Siemens SCALANCE X005 User manual

SCALANCE X005 / X005TS
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
___________________
SIMATIC NET
Industrial Ethernet switches
SCALANCE X005 / X005TS
Operating Instructions
07/2014
C79000
-G8976-C344-01
Introduction
1
Network topologies
2
Description of the device
3
Mounting
4
Connecting up
5
Maintenance and
troubleshooting
6
Technical specifications
7
Approvals
8
Dimension drawings
9

Siemens AG
Industry Sector
Postfach 48 48
90026 NÜRNBERG
GERMANY
C79000-G8976-C344-01
Ⓟ
07/2014 Subject to change
Copyright © Siemens AG 2010 - 2014.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by
personnel qualified
for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

SCALANCE X005 / X005TS
Operating Instructions, 07/2014, C79000-G8976-C344-01 3
Table of contents
1 Introduction............................................................................................................................................. 5
1.1 On the Operating Instructions ........................................................................................................5
1.2 On the product ...............................................................................................................................7
1.3 Unpacking and checking................................................................................................................8
2 Network topologies ................................................................................................................................. 9
3 Description of the device....................................................................................................................... 11
3.1 Overview SCALANCE X-000.......................................................................................................11
3.2 Product characteristics.................................................................................................................12
3.3 TP ports (twisted pair)..................................................................................................................13
3.4 LEDs ............................................................................................................................................15
4 Mounting............................................................................................................................................... 17
4.1 Types of installation .....................................................................................................................17
4.2 Installation on a DIN rail...............................................................................................................18
4.3 Installation on a standard rail .......................................................................................................20
4.4 Wall mounting ..............................................................................................................................21
5 Connecting up....................................................................................................................................... 23
5.1 Power supply................................................................................................................................23
5.2 Grounding ....................................................................................................................................24
5.3 IE FC RJ-45 Plug 180 ..................................................................................................................24
6 Maintenance and troubleshooting.......................................................................................................... 27
7 Technical specifications ........................................................................................................................ 29
8 Approvals.............................................................................................................................................. 31
8.1 Approvals_intro_X-000.................................................................................................................31
8.2 Note for Australia .........................................................................................................................32
8.3 Notes on the cULus approval.......................................................................................................32
8.4 Notes on the e1/E1 approval of the SCALANCE X005TS...........................................................32
8.5 Noise test of the SCALANCE X005TS ........................................................................................33
8.6 Overvoltage test of the SCALANCE X005TS ..............................................................................33
8.7 Mechanical stability (in operation)................................................................................................33
9 Dimension drawings.............................................................................................................................. 35
Index..................................................................................................................................................... 37

Table of contents
SCALANCE X005 / X005TS
4Operating Instructions, 07/2014, C79000-G8976-C344-01

SCALANCE X005 / X005TS
Operating Instructions, 07/2014, C79000-G8976-C344-01 5
Introduction
1
1.1
On the Operating Instructions
Purpose of the Operating Instructions
These operating instructions support you when commissioning the unmanaged Industrial
Ethernet entry level switches SCALANCE X005 and SCALANCE X005TS (Transportation
System).
Validity of the Operating Instructions
These operating instructions are valid for the following devices:
Device
Order number
SCALANCE X005
6GK5005-0BA00-1AA3
SCALANCE X005TS
6GK5005-0BA00-1CA3
Further documentation
The "SIMATIC NET Industrial Ethernet Twisted Pair and Fiber Optic Networks" manual
contains additional information on other SIMATIC NET products that you can operate along
with the SCALANCE X005 and SCALANCE X005TS IE switches in an Industrial Ethernet
network.
You can order the manual "SIMATIC NET Industrial Twisted Pair and Fiber Optic Networks",
release 05/2001, using the following order numbers:
6GK1970-1BA10-0AA0 German
6GK1970-1BA10-0AA1 English
6GK1970-1BA10-0AA2 French
6GK1970-1BA10-0AA4 Italian
You will also find this network manual on the Internet pages of Service & Support under the
following entry ID: 1172207 (http://support.automation.siemens.com/WW/view/en/1172207).
You will find further information in the "System Manual Industrial Ethernet" in the Manual
Collection.
You will find further information on the SCALANCE system on the Internet at
www.siemens.com/scalance (www.siemens.com/scalance).
Audience
These Operating Instructions are intended for persons who commission networks with the IE
switches of the SCALANCE X-000 product line.

