Sinclair SWC-03 User manual

WIRED CONTOLLER
SWC-03
USER'S MANUAL
EN


“Originalinstructions”
IMPORTANT NOTE:
Read this manual carefully before installing
or operating your new air conditioning
unit. Make sure to save this manual for
future reference.

User Notices
For correct installation and operation, please read all instructions carefully.
Before reading the instructions, please be aware of the following items:
Prohibit installing the wired controller at wet or sunshine places.
Do not knock, throw or frequently disassemble the wired controller.
Do not operate the wired controller with wet hands.
Do not remove or install the wired controller by yourself. If there is any
question, please contact our after-sales service center.
The wired controller is a general model, applicable for several kinds of units.
Some functions of the wired controller are not available for certain kinds of
units, more details please refer to the owner’s manual of unit. The setting of
such unavailable function will not affect unit’s operation.

Contents
1 DISPLAY.....................................................................................................1
1.1APPEARANCE..........................................................................................1
1.2 INSTRUCTIONS FOR RELATED DISPLAYED SYMBOLS .................................2
2 BUTTONS...................................................................................................4
2.1 BUTTON GRAPHICS.................................................................................4
2.2 FUNCTION INSTRUCTIONS OF BUTTONS ...................................................5
3 OPERATION INSTRUCTIONS...................................................................6
3.1 MENU STRUCTURE .................................................................................6
3.2 ON/OFF .................................................................................................8
3.3 MODE SETTING ......................................................................................8
3.4TEMPERATURE SETTING..........................................................................9
3.5 FAN SETTING..........................................................................................9
3.6 SWING SETTING ...................................................................................10
3.7 FUNCTIONS SETTING ............................................................................13
3.8 UNIT STATUS VIEW ...............................................................................23
3.9 CURRENT ERROR VIEW ........................................................................25
3.10TIMER SETTING ..................................................................................27
3.11 CLOCK SETTING .................................................................................38
3.12 LOCK SETTING ...................................................................................41
4 INSTALLATION INSTRUCTIONS............................................................42
4.1 PARTS AND DIMENSION OF WIRED CONTROLLER....................................42

4.2 INSTALLATION REQUIREMENTS ..............................................................43
4.3 INSTALLATION METHODS .......................................................................44
4.4 DISASSEMBLY.......................................................................................46

1
1 Display
1.1Appearance
Fig.1 Appearance of wired controller

2
1.2 Instructions for Related Displayed Symbols
No. Symbols
Instructions
1
Up and down swing function
2
Left and right swing function
3
Fresh air function
4
Sleep function
5
Auto mode
6
Cooling mode
7
Dry mode
8
Fan mode
9
Heating mode
10
Health function
11
I-Demand function
12
Absence function
13
Shielding status (Buttons, temperature, ON/OFF, mode or
energy saving is shielded by remote monitor)

3
No. Symbols
Instructions
14
Current set fan speed
15
Memory function (Memory in power failure)
16
Save function
17
X-fan function
18
Remind to clean the filter
19
Timer on status
20
Gate card pulled-off status or nobody presented status
21
Quiet function
22
Function lock

4
2 Buttons
2.1 Button Graphics
Fig. 2 Button graphics

5
2.2 Function Instructions of Buttons
No. Button name Button Function
1 FAN Set low speed, low-medium speed, medium speed,
medium-high speed, high speed, turbo and auto speed.
2 ∧(1) Set temperature
(2) Set parameter
(3) Move option cursor
6 ∨
3
ON/OFF/BACK
(1) Turn on or turn off unit
(2) Return to last page
4 SWING Set up&down swing and set left&right swing
5
＜
(1) Set related function on or off
(2) Move option cursor
(3) Set parameter
8
＞

6
No. Button name Button Function
7 MENU/OK (1) Enter menu page
(2) Confirm setting
9 MODE Set auto, cooling, dry, fan and heating modes for indoor
unit.
3 Operation Instructions
3.1 Menu Structure
Normal setting of wired controller can be set directly on the main
page, including fan speed, swing, set temperature, mode, ON/OFF. The
setting and status view of other functions can be set in corresponding
submenu. Detailed menu structure is as shown in Fig. 3.

