Sinclair AMC-14Aa MOBILE SERIES User manual

USER'S MANUAL
AMC-14Aa
MOBILE SERIES

CONTENT
1. SUMMARY ．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．1
※．USAGE NOTICE ．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．． 5 -- 7
8. ACCESSORIES AND INSTALLATION OF DRAINAGE HOSE ．． 19--21
※．FUNCTIONS OF DISPLAYER AND PANEL ．．．．．．．．．．．．．．．． 8--1 0
3. SAFETY LABELS OF THE UNIT．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．2
2. WORKING PRINCIPLE．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．1
9. ACCESSORIES OF DRAINAGE WATER ．．．．．．．．．．．．．．．．． . . .. . . 22
4. SPECIFICATIONS ．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．3
5. STRUCTURE．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．4
6. OPERATING METHODS ．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．． 5 --10
7. NAMES AND FUNCTIONS OF THE REMOTE CONTROLLER．．11-- 18 2
10. CARE AND MAINTENANCE ．．．．．．．．．．．．．．．．．．．．．．．．．23 --24
11. TROUBLESHOOTING．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．25
12. USER NOTICES ．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．26 -- 27
13. AFTER SALES SERVICE．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．27

－2－
SUMMARY
－1－
This MOBILE AIR CONDITIONER is a small, movable air conditioner. It possessed the
functions of COOL, HEAT, DRY and the Separate Ventilation, and depends on different places, it
canbemovedaswill.Itisfitforhome andofficeuse,especiallyfitforthehousewithmanyrooms.
Withthecompactconfiguration,excellentworkmanship,elegantappearance,itlookslikeastanding
Benzcar. Itisconvenientformoving,energysaving,andwith lownoise.
Note:Pleasereadthismanualcarefullybeforeoperatingtheunit,themanualisusedforreference,
andthetechnicalparameters aresubjecttochangewithoutnotice.
WORKING PRINCIPLE
With the help of upper motor, the airflow of indoor pass through the evaporator becomes the
cooled wind, but with the help of lower motor, the airflow of indoor pass through the condenser
becomes the heated wind. There is two duct systems designed in its structure.The heated wind is discharged
bytherearoutlet,thecooled windisdischargedbythefrontoutlet,flow-guidedbythelouver,andit
brings the gentle cooling airflow, and the low temperature environment is maintained.
The Working Principle
Cooled wind
Uppermotor
Lowermotor
Evaporator
Airflow 1
Airflow 2
Capillary
Heated wind
Condenser

－2－
You can be killed or seriously injured if
you don't immediately follow instructions.
You can be killed or seriously injured if
you don't follow instructions .
All safety messages will tell you what the potential hazard is, how to reduce the chance of injury, and
what will happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and
obey all safety messages.
This is the safety alert symbol.
This symbol warns you to the potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER"
or "WARNING." These words mean:
SAFETY LABELS OF THE UNIT

－3－
SPECIFICATIONS
Model
Cooling capacity (Btu/h) Rated voltage Rated frequency Cooling rated current (A)
Max. cooling/heating input current (A)
Cooling rated power (W) Max. imput power (W) Airflow (m3/h) Refrigerant and charge amount
Noise (sound press)(cool air outlet)dB(A)
Weight (N.W.) Dimension (H×
W
×
D) (mm)
Package dimension (H×
W
×
D) (mm)
Heating rated power (W)
Heating capacity (W)
14000
220~240V
50Hz
7.4
10.6/--
1700
2450
570
59
840×546×405 870×761×460
47
--
--
A MC-14Aa
4. Noise is tested 1m in front of front air outlet vent under cool air state, it is sound press grade. 5. Please refer performance parameter on nameplate as standard. The design are subject to be 3. Max. input power is tested under cooling mode when indoor temp. dry bulb 35℃and wet bulb 24℃.
Note:
2. Heating capacity is tected when indoor temp. dry bulb 20℃and wet bulb 12℃.
changed without notice.
1. The cooling capacity was tested in the condition of the indoor dry bulb temp.27℃,wet bulb
temp.19℃(the temp of indoor and outdoor are same) with exhaust pipe min length.
R410A 800g
6. Device is not intended for continuous running

－4－
ＳＴＲＵＣＴＵＲＥ
Ｆｒｏｎｔ
Ｒｅａｒ
Control panel
Air outlet
Handle
Upper air inlet grille
Heat air exhaust vent
Power cord
Lower air inlet grille

