Sinclair ASC BI Series User manual

UNI SPLIT SERIES
ASC-xxBI, ASD-xxBI, ASF-xxBI,
ASGE-xxBI, ASGE-xxBI-3
SERVICE MANUAL
EN


“Originalinstructions”
IMPORTANT NOTE:
Read this manual carefully before installing
or operating your new air conditioning
unit. Make sure to save this manual for
future reference.

Foreword
Thank you for choosing Sinclair air conditioners. In order to correctly install and use our units, and for
the satisfactory operation effect, please read this manual carefully.
This manual specifies safe operation requirements from perspectives of product introduction, control,
troubleshooting and maintenance, as well as basic principles and implementation methods. Professional
operators must abide by relevant national (local) safety requirements and technical specifications set forth in this
manual during operations; otherwise, the air conditioning system may fail or be damaged, and personnel safety
accident may also occur.
Safety Notice
The air conditioner is charged with
flammable refrigerant R32.
Before using the air conditioner, please first read the instruction manual.
Before installing the air conditioner, please first read the instruction manual.
Before repairing the air conditioner, please first read the technical service manual.
Compared with common refrigerant, R32 is an environmental-friendly refrigerant that has no harm to the ozone layer and weak
greenhouse effect. Its GWP is 675. Because of its thermodynamic characteristics, R32 requires a smaller charging quantity to reach
high energy efficiency. It is inflammable and odourless, but may cause explosion under certain circumstances.

CONTENTS
Safety Notice on Maintenance.........................................................................................................1
Safety Notice on Operation..............................................................................................................2
1. Product Introduction.....................................................................................................................3
1.1 Lists of Units ...................................................................................................................................... 3
1.2 Electrical Parameters......................................................................................................................... 7
2. Control.........................................................................................................................................9
2.1 Operation Mode................................................................................................................................. 9
2.2 Control Mode ................................................................................................................................... 10
2.3 Functions......................................................................................................................................... 12
3. Troubleshooting.........................................................................................................................20
3.1 Wiring Diagrams .............................................................................................................................. 20
3.2 PCB Layout...................................................................................................................................... 27
3.3 Error Code....................................................................................................................................... 40
3.4 Troubleshooting ............................................................................................................................... 42
3.5 Failures Not Caused by Errors......................................................................................................... 75
4. Maintenance..............................................................................................................................77
4.1 System Diagram .............................................................................................................................. 77
4.2 Connection Pipe Vacuum Pumping.................................................................................................. 77
4.3 Refrigerant Charging........................................................................................................................ 78
4.4 Maintenance of Major Components.................................................................................................. 80
4.5 Removal of Major Components........................................................................................................ 80
4.6 Explosive View and Lists of Parts................................................................................................... 127
Appendices..................................................................................................................................184
1. Resistance/temperature lists of temperature sensors..............................................................184
2. Temperature/Pressure List of Refrigerant................................................................................191
3. Refrigerant Notice/Concentration.............................................................................................192
4. Operation Tools........................................................................................................................193

