Simpson QUIK DRIVE QDBDT75 User manual

OPERATING INSTRUCTIONS
© C2009 SIMPSON STRONG-TIE COMPANY, INC. T-QDBDT75INAU09
www.strongtie.com/products/quikdrive_au
READ BEFORE SAVE THESE
OPERATING INSTRUCTIONS
QUIK DRIVE®QDBDT75
GENERAL SAFETY RULES
Always read and understand the tool’s operator’s manual, tool•
marking and the instruction package before starting any work.
Stay alert, watch what you are doing and use common sense when•
using this tool.
Keep your work area clean and well lit.•
Keep bystanders, children and visitors away when using this tool.•
Do not use tool when you are tired or under the influence of drugs,•
alcohol or medication.
Always wear eye protection when operating or servicing the tool.•
When servicing the tool, use only identical replacement parts.•
Follow instructions regarding maintenance in the tool operator•
manual.
Maintain labels and nameplates. If unreadable or missing, contact•
the manufacturer for a replacement.
SPECIFIC SAFETY RULES
While assembling system components, screwdriver motor should•
be unplugged from power source.
Keep hands, feet and head away from the tip (screw outlet) of the•
tool.
Tool can eject screw without being connected to motor or power•
source.
Do not cycle attachment while pointed at any body part.•
If a screw should become jammed in the auto-feed attachment,•
immediately disengage the power source and point the tool in a safe
direction.
Flying Objects.
Wear approved
eye protection
when operating
this equipment
Rotating parts.
Loose clothes, jewelry
or long hair can be
caught in moving
parts
Sharp Objects.
Sharp objects can
puncture hand
and fingers
DRIVING SCREWS
Be sure screwdriver motor is
in FORWARD.
Start screwdriver motor
before applying pressure.
Apply pressure to keep bit
engaged until screw is fully
driven and clutch releases.
Keep screwdriver motor
running between screws.
QUICK START INSTRUCTIONS Complete instructions inside Screwdriver motor sold separately
Use with or without
the “Stand-up”
Extension
1.
2.
4.
3.

PARTS and COMPONENTS
PROBLEM SOLUTION
Screws won’t drive.
They spin for a second, then lay over
on their side. Little or no penetration.
Make sure the screwdriver motor is NOT in reverse.
Screws won’t drive completely.
They go down about halfway, then
the bit spins out.
Check to be sure you are using the correct bit for the type of screws you are driving.
Check for bit wear. It may be time to install a new bit.
Push harder when driving.
Screws won’t drive completely.
They are almost completely driven
but won’t seat completely.
Check the depth adjustment on the attachment. Reset if necessary.
You may have missed the substrate.
Ensure pressure is being applied during screw installation until clutch on
screwdriver motor disengages.
Screws don’t advance properly
causing tool to jam.
Use only genuine Quik Drive brand collated screws.
Lift tool completely off the work surface after driving each screw.
Technical Support Australia 02 9831 7700
Using the correct driving bit is necessary.
Variations in materials and driving technique can cause excessive wear so additional bit packs are available for purchase.
BIT PACK PRODUCT CODES (Mandrel, washer and retaining ring not included):
Replacement Bits: BITHEXLB14• - 1/4” Hex Drive | BITHEXLB516 - 5/16” Hex Drive | BITHEXLB38 - 3/8” Hex Drive
Replacement Mandrel Set: BPHXBDT• - 5/16” Hex Drive includes removable bit, mandrel, washer and retaining ring
TROUBLESHOOTING GUIDE
ATTACHMENT EXTENSION SCREWDRIVER MOTOR
BPHXBDT MANDREL found inside attachment
FASTENER RELEASE BUTTON PROFILE GUIDE CLAMP SCREW
DEPTH ADJUSTMENT KNOB HANDLE TO BE USED
WITHOUT EXTENSION
INTERCHANGEABLE
PROFILE GUIDES
PBDT75PG11
Flat/Cladding Profile
PBDT75PG21
Corrugated Profile
PBDT75PG31
Square Ridge Profile
INTERCHANGEABLE
PROFILE GUIDE SHAFT factory installed, inside extension

OPERATING INSTRUCTIONS
ATTACH ADAPTOR TO YOUR SCREWDRIVER MOTOR
(Motor sold separately)
Unplug the screwdriver motor and remove nose-cone and bit
holder from your screwdriver motor according to manufacturer’s
directions (most will pull straight off).
Replace with Quik Drive adaptor made for the screwdriver motor.
Follow specific instructions included with Quik Drive adaptor.
ATTACH EXTENSION TO SCREWDRIVER MOTOR
Turn the clamping handle in the “off” direction
(clockwise) until the internal clamp is out of the way.
Insert the screwdriver motor, with G2 Adaptor in place, into
the end of the extension. Push tight and tighten clamping
handle. If it won’t fully insert, rotate the extension until
the teeth mesh.
SET DEPTH
Turn dial to adjust depth and
tighten lock ring to set. Test in
scrap material before use.
ADJUST HANDLE HEIGHT
Internal
Clamp
Hex end of
extension
drive shaft
Turn thumbscrew
clockwise to
open clamp
CHANGING THE HEX MANDREL
The mandrel must be removed
from the front nose. To remove,
pry off retaining clip and washer,
slide mandrel out through
opposite end. Reverse steps to
install. (Install washer followed
by retaining clip)
Seat mandrel
first, then add
attachment
If new tool is hard
to lock on, place
nose on solid
surface and push
down
Check locking lever position to be sure
attachment is locked on
To remove, unlock and pull
CONNECT ATTACHMENT TO
SCREWDRIVER MOTOR OR EXTENSION
Insert mandrel into extension, slide
attachment on and push tight - until the
locking lever snaps in place.
You can turn the attachment any way that
is comfortable.
New tools may be tight and hard to lock in
place. If so, ensure there are NO screws
loaded in the attachment and put the nose
against a solid surface and push down
sharply (see photo at far right).
NOT locked on
Flush
with side
of tool
Flush
with top
of tool
Increase
Depth Lock Ring
Depress
release
button and
pull screw
belt out
Depress
at top to
release
Locked on
LOAD and REMOVE SCREWS
Insert the belt into the belt-guide up to 1 position
ahead of the first screwing position. If the belt is
inserted too far, press release button on head of
tool and pull belt out of the tool an insert again.
One position
ahead of
first screw

OPERATING INSTRUCTIONS
Australia 02 9831 7700 www.strongtie.com/products/quikdrive_au
MAINTENANCE
As a regular maintenance procedure for the attachment, we recommend that regular cleaning of the attachment be
performed. Normally, blowing a high pressure stream of air on and in the attachment should be sufficient.
CHANGING PROFILE GUIDE and
ADJUSTING DEPTH STOP
To change profile guide, remove
clamp screw, insert desired guide,
replace and tighten clamp screw.
Proper adjustment of profile guide
is necessary depending on screw
size - loosen clamp screw and
position guide 2-3mm in front of
the screw point.
CLEARING JAMMED SCREWS
If a screw should become jammed in the auto-feed attachment, disengage the
power source and point the tool in a safe direction. Remove jammed screw. If
needed, depress fastener release button, firmly grasp the screw belt and pull it
out of feed track. See troubleshooting guide if problem persists.
Loosen/Tighten
Clamp Screw to adjust
Slide profile
guide out to
replace
Adjust
guide
2-3mm
in front
of screw
point.
Screws
may
become
jammed