Silver Cross Elegance User manual

Elegance
Sleigh Cot bed
IMPORTANT: THE ASSEMBLY OF THIS
PRODUCT REQUIRES TWO PEOPLE
IMPORTANT, RETAIN FOR FUTURE
REFERENCE: READ CAREFULLY

Baby cot
Day bed
Junior bed

A = 2pcs C = 6pcs D = 6pcs E = 10pcs F = 4pcs
G = 4pcs H = 8pcs I = 1pcs J = 1pcsK = 2pcs L = 2pcs

Drawer
BOTTOM SIDE PANEL

6
Baby cot assembly
C x 6
D x 6
A x 2
E x 6

7
F x 2

8
F x 2

G x 4
H x 8
K x 2
L x 2

10
BOTTOM SIDE PANEL

11
PRESSING EVENLY ON EACH
SIDE OF THE DRAWER, SLIDE
THE DRAWER INTO PLACE
UNTIL CLICKS.

1
2
12
Day bed
E x 2
F x 1

13
3
F x 1

4
4
14
G x 4
PRESSING EVENLY ON EACH SIDE OF
THE DRAWER, SLIDE THE DRAWER
INTO PLACE UNTIL CLICKS.

15
1
Junior bed
E x 2
2
D x 6

3
16

4
17

18
6
5
G x 4

19
WARNINGS & INSTRUCTIONS
FOR SAFE USE & MAINTENANCE
BE AWARE OF THE RISK OF OPEN FIRE AND
OTHER SOURCES OF STRONG HEAT, SUCH AS
ELECTRIC BAR GAS FIRES, ETC. IN THE NEAR
VICINITY OF THE COT.
DO NOT USE THE COT/BED IF ANY PART IS
BROKEN, TORN OR MISSING AND USE ONLY
SPARE PARTS APPROVED BY SILVER CROSS.
DO NOT LEAVE ANYTHING IN THE COT OR
PLACE THE COT NEAR TO ANOTHER PRODUCT,
WHICH COULD PROVIDE A FOOTHOLD OR
PRESENT A DANGER OF SUFFOCATION OR
STRANGULATION, E.G.STRINGS, BLINDS,
CURTAIN CORDS, ETC.
DO NOT USE MORE THAN ONE MATTRESS IN
THE COT.
WHEN CONVERTED INTO CHILD’S BED MODE,
DO NOT PLACE NEAR HEAT SOURCES,
WINDOWS AND OTHER FURNITURE.
THE BED IS DESIGNED TO BE DISMANTLED FOR
STORAGE OR TRANSPORTATION;
ANY ADDITIONAL OR REPLACEMENT PARTS
ARE OBTAINED FROM THE MANUFACTURER OR
DISTRIBUTOR.
ALL PARTS OF THE COT SHOULD BE
TIGHTENED CORRECTLY. CARE SHOULD BE
TAKEN TO ENSURE THAT NONE OF THE
FITTINGS ARE LOOSE OR PROTRUDING AS
THIS COULD TRAP PARTS OF THE BODY OR
CLOTHING, RIBBONS, DRAWSTRINGS,
NECKLACES ETC., AND POSE A RISK OF
STRANGULATION.
THE LOWEST POSITION ON THE COT BASE
SAFEST POSITION. YOU SHOULD USE THE
COT IN THIS POSITION AS SOON AS YOUR
BABY IS OLD ENOUGH TO SIT UP.
THE THICKNESS OF THE MATTRESS SHALL
BE SUCH THAT THE INTERNAL HEIGHT
(SURFACE OF THE MATTRESS TO THE UPPER
EDGE OF THE COT FRAME) IS AT LEAST 500
MM IN THE LOWEST POSITION OF THE COT
BASE AND AT LEAST 200 MM IN THE
HIGHEST POSITION OF THE COT BASE.
THE THICKNESS OF MATTRESS SHALL NOT
EXCEED 100 MM. WE RECOMMEND THE USE
OF A 400 SIZE MATTRESS (1400 X 700 MM).
THE MATTRESS LENGTH AND WIDTH SHALL
BE SUCH THAT THE GAP BETWEEN THE
MATTRESS AND THE SIDES AND ENDS DOES
NOT EXCEED 30 MM.
YOUR COT/BED MAY BE CLEANED WITH A
DAMP CLOTH. NEVER USE ABRASIVES OR
BLEACH.
THOROUGHLY DRY IMMEDIATELY AFTER
CLEANING.

20
WARNINGS & INSTRUCTIONS
FOR SAFE USE & MAINTENANCE
ALL ASSEMBLY FITTINGS SHOULD ALWAYS BE
TIGHTENED PROPERTY AND ALL FITTINGS
SHOULD BE CHECKED REGULARLY AND
RE-TIGHTENED AS NECESSARY.
TO PREVENT INJURIES FROM FALLS, WHEN A
CHILD IS ABLE TO CLIMB OUT OF THE COT, IT
SHOULD NO LONGER BE USED FOR THAT
CHILD.
THIS COT BED IS INTENDED FOR CHILDREN
AGED FROM BIRTH TO 4 YEARS
APPROXIMATELY. WHEN CONVERTED INTO A
COT BED IT CONFORMS TO BS
8509:2008+A1:2011
CHILDREN ARE LIKELY TO PLAY, BOUNCE,
JUMP AND CLIMB ON BEDS, THEREFORE THE
CHILD’S BED SHOULD NOT BE PLACED TOO
CLOSE TO OTHER FURNITURE OR WINDOWS,
BLIND CORDS, CURTAIN PULLS OR OTHER
STRINGS OR CORDS, AND SHOULD BE PLACED
EITHER TIGHT TO ANY WALL OR HAVE A GAP
OF 300 MM BETWEEN THE WALL AND THE SIDE
OF THE BED.