Introduction
1.1 On the Operating Instructions
SCALANCE X005 / X005TS
6Operating Instructions, 07/2014, C79000-G8976-C344-01
SIMATIC NET glossary
Explanations of many of the specialist terms used in this documentation can be found in the
SIMATIC NET glossary.
You will find the SIMATIC NET glossary here:
●SIMATIC NET Manual Collection or product DVD
The DVD ships with certain SIMATIC NET products.
●On the Internet under the following entry ID:
50305045 (http://support.automation.siemens.com/WW/view/en/50305045)
Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, solutions, machines, equipment and/or networks. They are
important components in a holistic industrial security concept. With this in mind, Siemens’
products and solutions undergo continuous development. Siemens recommends strongly
that you regularly check for product updates.
For the secure operation of Siemens products and solutions, it is necessary to take suitable
preventive action (e.g. cell protection concept) and integrate each component into a holistic,
state-of-the-art industrial security concept. Third-party products that may be in use should
also be considered. For more information about industrial security, visit
http://www.siemens.com/industrialsecurity.
To stay informed about product updates as they occur, sign up for a product-specific
newsletter. For more information, visit http://support.automation.siemens.com.

Introduction
1.2 On the product
SCALANCE X005 / X005TS
Operating Instructions, 07/2014, C79000-G8976-C344-01 7
1.2
On the product
What is possible?
The SCALANCE X005 and SCALANCE X005TS IE switches allow the cost-effective
installation of small Industrial Ethernet linear bus or star structures with switching
functionality. The devices are designed for installation in a cabinet.
Note
It is not possible to use a SCALANCE
X005 or SCALANCE X005TS in a redundant ring
because they do not support redundancy.
Note
If devices are supplied over long 24 V power supply lines or networks, measures are
necessary to prevent interference by strong electromagnetic pulses on the supply lines.
These can result, for example, due to lightning or switching of large inductive load
s.
One of the tests used to attest the immunity of these devices to electromagnetic interference
is the "surge immunity test" according to EN 61000
-4-5. This test requires overvoltage
protection for the power supply lines. A suitable device is, for exampl
e, the Dehn Blitzductor
BVT AVD 24 V type no. 918 422 or a comparable protective element.
Manufacturer:
DEHN+SÖHNE GmbH+Co.KG Hans Dehn Str.1 Postfach 1640 D
-92306 Neumarkt,
Germany
Components of the product
The following components are supplied with a SCALANCE X005 or SCALANCE X005TS:
●SCALANCE X005 or SCALANCE X005TS IE switch
●2-terminal plug-in block (power supply)
●Product information

Introduction
1.3 Unpacking and checking
SCALANCE X005 / X005TS
8Operating Instructions, 07/2014, C79000-G8976-C344-01
Accessories
Component
Packaging unit
Order number
IE FC Stripping Tool
1
6GK1901-1GA00
IE FC blade cassettes
1
6GK1901-1GB00
IE FC TP standard cable GP
1
6XV1840 2AH10
IE FC TP trailing cable
1
6XV1840-3AH10
IE FC TP marine cable
1
6XV1840-4AH10
IE FC TP trailing cable GP
1
6XV1870-2D
IE FC TP flexible cable GP
1
6XV1870-2B
IE FC RJ-45 Plug 180
1
6GK1 901-1BB10-2AA0
IE FC RJ-45 Plug 180
10
6GK1 901-1BB10-2AB0
IE FC RJ-45 Plug 180
50
6GK1 901-1BB10-2AE0
1.3
Unpacking and checking
Unpacking and checking
WARNING
Do not use any parts that show evidence of damage
If you use damaged parts, there is no guarantee that the device will function according to
the specification.
If you use damaged parts, this can lead to the following problems:
•Injury to persons
•Loss of the approvals
•Violation of the EMC regulations
•Damage to the device and other components
Use only undamaged parts.
1. Make sure that the package is complete.
2. Check all the parts for transport damage.
WARNING
If the SCALANCE X005TS device is operated in an ambient temperature of between 60 ℃
and 65 °C, the temperature of the device housing may be higher than 65 ℃. The device
must therefore be installed so that it is only accessible to service personnel or users that
are aware of the reason for restricted access and the required safety measures at an
ambient temperature of 60 ℃to 65 °C.

