Sinclair AMC-09C User manual

USER'S MANUAL
AMC-09C
MOBILE SERIES

...............................................
1
....................................... .
..................................... .
..............................................
............................................
22
...........................................
.........................................
24
23
25
2
1
3
..................................
..................................
..................................
.................................. .
.................................
17-19
20-21
.........................................
11
13
14
15
16
.................
4-8
9-10
...............
CONTENTS
Summary
Working principle
Models & specifications
Structure
Operating methods
Names and Functions of the Remote Controller
COOL mode operation
DRY mode operation
SLEEP mode operation
AUTO mode operation
TIMER mode operation
Installation guide for castor, drainage pipe and air exhaust accessory
Care and Maintenance
Trouble shooting
User notices
After service
Circuit diagram
...................................
.........
.....................................

－2－
SUMMARY
－1－
This MOBILE AIR CONDITIONER is a small, moveable air conditioner. It possessed the
functions of COOL, HEAT, DRY and the Separate Ventilation, and depends on different places, it
canbemovedaswill.Itisfitforhome andofficeuse,especiallyfitforthehousewithmanyrooms.
Withthecompactconfiguration,excellentworkmanship,elegantappearance,itlookslikeastanding
Benzcar. Itisconvenientformoving,energysaving,andwith lownoise.
Note:Pleasereadthismanualcarefullybeforeoperatingtheunit,themanualisusedforreference,
andthetechnicalparameters aresubjecttochangewithoutnotice.
WORKING PRINCIPLE
With the help of upper motor, the airflow of indoor pass through the evaporator becomes the
cooled wind, but with the help of lower motor, the airflow of indoor pass through the condenser
becomes the heated wind. There is two duct systems designed in its structure.The heated wind is discharged
bytherearoutlet,thecooled windisdischargedbythefrontoutlet,flow-guidedbythelouver,andit
brings the gentle cooling airflow, and the low temperature environment is maintained.
The Working Principle
Cooled wind
Upper
motor
Lower
motor
Evaporator
Airflow 1
Airflow 2
Capillary
Heated wind
Condenser

－2－
MODELS AND SPECIFICATIONS
Note:
1.The noisewastestedwhentheunitisrunningincooling windmode,1meterawayfromthefront
outlet, dehumidifying capacity.
2.The technical parameters are subject to be changedwithout notice. Please refer to those listed on
Model AMC-09C
Cooling Capacity(W) 2600W
Power Source 220－240V ～50Hz
Rated Input Current(A) 5.3
Rated Power Input(W) 1200
Flow Volume(m3/h) 430
Sound Press Level dB(A) 55
Refrigerant R407C
Net Weight（Kg）31
Dimension(Body)(H×W
×D）（mm）840×450×370
Dimension(Package)(H×
W×D）（mm）880×685×425
nameplate of the unit.
3. Device is not intended for continuous running

－3－
STRUCTURE
Control panel
Air outlet
Handle
Lower air inlet
Front
Rear
Upper air inlet grille
Power cable
Air exhaust outlet
Lower air inlet grille

OPERATING METHODS
５
０ｃ
ｍ
５０ｃｍ
－4－
The working range of COOL mode is 16℃-35℃, the working range of
DRYmode is 16℃-35℃．
When operating, the unit should be placed on the horizontal place and
more than 50cm away from the wall or other obstructions.
The working range of COOL
mode and DRYmode
Location conditions
Power supply Before the unit is power-on, please check the following:
The power supply voltage 6%.
● The lead wire is suitable for the start-up current of more than 20A,
to avoid the voltage decline when the unit starts suddenly.
● The power plugs and the sockets can be supported by the current
that is more than 16A.
● The thread section of the lead wires and any continued use lead wire
is no less than 2.5mm2.
● If the power supply cord is damaged, replace it by the special
power supply cord.
● If the power supply is needed to replace or maintain, please
contact with the dealer and ask for the professional personnel to do
the repairing work.
● The air conditioner must be safety earthed. Earth wire must be
connected to the special device of the building. That is for providing
good earthing for the air conditioner.

