SIIG 13" User manual

1
Triple Monitor Desk Stand - 13" to 24"
Installation Instructions
04-0884A

2
Unpacking
• Carefully remove the contents and lay out on cardboard or other protective surface
• Check package contents against the parts list to ensure that all components were received
undamaged. Do not use damaged or defective parts
• Carefully read all instructions before attempting installation
Safety Information
• Use proper safety equipment during installation
• If you don't understand the installation instructions, please consult an installation
specialist
• This mount contains small parts which can act as a choking hazard if swallowed
• Do not use this product for any purpose or in any configuration not explicitly specified
in these instructions
Tools Required
• Phillips screwdriver
• 3/8" drill bit (for Grommet installation)
• Electric drill (for Grommet installation)
Parts List
a - (1x) 48mm
TubeSupport
c1 - (2x) Side
Vesa Plate
e - (1x) Arm
ConnectPlate
i - (2x) Arm Plastic
Cover
j - (3x) M6x29
Bolt
k - (1x) Decorative
Cover
l - (1x) Grommet
Plate
m - (1x) Grommet
Bolt
n - (1x) Wing
Nut
o - (3x) Allen
Key
p - (24x) M4
Washer
b - (1x) Weighted
Base
d - (2x) Curved
Arm
f - (1x) Arm
Clamp
g - (4x) M6x25
Bolt
h - (4x) M6
Washer
r - (12x) M4x30
Bolt
s - (12x) M4
Spacer
t - (2x) M8x10
Bolt
u - (2x) Wire
clip
q - (12x) M4x12
Bolt
c2 - (1x) Middle VESA
Plate
v - (2x) M4x16
Bolt with Washer

3
Installation
The Monitor Desk Stand can be free standing (Weighted Base Installation) or permanently
attached to the desktop (Grommet Hole Installation).
Step 1 - Mounting the Tube Support
1a) Weighted Base Installation
For free standing, simply mount the 48mm Tube Support (a) to the Weighted Base (b) using
M6x29 Bolts (j) then slide the Decorative Cover (k) onto the tube support as show in Figure
1a. Then continue to Step 2.
Figure 1a

4
1b) Grommet Hole Installation
This installation requires you to either drill a 3/8" (10mm) diameter hole through the desktop
or use an existing grommet hole. If the existing grommet hole comes with a plastic protector,
remove it to ensure a flat surface before installing.
Mount the 48mm Tube Support (a) using Grommet Bolt (m), Grommet Plate (l) and secure
with Wing Nut (n), then slide the Decorative Cover (k) onto the tube support as shown in
Figure 1b. Then continue to Step 2.
Figure 1b

5
Figure 2a
Step 2 - Assemble Curved Arms and Install it onto the Tube Support
1. Assemble theCurved Arms (d), Arm Connector Plate (e), Arm Clamp (f)and fasten with
M6x25 Bolts (g) and M6 Washers (h) using Allen Key (o) as shown in Figure 2a.
Important: Position the Arm Connector Plate (e) so that the screw holes are oriented to the
bottom.

6
Figure 2b
2. Mount the Arm Assembly to the tube support, fasten it using M8x10 Bolts (t) with Allen
Key (o) and insert the Wire Clips (u) as shown in Figure 2b. Then continue to Step 3.

7
Figure 3a
Step 3 - Mounting the VESA Plate to the Monitor
3a) For Flat Back Monitors
MounttheVESA Plates (c1 & c2) using M4x12 Bolts(q) andM4 Washers (p) asshowninFigure
3a. Then continue to Step 4.

8
3b) For Curved Back Monitors
Mount the VESA Plates (c1 & c2) using M4x30 Bolts(r) and M4 Washers (p) as shown in Figure
3b. Then continue to Step 4.
Figure 3b

9
Step 4 - Mounting the Monitors and Adjusting the Tilt Angle
1. Attach the Middle VESA Plate (c2) with Monitor Assembly and secure it using M4x16
Bolt with Washers (v), then slide the Side VESA Plate (c1) with Monitor Assemblies onto
the Arm Assembly and secure by rotating the Plastic Knob. Install the Arm Plastic
Covers (i) onto the Arm Assembly as shown in Figure 4a.
Caution: For Weighted Base Installation, we suggest you have a helper hold the desk
stand upright while attaching your monitors to prevent damage to the monitor or desk
stand and ensure your personal safety.
Figure 4a

10
2. Adjust the monitor's tilt angle, use the Allen Key (o) to loosen the Grub Screw, then
tighten the Grub Screw to fix the tilt angle as shown in Figure 4b.
Figure 4b