Singtech EG360 User manual

SINGTECH EG360 Alarm System 1 10170361A
EG360 ALARM SYSTEM
Operations Manual
Simplifying your needs

EG360 Hands-Free Entry System ith Dynamic Immobilizer &
Smart Anti-HiJack &Foot Brake Lock System Features
1. Auto-Unlock
The system UNLOCKS the vehicle when the user is approximately 2 meters away and trigger waves
are sent to the transponder to confirm user s presence. 2 seconds after the system is UNLOCKED,
the vehicle enters immobilizer Mode.
2. Dynamic Immobilizer
The Immobilizer function will be automatically disabled when the system performs Hand-Shake
confirmation with the transponder upon inserting the key and turning ON the ignition. The vehicle
CANNOT be started with just the key as the transponder must be present as well when attempting
to start the vehicle.
3. Smart Anti-hijack
When Anti-Hijack Mode is set to ON, if any doors are opened and closed anytime after Ignition ON,
the system will check-in with the transponder after 2 minutes. If the transponder is not present
after 60 consecutive checks (approx. 30 seconds), the system enters Anti-Hijack Mode, activating
Starter Disable or Petroleum Pump Disable depending which is installed. *The use of Starter
Disable or Petroleum Pump Disable is recommended instead of Engine Block Disable.
4. Passive Lock
While in Immobilizer Mode, whenever the vehicle doors are opened and closed, the
system will check with the transponder and LOCK the vehicle when its not in range.
* If the user is going to work/stay around the vehicle for an extended amount of time, it's
recommended to turn off all EG360 features temporarily in order to avoid unnecessary drain of
transponder battery [Please refer to page 4 Button 2 b and c ].
5. Automatic Re-Lock
The system will Re-LOCK the vehicle if 1 of 2 conditions applies: 1) The user enters and leave the
Detection Zone without opening the doors; 2) The user opens and closes the doors without
turning on the ignition and leave.
6. Smart Transponder Lo Battery Warning
When arm the system, horn chirp once, parking light flashes 4 times. When press disarm chip
twice, parking lights flashes 5 times. [For normal operation, please refer to page 4 Button 1 ].
SINGTECH EG360 Alarm System 2 10170361A

7. Foot Brake Lock
Closed all doors, Turn ON the ignition, step brake pedal once, the door will be locked. Once ignition
OFF, door will unlock.
8. Door Unlock Warning
EG360 Function Enable *If the door has not closed properly, the parking light will blink 11 times
and following the door will lock.
EG360 Function Disable *If the door doesn't close properly when you press the lock/ unlock
button the parking light with start to blink and car horn will sound too.
9. Reset Alarm
Ignition 'ON', press over ride switch 1 second.
EG360 SINGTECH Transmitter Operation Guild
Basic function of button :
Button 1 : a. Arm: Chirps once, parking light flash once.
b. Disarm: Parking light flash twice.
Button 2 : a. Car finder: Press twice, chirps twice parking light flash six times.
b. EG360 disable: Press 2 seconds: parking light on 2 seconds.
c. EG360 enable: Press 1 second, parking light on 1 second.
Button 1+2 : Press and hold button 1+2 for 3 seconds to activate trunk release
(optional) Note : If you use over-ride switch to disarm, EG360 feature will be by-
passed, user can press side button 2 on transmitter to enable again.
Note: when the user activate EG360 on 1st Transmitter(TX), the 2nd (TX) will enter to sleep mode. If
SINGTECH EG360 Alarm System 3 10170361A
Button 1
LED
Button 2

user uses 2nd (TX)and walk near the car, the 2nd (TX)will not auto unlock the car.
The user must press button 1 on the 2nd (TX) to activate the system. Once the 2nd (TX) is in use, the
1st (TX) will enter to sleep mode.
Troubleshooting Questions
1. Why I approach the car the doors don't unlock?
First of all, you need confirm EG360 function is enabled, please refer your user manual.
2. Why my spare remote cannot ork on keyless entry?
The system will recognize the last remote control which has been activated automatic keyless entry
function; the spare remote control will disable or in the standby mode for automatic lock / unlock
function.
3. Ho to activate the spare remote control automatic lock/unlock function?
Press the big button for 1 second, parking light will flash 1 second to confirm that it is activated.
4. When do I kno that the battery is lo ?
Arm the system, horn chirp once, parking light flashes 4 times. If disarm, horn chirp twice, parking
lights flashes 5 times. Regular response: when arm the system, horn chirp once, parking light
flashes 1 time, When disarm just parking lights flashes 2 times.
5. When the battery is lo , ho should I operate ?
The remote key enters passive backup mode while the battery is low and press Button ONE to
unlock.
6. Does any external conditions may impact the EG360?
If your car surround by Low Frenquency signal (e.g at service station), it may result in the EG360
function disable , because transmitter communicate with transponder via an low frequency,
however, you can operate via press unlock button in this condition.
7. Does this systems drain the vehicle's battery?
No, it doesn't. If the transmitter standby excesses 48 hours, it will enters vacation mode, and it
consumes the power in the minimum level.
SINGTECH EG360 Alarm System 4 10170361A

Battery Installation and replacement
SINGTECH EG360 Alarm System 5 10170361A