7
Fig. 3 Menu structure
Main menu
User function menu
Air function setting
Sleep function setting
Health function setting
I-DEMAND function setting
Absence function setting
Clean function setting
Fixed-angle swing function setting
Save function setting
Auxiliary heat function setting
Dry function setting
Quiet function setting
Fahrenheit setting
Memory function setting
Low temperature dry function
Timer setting menu
Once
Daily
Weekly timer
Two week timer
Countdown timer on
Countdown timer off
Clock setting menu
Time format setting
Clock setting
View function menu
Unit status view
Current error view
Function lock menu
Unit ON/OFF lock
Mode setting lock
Temperature setting lock
Fan speed setting lock
Key lock

8
3.2 On/Off
When the wired control is on main page, press ON/OFF button to turn
on the unit. Press ON/OFF button again to turn off the unit. The interfaces
of On/Off status are shown in Fig. 4 and Fig. 5.
Fig. 4 Off interface Fig. 5 On interface
3.3 Mode Setting
Under On status, pressing MODE button can set mode circularly as:

9
Note: If save function is on, auto mode is not available.
3.4 Temperature Setting
Under unit on status, pressing “∧” or “∨” button on the main page
increases or decreases set temperature by 1℃(1℉); holding “∧” or “∨”
button increases or decreases set temperature by 1℃(1℉) every 0.3s.
In cooling, dry, fan and heating mode, temperature setting range is
16℃~30℃(61℉～86℉). Under auto mode, set temperature cannot be
adjusted.
3.5 Fan Setting
Under On status, pressing FAN button can set fan speed circularly
as:
Low→Medium low→Medium→Medium high→High→Turbo→Auto→Low
Symbols displayed are as shown in Fig. 6.
Fig. 6 Fan setting

10
3.6 Swing Setting
In unit on status, press SWING button for swing setting. Two swing
modes are available: fixed-angle swing and simple swing.
When fixed-angle swing mode is set, swing operation is as follows:
In unit on status, press SWING button to select up&down swing .
Up&down swing angle will be adjusted circularly as below:
→→→→→→→ → → → →
closed →
Select up&down swing and left&right swing through “＜” or “＞”
button. When left&right swing is selected. Left&right swing angle will
be adjusted circularly as below:
→→→→→→→ →
closed→
Note:
①Turn on fixed-angle swing mode in function setting page;
①If fixed-angle swing is not available for the model, fixed-angle swing will be
invalid when the wired controller turns on fixed-angle swing mode.

11
Simple swing mode: when fixed-angle swing mode is turned off,
swing operation is as below:
Pressing SWING button under unit on status, up&down swing frame
occurs. Then press SWING button to turn on or turn off up&down swing.
is displayed when up&down swing is on and is not displayed when
up&down swing is off. When up&down swing frame have not disappeared,
press “＜” or “＞” button to switch to left&right swing setting. Then
left&right swing frame occurs. In this case, press SWING button to turn on
or turn off left&right swing. is displayed when left&right swing is on
and is not displayed when left&right swing is off. For detailed operation,
please refer to Fig. 7.

12

13
Fig. 7 Swing setting
3.7 Functions Setting
Press MENU/OK button on main page to enter main menu page.
Press “∧” or “∨”or “＜” or “＞”button to select the function setting
symbol. Then press MENU/OK button to enter user function setting page.
Press “∧” or “∨”button to select specific function item. Press “＜” or “＞”
button to turn on or turn off this function. If the function item cann’t be set,
it will displays with gray color.Please refer to Fig. 8.

14
Fig. 8 Function setting

15
3.7.1 Fresh Air Function Setting
After entering user function page, press “∧” or “∨” button to select
fresh air function and press “＜” or “＞” button to turn on or turn off air
function. Press MENU button to adjust the mode of fresh air.
After entering fresh air mode setting, press “∧” or “∨” button to
adjust the mode in the range of 1~10. After setting, press MENU button
to save the setting.
The each mode means as follows:
1――The unit continuously runs for 60min, and fresh air valve runs
for 6 min.
2――The unit continuously runs for 60min, and fresh air valve runs
for 12 min.
3――The unit continuously runs for 60min, and fresh air valve runs
for 18 min.
4――The unit continuously runs for 60min, and fresh air valve runs
for 2 4 min.
5――The unit continuously runs for 60min, and fresh air valve runs
for 30 min.