1
Safety Notice on Maintenance
PROHIBITED：
1. Do not pierce or burn.
2. Please note that refrigerant may be odorless.
3. The appliance shall be stored in a room without continuously operating ignition sources (For example: open
flames, an operating gas appliance or an operating electric heater).
4. Indoor unit adopts special joints that can’t be detached. The installation method is the same with the
common joints. However, because the joint can’t be detached, if it is badly connected and causes leakage,
it needs to be cut and replaced by a new one through welding.
5. Using unsuitable parts or tools may lead to electric shock or fire hazard.
6. If refrigerant leaks during maintenance, please ventilate the room immediately. Heavy leakage may lead to
breathing difficulty, severe injury or death.
7. Disconnect power before disassembling the appliance for maintenance.
8. The appliance should be maintained and cared by authorized technical personnel with necessary
qualifications.
WARNING:
1. If the working place is more than 2m's high, please wear a safety helmet, gloves and a safety belt.
2. Never mix any other substances except the specified refrigerant into the refrigerant circuit.
3. When re-locating the appliance, check whether the new location is strong enough to withstand the weight of
the appliance.
4. If there is refrigerant leak, please fix the leak before charging in the refrigerant. After refrigerant is charged,
check for refrigerant leaks. If you cannot spot the leak, stop the maintenance work. Please evacuate the
system and close the service valve to prevent refrigerant leaking into the room.
5. Prepare suitable tools and protectors.
6. If you need to carry out maintenance or check the electric circuit without cutting off the power, please be
careful not to touch the electrical parts.
NOTICE:
1. If the appliance is maintained at a humid place, it should be grounded to avoid electric shock.
2. Never repair the unit with wet hands. Operating the unit with wet hands may lead to electric shock.
3. If the unit is not correctly grounded, please check and fix it.
4. Before cleaning the unit, please disconnect power to prevent the inner fan from starting up and running at
high speed; otherwise personal injury may occur.
5. Measure the insulation resistance after maintenance. The resistance must be 1M or higher. Bad insulation
may lead to electric shock.
6. Welding and cutting work must be done in a well-ventilated place.
7. Gas appliances, heaters and other fire sources should be kept away from the installation and maintenance
site.
8. Maintenance should be done according to suggestions of the manufacturer.
9. Maintenance should be done only after the refrigerant is completely reclaimed from the unit.
OBSERVED：
1. After the maintenance work is done, check the drainage of indoor unit.
2. Do not tilt the unit, otherwise, water may spill out from the unit and make the floor and furniture wet.

2
3. Disassembly of the unit, handling of the refrigerant, oil and accessories should all be done according to
applicable local rules and regulations.
Safety Notice on Operation
PROHIBITED：
1. Never try to modify the unit, otherwise, it may cause electric shock, overheat or fire hazard.
2. If the power cord or conducting wires are scratched, please replace them.
3. Never use connected or extended power cord or share the power socket with other appliances.
4. Prepare a specialized power circuit for the appliance.
WARNING：
1. If the power plug is dirty, please clean it before inserting it to the power socket. If the power plug is loose,
please tighten it up.
2. Do not damage the power cord. A damaged or refitted power cord may lead to electric shock or fire hazard.
3. Check frequently whether the appliance is in good condition.
NOTICE:
1. After changing the batteries of remote control, please discard them to avoid being swallowed by children.
2. When the unit is working, do not remove the fan cover.
3. Do not use organic solvents to wipe the controller operating panel.
4. Before cleaning the unit, cut off the power supply.

3
1. Product Introduction
1.1 Lists of Units
1.1.1 List of ODUs
Model Power Supply Appearance
V/Ph/Hz
ASGE-12BI
220-240V~50Hz
208-230V~60Hz
ASGE-18BI
ASGE-24BI
ASGE-30BI
ASGE-36BI
ASGE-36BI-3
380-415V 3N~50/60Hz
ASGE-42BI-3
ASGE-48BI-3
ASGE-60BI-3 380-415V 3N~50/60Hz
Note: 1 Ton =12000Btu/h = 3.517kW

4
If one outdoor unit is to be connected with multiple indoor units, the indoor units must have the same cooling capacity and be of the
same type.
1.1.2 List of IDUs
Model
Rated
Cooling/
Hating
Capacity (kw)
Power Supply
Appearance
V/Ph/Hz
Cassette
Type
ASC-12BI
3.5/4.0
220-240V~50Hz
208-230V~60Hz
ASC-18BI
5.0/5.5
ASC-24BI
7.0/8.0
ASC-30BI
8.5/8.8
ASC-36BI 10.0/12.0
ASC-42BI
12.1/13.5
ASC-48BI
13.4/15.5
ASC-60BI
14.5/17.0

