SIKA Chamber User manual

Sika Technology Limited: Modular Assembly 1200x600x700 Intellectual Property Rights May Apply Page 1 of 6
April 2014 www.sikatech.co.nz ST-PD015-01
___________________________________________________________________________________
Modular Aluminium Jointing Chamber 1200 x 600 x 700 / 900H
ASSEMBLY INSTRUCTIONS
___________________________________________________________________________________
Chamber Rating: CLASS D - 210kN - AS3996:2006
Sika ‘Chambers’ are used for both Pathway & Roadway Installations
Chamber 1200 x 600 x 700H

Sika Technology Limited: Modular Assembly 1200x600x700 Intellectual Property Rights May Apply Page 2 of 6
April 2014 www.sikatech.co.nz ST-PD015-01
1. Place the chamber base on a flat area adjoining the pit or on a prepared bed of imported material in the
excavated pit. Note the “1200 x 600”script will be face up.
Chamber Base Studs
“1200 x 600” Identification Chamber Base
Fig 1
2. Where there is existing ducting and minimal side excavation is required use a split base. Ref Fig 2
Split Base Optional
Fig 2

Sika Technology Limited: Modular Assembly 1200x600x700 Intellectual Property Rights May Apply Page 3 of 6
April 2014 www.sikatech.co.nz ST-PD015-01
3. Remove the plastic tubes protecting the 4 –M10 studs protruding from the chamber base and place the
two chamber sides into place.
Insert the two chamber sides into the appropriately marked positions on the chamber base. Chamber
side supports cast into the chamber base will hold the chamber sides vertical until the 4 –M10 nuts
and washers are applied to hold them down. (Do not tighten these yet.)
Chamber Side
“1200x600” Identification
Chamber Base Studs
Chamber Side Supports Fig 3
4. Add the two chamber ends 600 and secure them with the 8 –M10 x 30 bolts and washers.
(Now tighten all the aforementioned fixings.)
Chamber End 600
Fig 4

Sika Technology Limited: Modular Assembly 1200x600x700 Intellectual Property Rights May Apply Page 4 of 6
April 2014 www.sikatech.co.nz ST-PD015-01
Duct Entry Panel
5. Apply the two polypropylene duct entry panels to each end recess and secure each one with 7 - M10 x
30 bolts and washers supplied.
Fig 5a
Fig 5b
Chamber 1200 x 600 x 700H

Sika Technology Limited: Modular Assembly 1200x600x700 Intellectual Property Rights May Apply Page 5 of 6
April 2014 www.sikatech.co.nz ST-PD015-01
Chamber Extension 200mm
6. Assemble chamber extension as per Fig 6a using 8 - M10 x 30 bolts and washers supplied. Place on top
of chamber flange. See arrows for right way up.
Chamber Extension
1200 x 600 x 200H
Fig 6a
Chamber Extension
1200 x 600 x 200H
Chamber Extension Locator Lug will Self Align Extension
Chamber 1200 x 600 x 700H
Fig 6b
Bolt assembled chamber extension to the chamber
with the 4 –M16x40 bolts, nuts and spring washers
supplied.
Chamber 1200 x 600 x 700H
& Extension 1200 x 600 x 200H
Fig 6c
Chamber 1200 x 600 x 700HChamber 1200 x 600 x 700H
Arrows

Sika Technology Limited: Modular Assembly 1200x600x700 Intellectual Property Rights May Apply Page 6 of 6
April 2014 www.sikatech.co.nz ST-PD015-01
Chamber Accessories
Cable Support & Protection Options Cable Protection Plate
Cable Management Bracket
Cable Stirrup Bracket
Option 145 mm Long
Option 250 mm Long
‘J’ Brackets