16℃－30℃．
The working range of COOLｍｏｄｅ ａｎｄ ＤＲＹ ｍｏｄｅ：
Place requirements:
OPERATING METHODS
－5－
※．Usage notice
Unpack the Air Conditioner
Remove packaging materials
Remove and properly dispose the packaging materials. Remove tape and glue residue from surfaces before
WARNING
Excessive Weight Hazard
Use two or more people to move and install the air conditioner.
Failure to do so can result in back or other injury.
turning on the air conditioner. Rub a small amount of liquid dish soap over the adhesive with your fingers.
Wipe with warm water and dry it.
Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue.
These products can damage the surface of your air conditioner.
•
•
•
Place the air conditioner on a smooth level floor that strong enough to support the unit.
Allow at least 12 inches (50 cm) of air space on all sides of the unit for good air ventilation.
Place the unit in an area where the temperature will not fall below 18℃. The coils will be covered
with frost at temperatures below 18℃, and this may reduce performance.
NOTE: The portable air conditioner has wheels for easy movement, but it should only be rolled on smooth and
flat surfaces. Do not attempt to roll the portable air conditioner on carpet or over objects.
12″(50 cm)
min.
12″(50 cm)
min.

Power must adopt the rated voltage and special circuit for AC. And diameter of power cord should be big enough.
OPERATING METHODS
－6－
Electrical Requirements
death, fire, or electrical shock.
WARNING
Electrical Shock Hazard
Plug into a grounded 3-prong outlet.
Failure to follow these instructions can result in
Do not use an extension cord.
Do not use an adapter.
Do not remove ground prong.
The portable air conditioner should be connected to a 230V 50Hz, 15 fused 3 prong grounded outlet.
Time-delay fuse or time-delay circuit breaker is recommended to be used.
All wiring must comply with local and national electrical codes and should be installed by a qualified electrician.
If you have any questions, contact a qualified electrician.
※．Usage notice

－7－
OPERATION METHOD
Earthing
There must be reliable earth
煤
气
管
Water pipe
Gas pipe
※．Usage Notice
■The wiring must be operated by the professional personnel by
protect switch and magnetic and heat drop-off air switch that with
enough capacity in fixed circuit. Don't connect earth wire to water
pipe or gas pipe. When the air conditioner is not used, please pull
out the power plug or cut off power supply.
wire in the power supply
following the national regulation. There must be electric leakage

-8-
OPERATION METHOD
LCD instruction (dynamic display)
Functions for control panel and every button
SLEEP
TIMER TIME
DEHUMIDIFY
Set temp. display Temp. set
display
Fan spedd
Timer On/Off
COOL mode
FAN mode
Auto mode
Power (On/Off)
OPERATION
FAN SPEED
LCD screen
SET TEMP.
SET TIMER
SLEEP
MODE
FUNCTIONS OF DISPLAYER AND PANEL

Turn on or off the unit (press once to turn on, and repress to turn off).
Functions of buttons on control panel:
It can make modes(functions) of this unit change in cycle for user to
select proper function. Function changes on this mode is: Auto→Cool→
3. Fan speed selection button--FAN
LOW→MID→HIGH.
2. MODE
4. Temperature setting button--TEMP
When turning on the unit, under cooling or heating mode, set temp.
value would be displayed on control panel. Press ＋and －to increase
or decrease set temp. value.
Press ＋and －to set timer time to enable the unit turn on and off in set
1. ON/OFF
Dry→Fan
When unit is running in FAN, COOL, or HEAT, there are 3 speeds for
options. Press FAN serially can change fan speed in order of:
5. TIMER
6. SLEEP
time. Timer off time can be set when unit is running, and timer on time
range of 0.5-24 hours, and press ＋and －to adjust.
can be set when unit is off (but not power outage). Timer can be set in
When unit is running, press this button once to begin SLEEP, repress to
quit from SLEEP state. There is no SLEEP state under AUTO mode.
※．Functions of displayer and panel
－9－
OPERATION METHOD
This unit contains memory function. When power outage occur during
operation, the unit stops running. After electrified, the unit would still
operates with the operation mode before power outage.