OPERATING METHODS
●Can not use steel wire or brass wire to replace fuse, the capability
of fuse must be appropriate. In order to avoid damage to power cord
and electrical leakage, do not fix the power supply on the knife edge or
sharp object.
●The wiring must be operated by the professional and according
to the national regulations. In fixed circuit, there must be electricity
leakage protection switch of enough power capacity and 16A thermal-
magnetic breaker air switch with enough space, the earth wire can't be
connected to water pipe or gas pipe. When the air conditioner is not
used, please pull out the power plug or cut off power supply.
－5－
There must be reliable ground
wire in the power supply
Earthing
Water pipe
Gas pipe

－6－
OPERATING METHODS
LCD instruction (dynamic display)
Names and Functions- Remote Controller
ON/OFF
MODE
FAN SPEED
LCDscreen
SET TEMP.
SET TIMER
SET SLEEP
Remote Control window

－7－
OPERATING METHODS
Controlpanelandthefunction
1. "ON/ OFF "key
Press once to start and press once more to stop the unit.
2."MODE" key
Press this button to change operation mode in order of:
FAN → COOL → DRY →AUTO → FAN
3 "FAN SPEED" key
When the unit is running in "FAN", "COOL" and "HEAT" mode,there are 3 kinds of fan speeds to
be selected, press "FAN SPEED" key to choose between "LOW → MD → HIGH".
4."SET TEMP" key
When turn on the air conditioner, in the "COOL","HEAT" mode, the control panel will display the set
temp. Press "▲"""to increment or to decrement the set temperature.
5. "SET TIMER" key
Press"▲""" key to set the time for timer on or timer off. When the unit is running, you could set the
timer off, the unit will stop running; When the unit is stop running (not power off ), set timer on, andthe
time interval that being set will be 0.5-24 hour(s), press "▲""" key to adjust.
6. "SET SLEEP" key
When the unit is running, press once to set "SLEEP" operation, repress it, the unit will stop the "SLEEP"
operation.There is no "SLEEP" operation in "AUTO" mode.

－8－
OPERATING METHODS
1). Select a place thatnear door and window, install the exhaust duct (the installation
method please refer to P19), put the exhaust duct out of the door, do not close the door
and window tightly, leaveenough space for air flow, for example,open the window or
door to keep agood ventilation.
2). Press "MODE" key to select "COOL" mode.
3). Press "TEMP" key to set the suitable temp.16℃-30℃.
4). Press "FAN" key to select the suitable fan speed, (HIGH, MD, LOW).
When the unit is running in COOL mode, in order to keep agood cooling effect,
please pay more attention to:
１）． If there is the direct sunlight at the window, please use the curtain to shield .
２）． Do not use other heat sources in the air conditioning room.
Please close the door and window to obtain abetter dehumidifying effect:
Press"MODE"key,select"DRY"mode,theunitwillruninthe"DRY"mode,atthe
same time, the upper motor is running at the low speed, it is not adjustable.
When the air conditioner is used as dehumidifier, it is no need to install the exhaust duct.
1). Press "MODE" key, to select "FAN" mode.
2). Press "FAN SPEED" key to choose from the HIGH, MD, LOW fan speed options.
Press "MODE" key to select "AUTO" mode, the microcomputer process will
automatically choose COOL, DRY, HEAT mode, for ensuring the indoor constant
temperature efficiency.
Press"MODE"keytochoose"HEAT"mode,atthesametime,compressorandlower
motor stop running, only PTC is running, the upper motor is running at the set fan speed.
COOL mode
CAUTION
DRY mode
CAUTION
FAN mode
AUTO mode
HEATmode
When in cooling or dehumidifying mode, the dew water will be drained into the tank.
When the tank gets full, the indicator will flash, and the buzzer will sound eight times,
LCD window shows error code “H8”，at the same time the unit stops running.
WATER
Cut off power supply, move the appliance to a suitable place to pull out the plug and
pour out the water in tank. When water is drained out completely, re-insert the plug
back into the drainage pipe to avoid dew water leakage. (As figurre shown below Fig 1) When
restarting the appliance,it must be set again.
METHOD OF
DRAINAGE
If the appliance is placed in a position admitting to drain water, you also can connect the
drain hose to the drain port to drain water.
DRAINAGE
Drainage Pipe Rubber Plug
Fig 1
Fig 2Fig 3
(As figurre shown below Fig 2--Fig 3)
(61OF~86ＯF).