SCALANCE X005 / X005TS
Operating Instructions, 07/2014, C79000-G8976-C344-01 9
Network topologies
2
Switching technology allows extensive networks to be set up with numerous nodes and
simplifies network expansion.
Which topologies can be implemented?
Using the SCALANCE X005 and SCALANCE X005TS IE switches, you can implement star
topologies.
Note
Keep to the maximum permitted cable lengths of the devices you are using. You will find the
permitted cable lengths in the section "
Technical specifications (Page 29)".
Star topology
Figure 2-1 Example of a star topology with SCALANCE X005

Network topologies
SCALANCE X005 / X005TS
10 Operating Instructions, 07/2014, C79000-G8976-C344-01

SCALANCE X005 / X005TS
Operating Instructions, 07/2014, C79000-G8976-C344-01 11
Description of the device
3
3.1
Overview SCALANCE X-000
Table 3- 1 Overview of the product characteristics
X005
X005TS
SIMATIC environment
+
+
Diagnostics LED
+
+
24 VDC
+
+
2 x 24 VDC
-
-
Compact housing
(securing collar, etc.)
+ +
Signaling contact + on-site operation
-
-
Diagnostics: Web, SNMP, PROFINET
-
-
C-PLUG
-
-
Ring redundancy with RM
-
-
Passive ring redundancy
-
-
Standby redundancy
-
-
IRT capability
-
-
Fast learning
-
-
Passive listening
-
-
Log table
-
-
SNTP + SICLOCK - -
Cut Through
-
-
Table 3- 2 Overview of the connection options
X005
X005TS
TP (RJ-45)
Fast Ethernet 10 / 100 Mbps
5 5

Description of the device
3.2 Product characteristics
SCALANCE X005 / X005TS
12 Operating Instructions, 07/2014, C79000-G8976-C344-01
3.2
Product characteristics
Possible attachments
The SCALANCE X005 and SCALANCE X005TS have five RJ-45 jacks for connection of end
devices or other network segments.
Figure 3-1 SCALANCE X005
Note
The SCALANCE X005 shown above has the same construction as the SCALANCE X005TS.

Description of the device
3.3 TP ports (twisted pair)
SCALANCE X005 / X005TS
Operating Instructions, 07/2014, C79000-G8976-C344-01 13
3.3
TP ports (twisted pair)
RJ-45 connector pinout
With SCALANCE X005 and SCALANCE X005TS, the twisted-pair ports are designed as RJ-
45 jacks with MDI-X pin assignment (Medium Dependent Interface Autocrossover) of a
network component.
Pin number
Assignment
Pin 8
n. c.
Pin 7
n. c.
Pin 6
TD-
Pin 5
n. c.
Pin 4
n. c.
Pin 3
TD+
Pin 2
RD-
Pin 1
RD+
Note
Permitted cable lengths
TP cords or TP
-XP cords with a maximum length of 10 m can be connected to the TP port
with RJ
-45 jacks.
With the IE FC cables and IE FC RJ
-45 plugs 180, an overall cable length of a maximum of
100 m is permitted between two devices depending on the cable type.
Autonegotiation
With the autonegotiation mechanism, repeaters and end devices can automatically
determine the transmission speed and the transmission mode of the partner port. This
makes it possible to configure different devices automatically.
Two components connected to a link segment can exchange information about the data
transfer and can adapt their settings to each other. The mode with the highest possible
speed is set.
Note
Devices not supporting autonegotiation must be set permanently to 100
Mbps half duplex or
10
Mbps half duplex.

Description of the device
3.3 TP ports (twisted pair)
SCALANCE X005 / X005TS
14 Operating Instructions, 07/2014, C79000-G8976-C344-01
Auto polarity exchange
If the pair of receiving cables is connected incorrectly (RD+ and RD- interchanged), the
polarity is adapted automatically.
Note
The SCALANCE
X005 and SCALANCE X005TS IE switches are plug-and-play devices that
require no settings during commissioning.
MDI / MDI-X autocrossover function
With the MPI/MDI-X autocrossover function, the send and receive contacts of an Ethernet
port are assigned automatically. The assignment depends on the cable with which the
communications partner is connected. This means that it does not matter whether the port is
connected using a patch cable or crossover cable. This prevents malfunctions resulting from
mismatching send and receive lines. This makes installation much easier for the user.
The SCALANCE X005 and SCALANCE X005TS devices support the MDI / MDI-X
autocrossover function.
Insulation between the TP ports
There are two TP port groups:
Group 1: P1
Group2: P2 to P5
Between ports of different port groups, an insulation voltage of 1.5 kV is adhered to
(corresponds to IEEE802.3, Chapter 33.4.1.1, Environment B), e.g. between P1 and P2.
The requirements for Environment A are met between ports of the same group, e.g. between
P2 and P5.
NOTICE
Setting ports with a fixed configuration
Ports of partner stations with a fixed configuration must be set to 100 Mbps/ half duplex or
10 Mbps half duplex.
NOTICE
Formation of loops
Note that the direct connection of two ports or accidental connection over several switches
causes an illegal loop that can cause network overload and failure.