5
Model
Rated
Cooling/
Hating
Capacity (kw)
Power Supply
Appearance
V/Ph/Hz
Duct
Type
220-240V~50Hz
208-230V~60Hz
ASD-12BI
3.5/4.0
ASD-18BI 5.0/5.5
ASD-24BI
7.0/8.0
ASD-30BI
8.5/8.8
ASD-36BI
10.0/12.0

6
Model
Rated
Cooling/
Hating
Capacity (kw)
Power Supply
Appearance
V/Ph/Hz
Duct Type
ASD-42BI
12.1/13.5
220-240V~50Hz
208-230V~60Hz
ASD-48BI
13.4/15.5
ASD-60BI
16.0/17.0
Floor Ceiling
Type
ASF-12BI 3.5/4.0
220-240V~50Hz
208-230V~60Hz
ASF-18BI 5.0/5.5
ASF-24BI 7.0/8.0
ASF-30BI 8.5/8.8
ASF-36BI 10.0/12.0

7
Model
Rated
Cooling/
Hating
Capacity (kw)
Power Supply
Appearance
V/Ph/Hz
Floor
Ceiling
Type
ASF-42BI 12.1/13.5
220-240V~50Hz
208-230V~60Hz
ASF-48BI 13.4/15.5
ASF-60BI 16.0/17.0
Note: The outdoor unit is generally suitable to any one of the three types of indoor units with no need of change (limited to cassette
type, duct type and floor ceiling type).
1.2 Electrical Parameters
Model Power supply Circuit breaker
capacity
Min. sectional area of
power cord
V/Ph/Hz A mm2
ASGE-12BI
220-240V~50Hz
208-230V~60Hz
13 1.5
ASGE-18BI 16 2.5
ASGE-24BI 16 2.5
ASGE-30BI 20 4.0
ASGE-36BI 4.025
ASGE-36BI-3
380-415V 3N~50/60Hz
16 2.5
ASGE-42BI-3
16 2.5
ASGE-48BI-3
16 2.5
ASGE-60BI-3
16 2.5
Model Power Supply Fuse Capacity Circuit Breaker
Capacity Min. Sectional Area of
Power Cord
V/Ph/Hz A A mm2
Indoor unit 220-240V~50Hz
208-230V~60Hz 3.15 61.5

8
NOTICE：
①Fuse is located on the main board.
②Install a circuit breaker at every power terminal near the units (indoor and outdoor units) with at least 3mm contact gap. The
units must be able to be plugged or unplugged.
③Circuit breaker and power cord specifications listed in the above table are determined based on the maximum power input of
the units.
④Specifications of power cords listed in the above table are applicable in a working condition where ambient temperature is 40℃
and multi-core copper cable (e.g. YJV copper cable, with insulated PE and PVC sheath) is protected by a conduit, and is
resistant to 90℃in maximum (See IEC 60364-5-52). If working condition changes, please adjust the specifications according
to national standards.
⑤Specifications of circuit breaker are based on a working condition where the working temperature is 40℃. If working condition
changes, please adjust the specifications according to national standards.
⑥Adopt 2pc of 0.75mm²power cords to be the communication cords between indoor and outdoor units. The maximum length is
100m. Please select a proper length according to local conditions. Communication cords must not be twisted together. To be in
compliance with EN 55014, it is necessary to use 8 meters long wire.
⑦Adopt 2pc of 0.75mm²power cords to be the communication cords between wired control and indoor unit. The maximum
length is 30m. Please select a proper length according to local conditions. Communication cords must not be twisted together.
To be in compliance with EN 55014, it is necessary to use 7.5 meters long wire.
⑧The wire gauge of communication cord should not be less than 0.75mm². It’s recommended to use 0.75mm² power cords as
the communication cords.