－9－
NAMES AND FUNCTIONS OF THE REMOTE CONTROLLER
LCD screen
It shows all set contents
ON/OFF
HIGH
TIME
AM
MODE
FAN
TIMER
DRY
Hr
SLEEP
Min
SLEEP key
Press this key to set SLEEP operation,
and press the "Hr" key to adjust the time
of timer off (it can be choose from 1-7
h o u r s ) , w h e n r e p r e s s t h i s k e y , t h e
operation will stop.
ON/OFF key
Press once to start and press once more
to stop the unit.
DRY key
SEND key
Press this key to transmit the operation,
thescreen will show the operation.
Pressthiskey,theairconditionerwill run
in DRYmode.
●Makesuretoaimthesignalportofremote
controller at the signal receiver indicator of front
panel.
Onlythe AUTO,ON/OFF,SLEEP,SEND keys
could beusedtosendthecurrentdisplayoperation,
the other keys could be used to change the mode.
The other functions please refer to the cooling
only type air conditioner
SEND
NOTE: When using Fahrenheit remote controller
the sign 'Oc', '+Oc'or '-Oc' will be corresponding
changed to 'OF','+OF' or '-OF'.

－10－
●In case of the power off during the operation, all options will be
ceased.
●If need to resume the operation, please repress the "SEND" key. If
thereismalfunctionintheoperationprocedure,orwrongoperation
due to the thunder,pleasepulloutthepowerplug,and reinsert it,
then press the "SEND" key.
POWER OFF
HIGH
TIME
AM
MODE
FAN
SEND
TIMER
DRY
Hr
SLEEP
Min
NAMES AND FUNCTIONS OF THE REMOTE CONTROLLER
MODE key
Press the "MODE" key step by step, the
LCD will display the COOL-FAN-HEAT-
AUTO mode, circularly.
TEMP key
Press once, the SET TEMP. will decrease
1℃. Press once, the SET TEMP. will
increase 1℃. The SET TEMP. can be
selectedfrom16℃-30℃
FAN key
The switchover of FAN mode are HIGH-
MD-LOW.
TIMER key
Press the key to select the SET TIMER mode or
theTIMEmode.Whenselectthe"SETTIMER"
mode, the LCD will display the time of the SET
TIMER mode, while select the "TIME" mode,
the LCD will display the current time.
Hr/Min key
When the unit is running in the "TIME" mode,
press "Hr" once, the number will increase 1,
press "Min" once, the number will increase 1.
When the unit is running in the "SET TIMER"
mode, press the key once between 0-7, the
number of time will increase 0.5, press the key
once above 8, the number of time will increase
1. When the unit is running in "SLEEP" mode,
press the "Hr" key once, the time interval will
increase 1 hour, and will circulate from 1 to 7
hour(s).
ON/OFF
NOTE: When using Fahrenheit remote controller
the sign 'Oc', '+Oc'or '-Oc'will be corresponding
changed to 'OF','+OF' or '-OF'.
(61OF~86ＯF).

－11－
COOLMODE OPERATION
COOL
●When temperature of room sensor is higher
than the set temp, compressor runs, the unit starts
cooling operation.
●When temperature of room sensor is lower
than the set temp, compressor stops, the unit runs
in "FAN" mode.
●The set temp should be in range of 16℃~30℃.
HIGH
TIME
AM
MODE
FAN
SEND
TIMER
DRY
Hr
SLEEP
Min
１８ Ｃ
０
1.After inserting the batteries, press
"ON/OFF" key to start the unit.
2. Press "MODE" key, to choose "COOL"
mode.
3. Press "FAN" key, to set fan speed.
4. Press "TEMP" key, to set the desired
temp.
5. Press "SEND" key, send the operation
to the unit.
ON/OFF
NOTE: When using Fahrenheit remote controller
the sign 'Oc', '+Oc'or '-Oc'will be corresponding
changedto 'OF','+OF' or '-OF'.
(61OF~86ＯF).

－13－
DRY MODE OPERATION
When the unit is in DRY mode, the compressor
is protected, the fan motor runs at low fan speed.
DRY
HIGH
TIME
AM
MODE
FAN
SEND
TIMER
DRY
Hr
SLEEP
Min
１８ Ｃ
０
5.Press "SEND" key to transmit the
operationto the unit.
1.After inserting the batteries, press
"ON/OFF" key to start the unit.
2.Press "DRY" key, to set "DRY" mode,
when repress the key, it will run in original
operation.
3.Press "TEMP" key, to set desired temp.
4.Press "FAN" key, to set fan speed.
ON/OFF
NOTE: When using Fahrenheit remote controller
the sign 'Oc', '+Oc'or '-Oc'will be corresponding
changedto 'OF','+OF' or '-OF'.