Description of the device
3.4 LEDs
SCALANCE X005 / X005TS
Operating Instructions, 07/2014, C79000-G8976-C344-01 15
3.4
LEDs
Power LED "L" (green LED)
The power LED shows the status of the power supply.
LED color
LED status
Meaning
Green
Lit
Power supply is connected.
-
Off
Power supply is not connected or <14 V.
Port LEDs "P" (green/yellow LEDs)
The port LEDs indicate the status of the ports.
LED color
LED status
Meaning
Green
Lit
TP link exists, no data reception at port
Yellow
Lit
TP link exists, data reception at port
Yellow
Flashing
Test phase during power on

Description of the device
3.4 LEDs
SCALANCE X005 / X005TS
16 Operating Instructions, 07/2014, C79000-G8976-C344-01

SCALANCE X005 / X005TS
Operating Instructions, 07/2014, C79000-G8976-C344-01 17
Mounting
4
4.1
Types of installation
The devices can be installed in the following ways:
●Installation on a 35 mm DIN rail
●Installation on a SIMATIC S7-300 standard rail
●Wall mounting
WARNING
Ambient temperature between 60 °C and 65 °C
If a device is operated in an ambient temperature between 60 ℃and 65 °C, the
temperature of the device housing may be higher than 70 °C. The device must therefore be
installed so that it is only accessible to service personnel or users that are aware of the
reason for restricted access and the required safety measures at an ambient temperature
of 60 ℃to 65 °C.
WARNING
If the cable or conduit entry point exceeds 70 °C or the branching point of conductors
exceeds 80 °C, special precautions must be taken. If the equipment is operated in an air
ambient in excess of 50 °C to 60 °C, only use cables with admitted maximum operating
temperature of at least 80 ℃.
WARNING
Protective measures need to be taken to ensure that the rated voltage of the equipment
cannot be exceeded by more than 40% by transient surges. This is achieved by operating
the equipment only with SELV circuits (previously also PELV). Under no circumstances
must transient surges exceed 119 V.
Note
When installing and operating the device, keep to the installation instructions and safety
-
related notices as described here and in the manual "SIMATIC NET Industrial Ethernet
Twisted Pair and Fiber Optic Networks".
Note
Provide suitable shade to protect the device against direct sunlight. This avoids unwanted
warming of the device and prevents premature aging of the device and cabling.

Mounting
4.2 Installation on a DIN rail
SCALANCE X005 / X005TS
18 Operating Instructions, 07/2014, C79000-G8976-C344-01
4.2
Installation on a DIN rail
Mounting
To install the device on a 35 mm DIN rail complying with DIN EN 50022, follow the steps
below:
1. Place the second housing guide of the device on the top edge of the DIN rail.
2. Press the device down against the DIN rail until the spring catch locks in place.
3. Fit the connectors for the power supply. See also section "Power supply (Page 23)".
4. Insert the terminal block into the sockets on the device.
Figure 4-1 Installation on a 35 mm DIN rail

Mounting
4.2 Installation on a DIN rail
SCALANCE X005 / X005TS
Operating Instructions, 07/2014, C79000-G8976-C344-01 19
Removal
To remove the device from the DIN rail, follow the steps below:
1. Disconnect all connected cables.
2. Pull out the terminal block for the power supply.
3. Release the DIN rail catch on the bottom of the device using a screwdriver.
4. Pull the lower part of the device away from the DIN rail.
Figure 4-2 Removal from a 35 mm DIN rail

Mounting
4.3 Installation on a standard rail
SCALANCE X005 / X005TS
20 Operating Instructions, 07/2014, C79000-G8976-C344-01
4.3
Installation on a standard rail
Installation on a SIMATIC S7-300 standard rail
To install the device on an S7-300 standard rail, follow the steps below:
1. Place the first housing guide of the device on the top edge of the S7-300 standard rail.
2. Screw the device to the underside of the standard rail (tightening torque 2 Nm).
3. Fit the connectors for the power supply. See also section "Power supply (Page 23)".
4. Insert the terminal block for the power supply into the socket on the device.
Figure 4-3 Installation on a SIMATIC S7-300 standard rail
Removal
To remove the device from the S7-300 standard rail, follow the steps below:
1. Disconnect all connected cables.
2. Release the screw on the bottom of the standard rail.
3. Remove the device from the standard rail.