MODEL
ASGE-12BI ASGE-18BI
Capacity cooling/heating Nominal kW
3,5/4,0 5,0/5,5
Power supply Hz / V
1~ / 50 / 220-240 1~ / 50 / 220-240
Power input cooling/heating W
950/1050 1550/1450
Maximal power input W
1350 1750
Power current cooling/heating A
4,18/4,70 6,50/6,90
Maximal power current A
6,0 8,0
Airflow of OD H m3 / h
3000 3000
Sound pressure of OD in 1m H dB(A)
50 50
Sound power of OD H dB(A)
64 65
Refrigerant type/charge Type / kg / t eq.CO2
R32/0,78/0,53 R32/1,00/0,68
Additional refrigerant g / m
16 16
Pipe diameter - liquid side inch / mm
1/4 / 6,4 1/4 / 6,4
Pipe diameter - gas side inch / mm
3/8 / 9,5 1/2 / 12,7
Standard pipe length m
5 5
Max. allowed pipe length m
30 35
Max. elevation/ Drop height m
15 20
Dimension of OD w x h x d mm
818×596×378 818×596×378
Package dimension of OD w x h x d mm
948×645×420 948×645×420
Weight of OD netto / brutto kg
37/40 39/42
Operating temperature range Cooling °C
–20～48 –20～48
Operating temperature range Heating °C
–20～24 –20～24
ADDITIONAL TECHNICAL INFORMATION
Screw holes distance of OD w x d mm
550x348 550x348
Communication cable mm2
2 x 0,75 2 x 0,75
Recommended power cable mm2
3 x 1,5 3 x 2,5
Recommended air switch A
13 16
MODEL
ASGE-24BI ASGE-30BI
Capacity cooling/heating Nominal kW
7,0/8,0 8,5/8,8
Power supply Hz / V
1~ / 50 / 220-240 1~ / 50 / 220-240
Power input cooling/heating W
2100/2450 2800/2650
Maximal power input W
3500 3950
Power current cooling/heating A
8,80/10,50 12,7/11,7
Maximal power current A
16,0 18,0
Airflow of OD H m3 / h
3600 4000
Sound pressure of OD in 1m H dB(A)
52 53
Sound power of OD H dB(A)
67 69
Refrigerant type/charge Type / kg / t eq.CO2
R32/1,60/1,08 R32/1,80/1,22
Additional refrigerant g / m
40 40
Pipe diameter - liquid side inch / mm
3/8 / 9,5 3/8 / 9,5
Pipe diameter - gas side inch / mm
5/8 / 15,9 5/8 / 15,9
Standard pipe length m
5 5
Max. allowed pipe length m
50 50
Max. elevation/ Drop height m
25 25
Dimension of OD w x h x d mm
892×698×396 920×790×427
Package dimension of OD w x h x d mm
1029×750×458 1083×855×488
Weight of OD netto / brutto kg
53/57 60/65
Operating temperature range Cooling °C
–20～48 –20～48
Operating temperature range Heating °C
–20～24 –20～24
ADDITIONAL TECHNICAL INFORMATION
Screw holes distance of OD w x d mm
560x364 610x395
Communication cable mm2
2 x 0,75 2 x 0,75
Recommended power cable mm2
3 x 2,5 3 x 4,0
Recommended air switch A
16 20