－14－
SLEEP MODE OPERATION
● When the unit is running in SLEEP mode, press "Hr"
key to set timer on, the interval is 1-7 hours.
● When the unit is running in SLEEP mode, according to
the time changes, it could adjust the original set temp
automatically to save energy and make a comfortable
sleeping.
1. After inserting the batteries, press
"ON/OFF" key to start the unit.
2. Press "MODE" key, to select the
operation mode.
3. Press "TEMP" key, to set desired
temp.
4. Press "FAN" key to set fan speed.
5. Press "SEND" keyto transmit the
operation to the unit.
6. Press "SLEEP" key, to set SLEEP
operation, when press once more it
will stop.
HIGH
TIME
AM
MODE
FAN
SEND
TIMER
DRY
Hr
SLEEP
Min
１８ Ｃ
０
ＳＬＥＥＰ
ON/OFF
NOTE: When using Fahrenheit remote controller
the sign 'Oc', '+Oc'or '-Oc' will be corresponding
changeed to 'OF','+OF' or '-OF'.

－15－
AUTO MODE OPERATION
● According to the room temp, the microcomputer will
adjusttheturnonorturnoffofthecompressorautomatically
to offer comfortable effect.
AUTO MODE
HIGH
TIMER
MODE
FAN
SEND
TIMER
DRY
Hr
SLEEP
Min
1. After inserting the batteries, press
"ON/OFF" key to start the unit.
2. Press "MODE" key, select "AUTO"
mode, according to the room temp, the
microcomputer will adjust the turn on
or turn off of the compressor and fan
motorautomaticallyto offer comfortable
effect.
3. Press "SEND" keyto transmit the
operation to the unit.
ON/OFF
NOTE: When using Fahrenheit remote controller
the sign 'Oc', '+Oc'or '-Oc' will be corresponding
changedto 'OF','+OF' or '-OF'.

－16－
TIMER MODE OPERATION
1. When the unit is running, press "TIMER"
key, to set the TIMER operation.
2. Press "Hr/Min" key, to set the TIMER
ON, it can be selected in the range of
1-18 hours.
3. Press "SEND" keyto transmit the
operation to the unit.
keytosettheTIMEROFF,itcouldbe
selected in the range of 1-7 hours.
4. Press "SLEEP" key, then press the "Hr/Min"
●After the SET TIMER ON, the unit turns off at once, when the set
time arrived, the unit will run in original mode.
●Press "TIMER" key, to select "TIME", the screen will display the
current time, press "Hr/Min" key to adjust the number of current hour or
minute.
●When pressing the "SLEEP" key to set the "SLEEP" mode, the "SET
TIMER" mode will be canceled, when selecting the "SET TIMER"
mode, the "SET SLEEP" mode will be canceled.
HIGH
TIMER
MODE
FAN
SEND
TIMER
DRY
Hr
SLEEP
Min
ON/OFF
NOTE: When using Fahrenheit remote controller
the sign 'Oc', '+Oc'or '-Oc' will be corresponding
changedto 'OF','+OF' or '-OF'.

－17－
INSTALLATIONGUIDEFORCASTOR,DRAINAGEPIPEANDAIREXHAUSTACCESSORY
THE AIR EXHAUST
DUCT MOUNTING
METHOD
1.Install the adjutable window silder kit or drill a hole at the
nearest window.
2.Fix the square end of the exhaust duct to the exhaust terminal
of the unit as depicted in Fig 4.
3.Put the other end (discharge) to the window as depicted in
Fig 5 or Fig 6.
Attention:
The length of the air exhaust must be between 500mm--
2000mm.
Plastic Pipe End
Middle Plastic Pipe End
Rear Clip B
Fig 4
Front Plastic Pipe End
Pipe ( 131)
Ø

－18－
INSTALLATION GUIDE FOR CASTOR, DRAINAGE PIPE AND AIR EXHAUST ACCESSORY
CAUTION 1.In order to correctly installing the air exhaust duct please
contact your local dealer for the service.
2.When mounting, try to keep the square end of the exhaust
duct horizonal.
3.Don't add or connect other pipes to it, otherwise it will cause
mechanical malfunction.
Window kit
Rear Clip B
Window
Plastic Pipe End
Hole( 132mm)
Window Or wall
Fig 5
Fig 6
Ø