－10－
When cooling, for improve cooling effect, please note:
①When there is sunshine from window, please draw curtain to shield.
②Try not to use other heat source in the room.
COOLING
AUTO
FAN
1). Press MODE to select COOL mode.
2). Press TEMP to set proper indoor temperature in range of 16℃-30℃.
3). Press FAN to set proper fan speed, HI / MD / LO.
Close windows and doors can get a better dehumidify effect:
Press MODE and select DRY, then unit runs in dehumifidy mode. At this
time, upper fan motor runs in low speed and is unadjustable.
1). Press MODE to select FAN mode.
2). Press FAN to select fan speed at HI, MD and LOW.
When the unit is used as dehumidifier, heat exhaust pipe is unnecessary.
Press MODE to select AUTO, then mode microcomputer would select FAN,
COOL,HEAT and DEHUMIDIFY automatically according to indoor ambient
DEHUMIDIFYING
※．Functions of displayer and panel
OPERATION METHOD
Press MODE to select HEAT. At this time, compressor and lower fan stop
running with only electric heater works. Upper fan runs in set speed.
HEATING
to offer a temperature constanting effect in the room.

－11－
NAMES AND FUNCTIONS OF THE REMOTE CONTROLLER
LCD screen
It shows all set contents
ON/OFF
HIGH
TIME
AM
MODE
FAN
TIMER
DRY
Hr
SLEEP
Min
SLEEP key
Press this key to set SLEEP operation,
and press the "Hr" key to adjust the time
of timer off (it can be choose from 1-7
h o u r s ) , w h e n r e p r e s s t h i s k e y , t h e
operation will stop.
ON/OFF key
Press once to start and press once more
to stop the unit.
DRY key
SEND key
Press this key to transmit the operation,
thescreen will show the operation.
Pressthiskey,theairconditionerwill run
in DRYmode.
●Makesuretoaimthesignalportofremote
controller at the signal receiver indicator of front
panel.
Onlythe AUTO,ON/OFF,SLEEP,SEND keys
could beusedtosendthecurrentdisplayoperation,
the other keys could be used to change the mode.
The other functions please refer to the cooling
only type air conditioner
SEND
NOTE: When using Fahrenheit remote controller
the sign 'Oc', '+Oc' or '-Oc' will be corresponding
changed to 'OF','+OF' or '-OF'.

－12－
●In case of the power off during the operation, all options will be
ceased.
●If need to resume the operation, please repress the "SEND" key. If
thereismalfunctionintheoperationprocedure,orwrongoperation
due to the thunder,pleasepulloutthepowerplug,and reinsert it,
then press the "SEND" key.
POWER OFF
HIGH
TIME
AM
MODE
FAN
SEND
TIMER
DRY
Hr
SLEEP
Min
NAMES AND FUNCTIONS OF THE REMOTE CONTROLLER
MODE key
Press the "MODE" key step by step, the
LCD will display the COOL-FAN-HEAT-
AUTO mode, circularly.
TEMP key
Press once, the SET TEMP. will decrease
1℃. Press once, the SET TEMP. will
increase 1℃. The SET TEMP. can be
selectedfrom16℃-30℃
FAN key
The switchover of FAN mode are HIGH-
MD-LOW.
TIMER key
Press the key to select the SET TIMER mode or
theTIMEmode.Whenselectthe"SETTIMER"
mode, the LCD will display the time of the SET
TIMER mode, while select the "TIME" mode,
the LCD will display the current time.
Hr/Min key
When the unit is running in the "TIME" mode,
press "Hr" once, the number will increase 1,
press "Min" once, the number will increase 1.
When the unit is running in the "SET TIMER"
mode, press the key once between 0-7, the
number of time will increase 0.5, press the key
once above 8, the number of time will increase
1. When the unit is running in "SLEEP" mode,
press the "Hr" key once, the time interval will
increase 1 hour, and will circulate from 1 to 7
hour(s).
ON/OFF
NOTE: When using Fahrenheit remote controller
the sign 'Oc', '+Oc' or '-Oc'will be corresponding
changed to 'OF','+OF' or '-OF'.
(61OF~86ＯF).