MODEL
ASGE-36BI ASGE-36BI-3
Capacity cooling/heating Nominal kW
10,0/12,0 10,0/12,0
Power supply Hz / V
1~ / 50 / 220-240 3~ / 50 / 380-415
Power input cooling/heating W
3300/3600 3300/3500
Maximal power input W
4050 4650
Power current cooling/heating A
14,5/15,9 5,1/5,6
Maximal power current A
18,5 7
Airflow of OD H m3 / h
5900 5900
Sound pressure of OD in 1m H dB(A)
55 55
Sound power of OD H dB(A)
70 70
Refrigerant type/charge Type / kg / t eq.CO2
R32/2,50/1,69 R32/2,5/1,69
Additional refrigerant g / m
40 40
Pipe diameter - liquid side inch / mm
3/8 / 9,5 3/8 / 9,5
Pipe diameter - gas side inch / mm
5/8 / 15,9 5/8 / 15,9
Standard pipe length m
5 5
Max. allowed pipe length m
65 65
Max. elevation/ Drop height m
30 30
Dimension of OD w x h x d mm
940×820×530 940×820×530
Package dimension of OD w x h x d mm
1073×868×563 1073×868×563
Weight of OD netto / brutto kg
83/95 89/101
Operating temperature range Cooling °C
–20～48 –20～48
Operating temperature range Heating °C
–20～24 –20～24
ADDITIONAL TECHNICAL INFORMATION
Screw holes distance of OD w x d mm
610x486 610x486
Communication cable mm2
2 x 0,75 2 x 0,75
Recommended power cable mm2
3 x 4,0 5 x 2,50
Recommended air switch A
25 16
MODEL
ASGE-42BI-3 ASGE-48BI-3
Capacity cooling/heating Nominal kW
12,1/13,5 13,4/15,5
Power supply Hz / V
3~ / 50 / 380-415 3~ / 50 / 380-415
Power input cooling/heating W
4050/4150 4700/4450
Maximal power input W
5300 5950
Power current cooling/heating A
5,9/6,1 7,2/6,7
Maximal power current A
8 9
Airflow of OD H m3 / h
5900 5900
Sound pressure of OD in 1m H dB(A)
56 57
Sound power of OD H dB(A)
71 72
Refrigerant type/charge Type / kg / t eq.CO2
R32/2,65/1,79 R32/2,8/1,89
Additional refrigerant g / m
40 40
Pipe diameter - liquid side inch / mm
3/8 / 9,5 3/8 / 9,5
Pipe diameter - gas side inch / mm
5/8 / 15,9 5/8 / 15,9
Standard pipe length m
5 7,5
Max. allowed pipe length m
75 75
Max. elevation/ Drop height m
30 30
Dimension of OD w x h x d mm
940×820×530 940×820×530
Package dimension of OD w x h x d mm
1073×868×563 1073×868×563
Weight of OD netto / brutto kg
95/107 99/111
Operating temperature range Cooling °C
–20～48 –20～48
Operating temperature range Heating °C
–20～24 –20～24
ADDITIONAL TECHNICAL INFORMATION
Screw holes distance of OD w x d mm
610x486 610x486
Communication cable mm2
2 x 0,75 2 x 0,75
Recommended power cable mm2
5 x 2,5 5 x 2,5
Recommended air switch A
16 16

MODEL
ASGE-60BI-3
Capacity cooling/heating Nominal kW
16,0/17,0
Power supply Hz / V
3~ / 50 / 380-415
Power input cooling/heating W
5450/5400
Maximal power input W
5950
Power current cooling/heating A
7,7/7,6
Maximal power current A
9
Airflow of OD H m3 / h
6600
Sound pressure of OD in 1m H dB(A)
57
Sound power of OD H dB(A)
72
Refrigerant type/charge Type / kg / t eq.CO2
R32/3,6/2,43
Additional refrigerant g / m
40
Pipe diameter - liquid side inch / mm
3/8 / 9,5
Pipe diameter - gas side inch / mm
5/8 / 15,9
Standard pipe length m
7,5
Max. allowed pipe length m
75
Max. elevation/ Drop height m
30
Dimension of OD w x h x d mm
900×1345×412
Package dimension of OD w x h x d mm
1033×1395×443
Weight of OD netto / brutto kg
112/122
Operating temperature range Cooling °C
–20～48
Operating temperature range Heating °C
–20～24
ADDITIONAL TECHNICAL INFORMATION
Screw holes distance of OD w x d mm
572x378
Communication cable mm2
2 x 0,75
Recommended power cable mm2
5 x 2,5
Recommended air switch A
16

