Simons Voss Technologies 3067 User manual

Programming Transponder 3067
State of: June 2006

Programming Transponder 3067
Content
1.0 Introduction _________________________________________3
2.0 Backup Card _________________________________________3
3.0 Programming Notes___________________________________4
3.1 Error Messages__________________________________________ 4
3.2 Initial Programming ______________________________________ 4
3.3 Reading Out a Transponder _______________________________ 5
3.4 Adding a New Transponder ________________________________ 5
3.5 Emergency Opening ______________________________________ 6
3.6 Blocking a Lost Transponder ______________________________ 6
4.0 Loss of the Programming Transponder___________________7
5.0 Data Sheet___________________________________________7

Programming Transponder 3067
Page 3
1.0 Introduction
The Programming Transponder 3067 is used for programming Digital Locking
Cylinder 3061 and Transponder 3064 devices. You can use it to perform the following
actions:
zProgram the system for the first time
zMake changes to the authorisations
zBlock lost transponders
zDetermine the ID number of a transponder
It is not possible to read out the locking cylinder with the Programming Transponder.
Each transponder receives its own ID number and secret password when the system
is programmed for the first time. This allows the locking cylinders to distinguish
between the different transponders.
The Programming Transponder takes care of this job. It assigns a consecutive ID
number to the transponders, beginning with 1. The next transponder receives the
number 2, and so on. You can program a maximum of 99 transponders and a
maximum of 250 lockings with a program transponder.
While the Programming Transponder is carrying out the programming, the locking
cylinders are also learning the secret password, as well as which transponders will be
authorised in the future.
2.0 Backup Card
The entire system is protected by a secret password that is saved at the factory on
the Programmer Transponder 3067. The system password is stored on the backup
card. The password is covered by a scratch panel and does not have to be scratched
free for programming. Keep this backup card in a safe place and make sure it is not
accessible to third parties. If the backup card is lost, it may be necessary to replace
the entire locking system.

Programming Transponder 3067
Page 4
3.0 Programming Notes
Always position only one locking cylinder in the immediate vicinity of the
Programming Transponder during programming. All other components must be at a
distance of at least 1 m (3.3 feet).
3.1 Error Messages
If you receive one of the following signals when not expected during the
programming, there has been an error.
zLight emitting diode (LED) blinks red 1x:
Action: Correct the distance to the cylinder or transponder and try again.
zLED flickers and then blinks red 2x.
You have tried to authorise a transponder in more than 3 different locking
systems. (A transponder can be authorised for a maximum of 3 different
locking systems).
zLED flickers and then blinks red 3x:
You have tried to program more than the maximum allowable number of
transponders or cylinders.
zLED flickers and then blinks red 4x.
You have tried to authorise a transponder for a cylinder that does not
belong to your locking system.
or
The programming transponder button was pressed too long.
3.2 Initial Programming
The following programming steps must be done very quickly, because otherwise
the Programming Transponder automatically shuts down, which interrupts the
programming.
Be absolutely sure to maintain a minimum distance of 1 meter (3.3 feet) from the
locking cylinder to the Programming Transponder when carrying out steps 1 and 2.
1. Briefly press the Programming Transponder button once. The light emitting
diode then blinks green.
2. Operate the transponder that you want to program at a distance of from
approximately 10 to 20 cm (4 to 8 in.) to the Programming Transponder and
wait until the light emitting diode on the Programming Transponder lights
green for three seconds. If you want to authorise another transponder, repeat
step 2.
3. Once you have authorised all transponders, hold the Programming
Transponder near the inner knob of the cylinder (long knob) and briefly press