－13－
COOLMODE OPERATION
COOL
●When temperature of room sensor is higher
than the set temp, compressor runs, the unit starts
cooling operation.
●When temperature of room sensor is lower
than the set temp, compressor stops, the unit runs
in "FAN" mode.
●The set temp should be in range of 16℃~30℃.
HIGH
TIME
AM
MODE
FAN
SEND
TIMER
DRY
Hr
SLEEP
Min
１８ Ｃ
０
1.After inserting the batteries, press
"ON/OFF" key to start the unit.
2. Press "MODE" key, to choose "COOL"
mode.
3. Press "FAN" key, to set fan speed.
4. Press "TEMP" key, to set the desired
temp.
5. Press "SEND" key, send the operation
to the unit.
ON/OFF
NOTE: When using Fahrenheit remote controller
the sign 'Oc', '+Oc' or '-Oc'will be corresponding
changedto 'OF','+OF' or '-OF'.
(61OF~86ＯF).

－14－
HEAT MODE OPERATION (only for cooling/heating type units)
●When the air conditioner was disturbed, the
remote controller can't work once in a while,
onlytopulloutthepowerplug,afterreinserting
it, it can be operated.
●Check if the voltage of the batteries is full or
not,otherwise to replace the worn batteries.
● When the LCD of the remote controller
couldn'tdisplayallsetcontentsclearly,or
the set options couldn't be received, please
replace the batteries.
The compressor and lower motor stop running,
only PTC is running, the upper motor is running
at the set fan speed.
HEAT
HIGH
TIME
AM
MODE
FAN
SEND
TIMER
DRY
Hr
SLEEP
Min
1. After inserting the batteries, press
"ON/OFF" key to start the unit.
2. Press "MODE" key, to choose "HEAT"
mode.
3. Press "TEMP" key, to set the desired
temp.
4. Press "FAN" key, to set fan speed.
5. Press "SEND" key totransmitthe
operationto the unit.
ON/OFF
NOTE: When using Fahrenheit remote controller
the sign 'Oc', '+Oc' or '-Oc'will be corresponding
changedto 'OF','+OF' or '-OF'.

－15－
DRY MODE OPERATION
When the unit is in DRY mode, the compressor
is protected, the fan motor runs at low fan speed.
DRY
HIGH
TIME
AM
MODE
FAN
SEND
TIMER
DRY
Hr
SLEEP
Min
１８ Ｃ
０
5.Press "SEND" key to transmit the
operationto the unit.
1.After inserting the batteries, press
"ON/OFF" key to start the unit.
2.Press "DRY" key, to set "DRY" mode,
when repress the key, it will run in original
operation.
3.Press "TEMP" key, to set desired temp.
4.Press "FAN" key, to set fan speed.
ON/OFF
NOTE: When using Fahrenheit remote controller
the sign 'Oc', '+Oc' or '-Oc'will be corresponding
changedto 'OF','+OF' or '-OF'.

－16－
SLEEP MODE OPERATION
● When the unit is running in SLEEP mode, press "Hr"
key to set timer on, the interval is 1-7 hours.
● When the unit is running in SLEEP mode, according to
the time changes, it could adjust the original set temp
automatically to save energy and make a comfortable
sleeping.
1. After inserting the batteries, press
"ON/OFF" key to start the unit.
2. Press "MODE" key, to select the
operation mode.
3. Press "TEMP" key, to set desired
temp.
4. Press "FAN" key to set fan speed.
5. Press "SEND" keyto transmit the
operation to the unit.
6. Press "SLEEP" key, to set SLEEP
operation, when press once more it
will stop.
HIGH
TIME
AM
MODE
FAN
SEND
TIMER
DRY
Hr
SLEEP
Min
１８ Ｃ
０
ＳＬＥＥＰ
ON/OFF
NOTE: When using Fahrenheit remote controller
the sign 'Oc', '+Oc' or '-Oc' will be corresponding
changeed to 'OF','+OF' or '-OF'.

－17－
AUTO MODE OPERATION
● According to the room temp, the microcomputer will
adjusttheturnonorturnoffofthecompressorautomatically
to offer comfortable effect.
AUTO MODE
HIGH
TIMER
MODE
FAN
SEND
TIMER
DRY
Hr
SLEEP
Min
1. After inserting the batteries, press
"ON/OFF" key to start the unit.
2. Press "MODE" key, select "AUTO"
mode, according to the room temp, the
microcomputer will adjust the turn on
or turn off of the compressor and fan
motorautomaticallyto offer comfortable
effect.
3. Press "SEND" keyto transmit the
operation to the unit.
ON/OFF
NOTE: When using Fahrenheit remote controller
the sign 'Oc', '+Oc' or '-Oc' will be corresponding
changedto 'OF','+OF' or '-OF'.