MODEL ASC-12BI / ASGE-12BI ASC-18BI / ASGE-18BI
Capacity cooling/heating Nominal kW 3,5/4,0 5,0/5,5
Power supply Hz / V 1~ / 50 / 220-240 1~ / 50 / 220-240
Energy class cooling - A+ A+
Pdesign cooling kW 3,5 5,0
SEER - 5,9 5,9
Annual power consumption kWh 213 296
Energy class heating Average climate - A+ A+
Pdesign heating Average climate kW 3,1 4,0
SCOP Average climate - 4,0 4,0
Annual power consumption Average climate kWh 1069 1405
Air flow of ID MH/H/M/L m
3
/ h 650/580/480/400 700/580/480/400
Sound pressure of ID in 1,4m MH/H/M/L dB(A) 39 / 36 / 33 44/39/36/33
Sound power of ID MH dB(A) 57 53
External static pressure nom/min-max Pa - -
Dehumidifying volume l / h - -
Refrigerant type Type R32 R32
Pipe diameter - liquid side inch / mm ¼ / 6,4 ¼ / 6,4
Pipe diameter - gas side inch / mm ⅜ / 9,5 ½ / 12,7
Dimension of ID w x h x d mm 570×265×570 570×265×570
Dimension of panel w x h x d mm 620×47,5×620 620×47.5×620
Package dimension of ID w x h x d mm 698×295×653 698x295x653
Package dimension of panel w x h x d mm 701×125×701 701×125×701
Weight of ID netto / brutto kg 17/22 17/22
Weight of panel netto / brutto 3,0 / 4,5 3,0 / 4,5
Set temperature range °C 16～30 16～30
MODEL ASC-24BI / ASGE-24BI ASC-30BI ASGE-30BI
Capacity cooling/heating Nominal kW 7,0 (0,76-7,34) / 8,0 (1,63-8,43) 8,5 (1,03-8,92) / 8,8 (1,95-9,11)
Power supply Hz / V 1~ / 50 / 220-240 1~ / 50 / 220-240
Energy class cooling - A++ A++
Pdesign cooling kW 7,0 8,5
SEER - 7,2 6,1
Annual power consumption kWh 340 472
Energy class heating Average climate - A A+
Pdesign heating Average climate kW 6,4 7,2
SCOP Average climate - 3,9 4,0
Annual power consumption Average climate kWh 2297 2616
Air flow of ID MH/H/M/L m
3
/ h 1100/1050/960/870 1400/1310/1180/1040
Sound pressure of ID in 1,4m MH/H/M/L dB(A) 43/42/40/39 49/47/44/41
Sound power of ID MH dB(A) 52 58
External static pressure nom/min-max Pa - -
Dehumidifying volume l / h - -
Refrigerant type Type R32 R32
Pipe diameter - liquid side inch / mm ⅜ / 9,5 ⅜ / 9,5
Pipe diameter - gas side inch / mm ⅝ / 15,9 ⅝ / 15,9
Dimension of ID w x h x d mm 840×240×840 840×240×840
Dimension of panel w x h x d mm 950×52×950 950×52×950
Package dimension of ID w x h x d mm 963×325×963 963×325×963
Package dimension of panel w x h x d mm 1033×112×1038 1033×112×1038
Weight of ID netto / brutto kg 29/36 29/36
Weight of panel netto / brutto 6,0/9,5 6,0/9,5
Set temperature range °C 16～30 16～30

