SIIG Security Countertop Kiosk & POS Stand for... User manual

1
Security Countertop Kiosk & POS
Stand for iPad
Installation Instructions
04-1047C

2
Unpacking
• Carefully remove the contents and lay them out on cardboard or other protective
surface
• Check package contents against the parts list to ensure that all components were
received and undamaged. Do not use damaged or defective parts
• Carefully read all instructions before attempting the installation
Safety Information
• Use proper safety equipment during installation
• If you don't understand the installation instructions, please consult an installation
specialist
• This stand contains small parts which can act as a choking hazard if swallowed
• Do not use this product for any purpose or in any conguration not explicitly
speciedintheseinstructions
Tools Required
• Phillips screwdriver
• Electric drill, 3/16" drill bit and 3/8" masonry drill bit for permanent wood or
concrete/brick installation respectively
Parts List
B-(1x)SupportPole C-(1x)WeightedBase
K-(1x)4mmAllenKey L-(1x)5mmAllenKey
A-(1x)iPadHolder
F-(2x)Screw H-(2x)Key
J-(4x)M8x20Bolt
G-(2x)ConcreteAnchor
I-(4x)M5x6Bolt
D-(4x)RubberPad
M-(1x)PlasticButton
E-(1x)DecorativeCover
(2x)5mmFoamPad

3
Installation
Step 1 - Mount the Rubber Pads to the Weighted Base
1. Turn the weight base so that the countersinked holes are facing up.
2. RemovetheadhesiveprotectionfromtheRubber Pads (D).
3. MounttheRubber Pads (D) onto the weighted base, see Figure 1.
Figure 1
Step 2 - Mount the Support Pole to the Weighted Base
1. Install the Decorative Cover (E) and Support Pole (B) to the Weighted Base (C),
secure them using M8x20 Bolt (J), tighten each bolt with Allen Key (L) by turning
it clockwise until fully tight, see Figure 2.
Figure 2

4
Step 3 - Mounting to the Countertop
3A) Weighted Base Installation
Simplyplacethestanddirectlyontothecountertop.
The weighted base will secure the stand, see Figure 3A.
3B) Permanent Wood Countertop Installation
1. Place the stand in the desired position. Lift up the decorative cover and mark the
left and right positions of the mounting holes, see Figure 3B.
2. Removethestand.
3. Next, pre-drill a 3/16" hole to a depth of approximately 2.2" into the wood
countertop at each marked location.
4. Movethestandbackontothecountertopandlineupthemountingholeswiththe
drilled holes.
5. Foreachlocation,insertScrew (F)intothewoodcountertop.Tighteneachscrew
with a Phillips screwdriver by turning it clockwise until fully tight.
6. Lower the decorative cover to it's original position.
Figure 3A
Figure 3B

5
Figure 3C
3C) Permanent Concrete/Brick Countertop Installation
1. Place the stand in the desired position. Lift up the decorative cover and mark the
left and right positions of the mounting holes, see Figure 3C.
2. Removethestand.
3. Drill holes using an electric drill and a 3/8" masonry drill bit to a depth of
approximately2.4"intotheconcrete/brickcountertopateachmarkedlocation.
4. InsertaConcrete Anchor (G) into each drilled hole. If necessary, a hammer can
beusedtolightlytapeachconcreteanchorintoplacesothattheyareushwith
the countertop.
5. Once all of the concrete anchors are in place, move the stand back onto the
countertop and line up the mounting holes with the drilled holes.
6. For each location, insert Screw (F)into theconcreteanchor.Tighteneachscrew
with a Phillips screwdriver by turning it clockwise until fully tight.
7. Lower the decorative cover to it's original position.

6
Step 4 - Mounting the iPad Holder
1. If the cover is locked to the holder, insert Key (H) into the security lock and turn it
counterclockwise to unlock, then remove the cover, see Figure 4A.
2. Place the holder so that the security lock is on the top.
3. SecuretheholdertothesupportpoleusingM5x6 Bolt (I), see Figure 4B.
4. TighteneachboltwithaPhillipsscrewdriverbyturningitclockwiseuntilfullytight.
Figure 4B
Figure 4A

7
Step 5 - Arranging the iPad Mount
5A) For iPad 2 / 3 / 4
TheSiliconPosts comepre-conguredto tiPad2 /3/ 4models.No adjustmentis
needed for use with these iPad models.
1. Replace the currently mounted 7mm Foam Pads with the included 5mm Foam
Pads, see Figure 5A.
Figure 5A
5B) For iPad Air / Air 2
1. RemovetheSiliconePostsfromtheiroriginalpositions,seeFigure 5B-1.
2. InstalltheSiliconePostsatthepositionsshown,seeFigure 5B-2 and Figure 5B-3.
Figure 5B-1
SiliconePost
SiliconePost
SiliconePost
SiliconePost
SiliconePost
SiliconePost
SiliconePost
SiliconePost
Figure 5B-2 Figure 5B-3
Foam Pad
Foam Pad
SiliconePost
SiliconePost
SiliconePost
SiliconePost

8
Step 6 - Installing iPad
1. Place your iPad into the holder so that it rests on the foam pads and is supported
bytheSiliconPosts.
2. Connect the iPad's charging cable and route the cable through the cable
management slot, see Figure 6.
Figure 6
Step 7 - Installing the Cover onto the iPad Holder
1. Insert the Key (H) into the lock, turn it counterclockwise to unlock, see Figure 7.
2. Aligntheslotsonthe bottomofthecoverto theopeningsin thebottomofthe
holder, then pivot the cover onto the holder, see Figure 8.
3. Turn the key clockwise to secure the cover to the holder, remove the key from the
lock.
Figure 7 Figure 8

9
Step 8 - Final Adjustments
Tilt Angle Adjustment
1. Adjustthetightnessoftiltangleusing4mm Allen Key (K), see Figure 9.
Figure 9
Rotation Adjustment (Optional)
1. RemovetheiPadfromtheholder.
2. Using a Phillips screwdriver, turn the screws clockwise to tighten and
counterclockwise to loosen, see Figure 10.
Figure 10
RotationAdjustmentScrew
RotationAdjustmentScrew
RotationAdjustmentScrew

10
Disable the Home Button
1. RemovetheiPadHolder'scover.
2. RemovetheSiliconebuttonfromthecover.
3. Insert the the Plastic Button (M)intotheopening,seeFigure 11.
4. Reinstallthecoverandlockitinplace.
Figure 11
Maintenance
Check the mounting hardware every two months for tightness.
Viewing Angle Adjustment
Thisstandallowstiltviewingangleof0to-75degreesandrotationviewingangleof
0to90degrees,seeFigure 12.
Figure 12