SIIG CE-MT2912-S1 User manual

2
Unpacking
• Carefully remove contents and lay out on cardboard or other protective surface
• Check package contents against the parts list to ensure that all components were received
undamaged. Do not use damaged or defective parts
• Carefully read all instructions before attempting installation
Parts List
a - (4x) M8x60 Metal anchor b - (1x) Plastic washer c - (4x) M3 at washer
e - (4x) M5 at washer
d - (4x) M4 at washer
f - (4x) M3 x 10 Bolt g - (4x) M4 x 10 Bolt h- (4x) M5 x 10 Bolt
i - (1x) Allen Wrench j - (1x) Spanner (S=13) k - (4x) Short joining patch
Note
This installation manual is intended for all SIIG adjustable height ceiling projector mounts.
l - (1x) Tube m - (4x) Mounting legs

3
Installation
Caution: This projector mount must be securely attached to ceiling. If the mount is not
properly installed it may fall, resulting in possible injury and/or damage. SIIG, Inc. is NOT
RESPONSIBLE for any damage or injury caused by incorrect installation, assembly or use
Note: The mounting components and hardware supplied in this package are not designed
for installations to ceilings with steel studs. If the hardware you need for your installation is
not included, please consult your local hardware store for proper mounting hardware for the
application.
Step 1 - Installing the Tube to Ceiling
Important: Don't loosen the two side nuts at the same time after nishing the installation for
fear that the mount drops.
1. Place the Tube Support's mounting plate in the desired position on the ceiling, using the
mounting plate as a template mark 4 holes, then remove the tube support.
2. Using a 10mm drill bit drill 4 holes 50mm deep in the marked positions. Note: The holes
should be drilled symmetrical in horiziontal and vertical direction.
3. Insert four metal anchors into the drilled holes until ush with the ceiling, then tighten
the nut slightly to secure the steel anchor to the ceiling. Remove the at washers,spring
washers and nuts from the steel anchors.
4. Place the mounting plate on the four metal anchors,and install the at washers,spring
washers and nuts and tighten them until hand tight.
Note:Each nut should be tightened so the steel anchor and the tube support are securely
fastened to the ceiling, do not over tighten.
Figure 1
A
Ceiling
Tube

4
Step 2 - Installing the Mounting Legs on the Projector
1. When installing the mounting legs to the projector, the four Z-shaped connecting arms
should be adjusted to match the mounting holes on the projector.
2. Select the mounting screws according to the size of the thread holes in the projector,
place the projector as close to the center of gravity as possible.
3. Once all screws are in place, tighten them using a Phillips screwdriver until hand tight, do
not overtighten.
F/G/H
C/D/E
Figure 2

5
Step 3 - Connecting the Projector Plate to the Tube Support
Important: Don't loosen the two side knobs at the same time for fear that the mount drops.
1. Loosen the 2 knobs on the sides of the projector plate rst, don't remove the knobs
completely from the projector plate.
2. Put the Plastic Washer (B) into the mounting leg as shown, the plastic washer allows for
smooth tilt and rotation of the projector.
3. Mount the projector plate to the tube support and tighten the two knobs hand tight to
secure it.
Figure 3
Ceiling
B

6
CEILING
Step 4 - Final Installation and Adjustment
1. Adjust the height of the projector by holding the projector in one hand while removing
the 3 Height Adjustment Bolts, raise or lower the projector to the desired height. Once
the desired height is attained, reinstall the height adjustment bolts and fully tighten them
to secure the projector.
2. Adjust the angle and direction of the projector by rmly grasping the projector with both
hands and slowly tilting it forward, backward, side-to-side, and rotate.
Figure 4
Height Adjustment Bolts

7
Blank Page

About SIIG, Inc.
Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity solutions (including Serial ATA
and Ultra ATA Controllers, FireWire, USB, and legacy I/O adapters) that bridge the connection between
Desktop/Notebook systems and external peripherals. SIIG continues to grow by adding A/V and Digital
Signage connectivity solutions to our extensive portfolio.
SIIG products offer comprehensive user manuals, many user-friendly features, and are backed by an extensive
manufacturer warranty. High quality control standards are evident by the overall ease of installation
and compatibility of our products, as well as one of the lowest defective return rates in the industry. SIIG
products can be found in computer retail stores, mail order catalogs, through major distributors, system
integrators, and VARs in the Americas and the UK, and through e-commerce sites.
Universal Height Adjustable Projector Ceiling Mount - Black is a trademark of SIIG, Inc. SIIG and the SIIG
logo are registered trademarks of SIIG, Inc. All other names used in this publication are for identication
only and may be trademarks of their respective owners.
April, 2018 Copyright © 2018 by SIIG, Inc. All rights reserved.
PRODUCT NAME
Universal Height Adjustable Projector Ceiling Mount - Black
Technical Support and Warranty
QUESTIONS? SIIG’s Online Support has answers! Simply visit our web site at www.siig.com and click Support. Our
online support database is updated daily with new drivers and solutions. Answers to your questions could be just a few
clicks away. You can also submit questions online and a technical support analyst will promptly respond.
SIIG offers a 3-year manufacturer warranty with this product. This warranty covers the original purchaser and
guarantees the product to be free of any defects in materials or workmanship for three (3) years from the date of purchase
of the product.
SIIG will, at our discretion, repair or replace (with an identical product or product having similar features and
functionality) the product if defective in materials or workmanship. This warranty gives you specic legal rights, and
you may also have other rights which vary from state to state. Please see our web site for more warranty details.
If you encounter any problems with this product, please follow the procedures below.
A) If it is within the store's return policy period, please return the product to the store where you purchased from.
B) If your purchase has passed the store's return policy period, please follow the steps below to have the product repaired
or replaced.
Step 1: Submit your RMA request.
Go to www.siig.com, click Support, then REQUEST A PRODUCT REPLACEMENT to submit a request to SIIG
RMA or fax a request to 510-657-5962. Your RMA request will be processed, if the product is determined to be
defective, an RMA number will be issued.
Step 2: After obtaining an RMA number, ship the product.
• Properly pack the product for shipping. All accessories that came with the original package must be included.
• Clearly write your RMA number on the top of the returned package. SIIG will refuse to accept any shipping
package, and will not be responsible for a product returned without an RMA number posted on the outside of the
shipping carton.
• You are responsible for the cost of shipping to SIIG. Ship the product to the following address:
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
RMA #:
• SIIG will ship the repaired or replaced product via Ground in the U.S. and International Economy outside of the U.S.
at no cost to the customer.