Programming Transponder 3067
Page 5
its
button one time. Attention: you must press the button during the LED’s
blinking phase. The data is then transferred. The locking cylinder makes
several signal tones during this part of the programming. If the programming
was successful, the cylinder couples and the LED on the Programming
Transponder lights green.
4. Perform a test to see whether all of the transponders that you have
programmed function perfectly.
5. Follow the same procedure to program additional locking cylinders.
3.3 Reading Out a Transponder
In order to be able to block a lost transponder for a specific locking cylinder, you need
its ID number. We recommend that you create a list containing the name of the owner
and the accompanying ID number of the transponder. You can determine this with the
Programming Transponder:
1. Briefly operate the Programming Transponder until it blinks green.
2. Hold the transponder whose ID number you want to read out near the
Programming Transponder. Briefly operate the transponder. The LED on the
Programming Transponder lights green for approximately 3 seconds.
3. Press the transponder button again. The LED lights yellowish for
approximately 2 seconds.
4. The ID number of the transponder is shown by the different coloured blinking
of the LED.
Red blinking indicates the tens and green blinking indicates the ones.
Example: If the ID number of the transponder is 25, the LED blinks red 2x and
then green 5x. If the ID number has only one digit, only the green LED blinks.
5. Once the ID number has been determined, the LED on the Programming
Transponder lights yellowish again.
3.4 Adding a New Transponder
If you want to authorise a new transponder, proceed in the same way as for the initial
programming. You do not have to repeat the procedure for reading in transponders
that were already authorised for locking.

Programming Transponder 3067
Page 6
3.5 Emergency Opening
It is possible to perform an emergency opening with the Programming Transponder.
Proceed as follows:
1. Press the Programming Transponder button briefly one time. Then the LED
blinks green.
2. Hold the Programming Transponder at a distance of approximately 10 to
20 cm (approximately 4 to 8 inches) from the locking cylinder and briefly press
the button.
Attention: you must press the button during the LED’s blinking phase.
3.6 Blocking a Lost Transponder
The procedure depends on whether or not you know the ID number of the lost
transponder. If you do not know it, proceed as follows:
1. Press the Programming Transponder button until the light emitting diode
blinks red.
2. Hold the Programming Transponder near the inner knob of the cylinder (long
knob) until the LED lights green for approximately 3 seconds and the cylinder
couples.
3. You have now deleted all authorised transponders and must reprogram then
as described in Chapter 3.2.
If you know the ID number, you can block this specific transponder with the following
steps:
Note: It is important that the steps be executed quickly for this procedure, too.
Memorise the ID number of the transponder so that you can enter it immediately in
the
following steps. Like when reading out the number, the input is done in tens (red) and
ones (green).
1. Press the Programming Transponder button until the light emitting diode
blinks red. Then release the button.
2. Then repeat the procedure and wait until the LED lights red. Immediately (red
LED must still be lit) press the Programming Transponder button the
appropriate number of times to enter the number of tens (only if there are
more than nine transponders).
3. The LED now begins to light green. Now enter the number of ones in the
same way (now the green LED must still be lit).

Programming Transponder 3067
Page 7
4. The Programming Transponder repeats the ID number that you enter as a
check. First the LED briefly lights yellowish. Then the Programming
Transponder outputs the ID number with red and green blinking. The color
then changes back to yellow and finally the LED blinks green.
5. If the displayed number is correct, hold the Programming Transponder near
the inner knob of the cylinder (long knob) and press its button.
6. Then the data transfer takes place (signal tones on the cylinder). Wait until the
LED has lit green for 3 seconds and the cylinder has coupled. The data
transfer is not completed until this happens.
4.0 Loss of the Programming Transponder
Get your backup card and contact your dealer. You will receive a new Programming
Transponder, which you first must reauthorize for your cylinders.
To do this, proceed as follows:
1. Hold your new Programming Transponder in front of a cylinder and press its
button twice. The LED lights green for approximately 3 seconds and the
cylinder couples.
2. Then hold your new Programming Transponder in front of the same cylinder,
but this time press its button only once.
3. The light emitting diode blinks yellowish and goes out. The cylinder couples
and the LED lights green for approximately 3 seconds.
4. Repeat steps 2 and 3 for all other cylinders in your locking system.
5. Once you have authorised the new Programming Transponder on all
cylinders, press its button until the LED stops blinking.
6. The new Programming Transponder is now ready to use.
5.0 Data Sheet
Housing Material Plastic
Colour Grey
Dimensions 58 x 38 x 12.3 mm