MODEL ASC-36BI / ASGE-36BI ASC-36BI / ASGE-36BI-3
Capacity cooling/heating Nominal kW
10,0 (1,17-10,59) / 12,0 (2,61-12,42) 10,0 (1,17-10,59) / 12,0 (2,61-12,42)
Power supply Hz / V 1~ / 50 / 220-240 1~ / 50 / 220-240
Energy class cooling - A++ A++
Pdesign cooling kW 10,0 10,0
SEER - 6,1 6,1
Annual power consumption kWh 566 533
Energy class heating Average climate - A+ A+
Pdesign heating Average climate kW 9,0 9,0
SCOP Average climate - 4,0 4,0
Annual power consumption Average climate kWh 3139 3168
Air flow of ID MH/H/M/L m
3
/ h 1500/1470/1380/1220 1500/1470/1380/1220
Sound pressure of ID in 1,4m MH/H/M/L dB(A) 50/48/46/42 50/48/46/42
Sound power of ID MH dB(A) 59 59
External static pressure nom/min-max Pa - -
Dehumidifying volume l / h - -
Refrigerant type Type R32 R32
Pipe diameter - liquid side inch / mm ⅜ / 9,5 ⅜ / 9,5
Pipe diameter - gas side inch / mm ⅝ / 15,9 ⅝ / 15,9
Dimension of ID w x h x d mm 840×240×840 840×240×840
Dimension of panel w x h x d mm 950×52×950 950×52×950
Package dimension of ID w x h x d mm 963×325×963 963×325×963
Package dimension of panel w x h x d mm 1033×112×1038 1033×112×1038
Weight of ID netto / brutto kg 31/38 31/38
Weight of panel netto / brutto 6,0/9,5 6,0/9,5
Set temperature range °C 16～30 16～30
MODEL ASC-42BI / ASGE-42BI-3 ASC-48BI / ASGE-48BI-3
Capacity cooling/heating Nominal kW 12,1 (1,51-12,7) / 13,5 (3,09-13,97)
13,4 (1,71-14,06) / 15,5 (3,20-16,04)
Power supply Hz / V 1~ / 50 / 220-240 1~ / 50 / 220-240
Energy class cooling - A++ A++
Pdesign cooling kW - -
SEER - 6,1 6,1
Annual power consumption kWh - -
Energy class heating Average climate - A A+
Pdesign heating Average climate kW - -
SCOP Average climate - 3,8 4,0
Annual power consumption Average climate kWh - -
Air flow of ID MH/H/M/L m
3
/ h 1800/1690/1470/1260 1900/1690/1480/1140
Sound pressure of ID in 1,4m MH/H/M/L dB(A) 51/49/46/42 52/51/48/45
Sound power of ID MH dB(A) 60 61
External static pressure nom/min-max Pa - -
Dehumidifying volume l / h - -
Refrigerant type Type R32 R32
Pipe diameter - liquid side inch / mm ⅜ / 9,5 ⅜ / 9,5
Pipe diameter - gas side inch / mm ⅝ / 15,9 ⅝ / 15,9
Dimension of ID w x h x d mm 840×240×840 840×240×840
Dimension of panel w x h x d mm 950×52×950 950×52×950
Package dimension of ID w x h x d mm 963×325×963 963×325×963
Package dimension of panel w x h x d mm 1033×112×1038 1033×112×1038
Weight of ID netto / brutto kg 33/41 36/44
Weight of panel netto / brutto 6,0/9,5 6,0/9,5
Set temperature range °C 16～30 16～30

MODEL ASC-60BI / ASGE-60BI-3
Capacity cooling/heating Nominal kW 16,0 (2,02-15,22) / 17,0 (3,54-17,59)
Power supply Hz / V 1~ / 50 / 220-240
Energy class cooling - A++
Pdesign cooling kW -
SEER - 6,1
Annual power consumption kWh -
Energy class heating Average climate - A
Pdesign heating Average climate kW -
SCOP Average climate - 3,8
Annual power consumption Average climate kWh -
Air flow of ID MH/H/M/L m
3
/ h 2000/1880/1620/1430
Sound pressure of ID in 1,4m MH/H/M/L dB(A) 54/52/50/48
Sound power of ID MH dB(A) 63
External static pressure nom/min-max Pa -
Dehumidifying volume l / h -
Refrigerant type Type R32
Pipe diameter - liquid side inch / mm ⅜ / 9,5
Pipe diameter - gas side inch / mm ⅝ / 15,9
Dimension of ID w x h x d mm 840×240×840
Dimension of panel w x h x d 950×52×950
Package dimension of ID w x h x d mm 963×325×963
Package dimension of panel w x h x d 1033×112×1038
Weight of ID netto / brutto kg 36/44
Weight of panel netto / brutto 6,0/9,5
Set temperature range °C 16～30