for presence detectors UP258D31, UP-
258D41, UP258D51 and UP258D61. The mounting plate supplied with the presence detect-
ors is required for installation and must be screwed onto the surface-mounting housing. This
type of mounting then allows the presence detectors to be affixed to the ceiling as surface-
mounted devices without the need for tools.
Type overview
Type Designation Item number KNX PL-Link
AP 258E11 AP 258E11 surface-
mounting housing type B
5WG1258-7EB11 No
Product documentation and support
Product documentation
Documents related the product, such as operating and installation instructions, application
program description, product database, additional software and CE declarations can be
downloaded from the following website:
http://www.siemens.com/gamma-td
Frequently asked questions
For frequently asked questions about the product and their solutions, see:
https://support.industry.siemens.com/cs/products?dtp=Faq&mfn=ps&lc=en-WW
FAQ
Support
Contact details for additional questions relating to the product:
Tel.: [phone]
http://www.siemens.com/supportrequest

3
Smart Infrastructure A6V14046257_en--_a
GAMMA instabus 2023-05-31
Notes
Security
CAUTION
National safety regulations
Failure to comply with national safety regulations may result in personal injury and property
damage.
● Observe national provisions and comply with the appropriate safety regulations.
Note on installation
The surface-mounting housing can be used for fixed installations indoors and in dry loca-
tions.
Commissioning
Mounting
Fig.1: Surface-mounting housing AP258E11
Process
1. Screw the surface-mounting housing into the ceiling using 2 Phillips screws
2. Pull the KNX cable through the mounting frame
3. Snap the mounting frame onto the mounting housing
Disposal
This symbol or any other national label indicate that the product, its
packaging, and, where applicable, any batteries may not be disposed of as
domestic waste. Delete all personal data and dispose of the item(s) at
separate collection and recycling facilities in accordance with local and
national legislation.
For additional details, refer to Siemens information on disposal.

4
Smart Infrastructure A6V14046257_en--_a
GAMMA instabus 2023-05-31
Technical data
Mechanical data
Housing material Plastic
Dimensions See Dimension drawing [}4]
Product weight 59 g
Fire load 3 MJ
Environmental conditions
Ambient temperature in operation -5 °C...+45 °C (23 °F...113 °F)
Storage temperature -20 °C...+70 °C (-4 °F...158 °F)
Transport temperature -25 °C...+70 °C (-13 °F...158 °F)
Relative humidity
(non-condensing)
5 %...95 %
Environmental rating EN 60721-3-3: Class 3k5
Protection settings
Test mark KNX, EAC, RCM, WEEE, China-RoHS
CE mark Yes
Dimension drawing
Fig.2: Surface-mounting housing AP258E11

5
Smart Infrastructure A6V14046257_en--_a
GAMMA instabus 2023-05-31
Compliance information
FCC Statement
WARNING
Installation and usage of equipment not in accordance with instructions manual may
result in:
Radiation of radio frequency energy
Interference to radio communications
● Install and use equipment in accordance with installation instructions manual
● Read the following information
This equipment generates, uses, and can radiate radio frequency energy and if not installed
and used in accordance with the instructions manual, may cause interference to radio com-
munications.
It has been tested and found to comply with the limits for a Class A computing device pursu-
ant to Part 15 of FCC Rules, which are designed to provide reasonable protection against
such interference when operated in a commercial environment.
Operation of this equipment in a residential area is likely to cause interference in which case
the user at his own expense will be required to take whatever measures may be required to
correct the interference.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reason-
able protection against harmful interference in a residential installation. This equipment gen-
erates, uses and can radiate radio frequency energy and, if not installed and used in accord-
ance with the instructions, may cause harmful interference to radio communications. How-
ever, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be de-
termined by turning the equipment off and on, the user is encouraged to try to correct the in-
terference by one or more of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
● Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause
undesired operation
FCC Caution: Changes or modifications not expressly approved by Siemens Switzerland
Ltd. could void the user’s authority to operate the equipment. United States representative
https://new.siemens.com/us/en/products/buildingtechnologies/home.html
Industry Canada statement
This device complies with ISED’s license-exempt RSSs. Operation is subject to the following
two conditions:
1. This device may not cause interference, and
2. This device must accept any interference received, including interference that may cause
undesired operation.

Issued by
Siemens Switzerland Ltd
Smart Infrastructure
Global Headquarters
Theilerstrasse 1a
CH-6300 Zug
[phone]
www.siemens.com/buildingtechnologies
© Siemens 2023
Technical specifications and availability subject to change without notice.
Document ID A6V14046257_en--_a
Edition 2023-05-31