Sim-Lab GT1-PRO User manual

GT1-PRO COCKPIT
VERSION 1.0
Last updated: 12-07-2023
INSTRUCTION MANUAL

2|2 19
BEFORE YOU START:
Thank you for purchasing this Sim-Lab product! On the following pages, you will find detailed instructions
on assembly. This requires only a set of simple tools and some of your time. Please check the bill of
materials before starting (page 18) and make sure all the parts are delivered.
For the angled profiles, the lengths in the bill of materials might not perfectly match the length of the
part you measure. Don’t worry, we measure differently when cutting the profiles and with the angles as
they are, the given dimensions are a close approximation.
We tried to go with a different style of assembly for this one. Don’t panic if you can’t find any
corner brackets included in the hardware bags.
Inserting Slot-Nuts:
You got excited, finished the build, put the caps on, but forgot to install
one element. Do not worry. It happens to everyone. In this diagram, you
can see how to insert a Slot-Nut directly into the slot from the side.
You can also use one of your smaller Hex wrenches to help wiggle
the Slot-Nut in place.
5/6MM
Tools needed:

3|3 19
Note: the counterbores should point (arrows)
to the outside of the cockpit. This page is
showing assembly for the LEFT side.
BUILD 2X
M8 X 20
2X
Slot-Nut M8
2X
A1
1X
Profile 80X40
End-Cap
2X
Rubber
Foot
2X
A1
A28
A18
A17
A25

4|4 19
A4
2X
M8 X 40
8X
Washer M8
(DIN 988)
8X
A4
A27 A21

5|5 19
Slot-Nut M8
4X
A6
2X
Profile 40X40
End-Cap
4X
M8 X 40
4X
Washer M8
(DIN 988)
4X
A6
A21
A27
A28
A20

6|6 19
Part A12 is only countersunk on one
side, therefore only fits on the LEFT
side of the cockpit.
For the RIGHT side of the upright
assembly, see the next page.
BUILD 2X
Profile 80X40
End-Cap Angled
2X
Slot-Nut M8
9X
A2
1X
M8 X 20
4X
Sandwhich Plate
LEFT*
1X
A12
A28
A24
A19
A2

7|7 19
M8 X 20
8X
Slot-Nut M8
8X
Washer M8
8X
A13
A22 A26
A28
A2

8|8 19
BUILD 2X
Slot-Nut M8
4X
A7
1X
Profile 40X40
End-Cap
2X A20
A7
A28

9|9 19
M8 X 16
(A23)
Washer M8
8X
4X
M8 X 20
(A22)
4X
Pedal Deck
Upright Left
1X
Pedal Deck
Upright Right
1X
Pedal Deck
Pivot
2X
Slot-Nut M8
4X
A9
A8
A22
A26
A10
A28
A23

10 |10 19
M8 X 16
(A23)
Washer M8
4X
2X
M8 X 20
(A22)
2X
A22 A26
A23

11 |11 19
M8 X 16 Washer M8
4X
4X
Pedal Deck
1X
A11
A23
A26

12 |12 19
Washer M8
6X
M8 X 20
6X
Wheel Deck
1X
A14
A26
A22

13 |13 19
Part A15 is symmetrical and can be
used on both sides of the cockpit.
Profile 80X40
End-Cap Angled
2X
Slot-Nut M8
4X
A5
1X
M8 X 20
4X
Side Mount
Sandwhich Plate
1X
A15
A28
A24
A19
A5

14 |14 19
Slot-Nut M8
4X
A3
1X
M8 X 16
4X
Side Mount
Plate
2X
Washer M8
4X
A3
A16
A28
A26
A23

15 |15 19
Washer M8
4X
M8 X 20
4X
Slot-Nut M8
4X
A22
A26
A28

16 |16 19
Washer M8
4X
M8 X 16
4X
Slot-Nut M8
4X
A23
A26
A28

17 |17 19
Washer M8
8X
M8 X 25
4X
Lock-Nut M8
4X
Servo Mount
Left
1X
Servo Mount
Right
1X
B1
B2
B4
B6
B5

18 |18 19
BOX A - GT1-Pro
PROFILE KIT
#Part QTY Note
A1 80X40 Length=1350mm 2 Machined.
A2 80X40 Length=750mm 2 Angled, with logo.
A3 80X40 Length=560mm 1 Angled.
A4 80X40 Length=500mm 2
A5 80X40 Length=430mm 1 Angled.
A6 40X40 Length=500mm 2 Machined.
A7 40X40 Length=400mm 2
HARDWARE KIT
A8 Pedal deck upright left 1
A9 Pedal deck upright right 1
A10 Pedal deck pivot 2
A11 Pedal deck 1
A12 Sandwich plate left 1
A13 Sandwich plate right 1
A14 Wheel deck 1
A15 Side mount sandwich plate 1
A16 Side mount plate 2
A17 Rubber foot 4
A18 Profile 80x40 end-cap 4
A19 Profile 80x40 end-cap angled 6
A20 Profile 40x40 end-cap 8
#Part QTY Note
A21 Bolt M8 X 40 DIN 912 12
A22 Bolt M8 X 20 DIN 912 24
A23 Bolt M8 X 16 DIN 912 18
A24 Bolt M8 X 20 DIN 7991 12 Countersunk.
A25 Bolt M8 X 20 DIN 7380-2 4
A26 Washer M8 DIN 125-A 42
A27 Washer M8 DIN 988 12
A28 Slot-Nut M8 62
BOX B - GT1-Pro Servo Mount
HARDWARE KIT
#Part QTY Note
B1 Servo mount left 1
B2 Servo mount right 1
B3 Bolt M8 X 40 DIN 912 4
B4 Bolt M8 X 25 DIN 912 4
B5 Washer M8 DIN 125-A 16
B6 Lock-Nut M8 8
Disclaimer: for some entries on this page, we supply more than required as spare
materials. Don’t worry if you have some leftovers, this is intentional.

19 |19 19
If you still have some questions regarding assembly of this product or about the manual itself,
please refer to our support department. They can be reached at
suppor[email protected]
Alternatively, we now have a Discord server where there are quite some experienced Sim-Lab
customers hanging out. They might just help you along if you ask them nicely ;)
www.sim-lab.eu/discord
If you feel like printing this manual, please consider the environment before doing so. For the best
results, make sure you print at 100% scale without borders.
Product page on the Sim-Lab website: