SINGULARITY COMPUTERS Eclipse Series User manual

vv
Revision 2.2

Spectre 3.0 Integra, Integra Umbra Limited Edition &
Integra Umbra Chrome Elite Limited Edition Assembly Manual
Revision 2.2
Page | 1
Table of Contents
Introduction................................................................................................................................................... 2
Spectre 3.0 Integra Features..................................................................................................................... 4
Spectre 3.0 Integra Specifications ........................................................................................................... 6
Included Items............................................................................................................................................... 8
Warranty ........................................................................................................................................................ 9
Table of Fasteners & Panels.....................................................................................................................10
Assembly Manual........................................................................................................................................12
Step 1: Install ARGB 50cm LED Strips. .........................................................................................................12
Step 2: Install Power Button.......................................................................................................................... 13
Step 3: Install LED Covers onto Radiator Panels.....................................................................................14
Step 4: Assemble Legs..................................................................................................................................... 15
Step 5: Assemble PSU Shroud........................................................................................................................16
Step 6: Install Legs onto Distribution Plate.............................................................................................. 17
Step 7: Install Radiator Panels onto Legs..................................................................................................18
Step 8: Install PSU Shroud, Cable Shroud & Rear IO...............................................................................19
Step 9: Install PCIe 4.0 Vertical GPU Mount............................................................................................. 20
Step 10: Install PCIe 4.0 2nd Vertical GPU Mount......................................................................................21
Step 11: Install SSD Tray into PSU Shroud................................................................................................. 22
Step 12: Install D5 Pump (Not included).................................................................................................... 23
Step 13: Install Side Panel Window............................................................................................................. 24
Step 14: Filling & Draining The Loop........................................................................................................... 25
Installing Radiators ................................................................................................................................... 25
Liquid Cooling System Layout ................................................................................................................. 26
Spectre 3.0 Integra PowerBoard ............................................................................................................ 27

Spectre 3.0 Integra, Integra Umbra Limited Edition &
Integra Umbra Chrome Elite Limited Edition Assembly Manual
Revision 2.2
Page | 2
Introduction
Spectre 3.0 Integra
The next generation of Spectre has arrived with a new level of integration. Spectre 3.0 Integra
has much of the water-cooling loop integrated with a completely new distribution plate design,
with further enhancements to performance, filling and draining compared to previous Spectre
versions. It has a fully integrated solution/replacement for cables with the Singularity Computers
PowerBoard. Previously we have created PowerBoards for existing cases, but for Integra we have
developed the PowerBoard and case together. This means that both have become far more
streamlined, meaning more features and compatibility. The PowerBoard supports the most high-
end components with x4 8pin EPS and x6 8pin PCIE. The case has more support for larger and
wider motherboards than previous Spectre 3.0 versions. The PowerBoard has a range of new
features, including built in filter capacitors, more integrated LEDs facing inwards and outwards,
integrated direct connect SATA, power, and reset buttons, and a touch activated power button.
There is now no rear access needed to the distribution plate layer due to the fully integrated
PowerBoard, so all cables can be connected from the front and little to no cable management is
needed. Black sleeved linking cables are included with the case, so no cables need to be
purchased separately. Custom colored sleeved linking cables can be purchased separately if
desired. Integra has improved lighting features with integrated PowerBoard LEDs facing inwards
towards the motherboard tray and outwards towards the distribution plate. There are two
separate sets of LEDs for ARGB or UV, and they can be switched on or off, or from UV to ARGB via
two switches on the PowerBoard.
Spectre 3.0 Integra Umbra Limited Edition
Umbra Definition:
The fully shaded inner region of a shadow cast by an opaque object, especially the area on the
earth or moon experiencing the total phase of an eclipse.
Spectre 3.0 Integra Umbra Limited Edition is the final case in the Eclipse series which includes
Penumbra and Antumbra. Umbra is the darkest of the three cases and is a whole new case design
based on the new Spectre 3.0 Integra platform. The design is inspired by fighter aircraft and
spacecraft. Umbra has a more complex and high-end distribution plate compared to the standard
Spectre 3.0 Integra with unique 3-layer design which uses different thicknesses on the same
layer. It has a clear front layer and motherboard tray, grey tinted central layer, clear rear
distribution plate layer and a satin black rear layer which is split into multiple parts. The
motherboard tray has etching which is lit up by the PowerBoard ARGB and/or UV LEDs, the
etching includes a star system coordinate which is unique for each of the 48 cases. The limited-
edition number glows and appears on the rear of the distribution plate. Umbra also has a different
glowing PSU Side shroud with etching to match the motherboard tray.

Spectre 3.0 Integra, Integra Umbra Limited Edition &
Integra Umbra Chrome Elite Limited Edition Assembly Manual
Revision 2.2
Page | 3
Spectre 3.0 Integra Umbra Chrome Elite Limited Edition
In contrast to the dark themed Umbra, we have created an extremely limited silver mirror chrome
version. There will only be three of these cases made due to the complexity involved in chrome
plating each of the 23 metal parts of the case. Each 6061 CNC machined aluminium component
first needs to be manually polished before it can be chrome plated which takes many hours. The
distribution plate is different to the Umbra distribution plate with an extra layer. It has a clear
front layer and motherboard tray, grey tinted central layer, clear rear distribution plate layer and
two rear chrome layers facing forwards and backwards. The two mirrored layers create
reflections from both the inside and outside of the case. There are also reflections all around from
the case panels. The mirrored distribution plate layer reflects the light from the integrated
PowerBoard LEDs out towards all the case panels. The limited-edition number glows on the rear
of the distribution plate, and on the motherboard tray we will etch the coordinates to a star
system of your choosing (please add this to the notes on your order). A special Umbra version
glowing PSU Side Shroud is also included which is clear frosted and chrome.

Spectre 3.0 Integra, Integra Umbra Limited Edition &
Integra Umbra Chrome Elite Limited Edition Assembly Manual
Revision 2.2
Page | 4
Spectre 3.0 Integra Features
•Integrated Liquid Cooling Features
Reservoir, D5 Pump Top, D5 Pump Cover, Fill Port, Drain Port, parts of the cooling loop.
•PowerBoard Integration
The PowerBoard is a PCB integrating 24pin, PCIE and EPS along with PWM and ARGB Hubs,
SATA and Power and Reset Buttons. The Spectre 3.0 Integra PowerBoard also has an integrated
touch sensing Power Button. The PowerBoard has x20 ARGB LEDs positioned around the
external and internal perimeter to optimally light up the distribution plate. Essentially the
PowerBoard is a distribution plate for cables also integrating other features and functions. It
is a new method for cables allowing standardization of cable lengths and making cable
management no longer necessary. Spectre 3.0 Integra comes included with a standard set of
black sleeved linking cables including 24pin x1, 8pin EPS x2, 8pin PCIE x3 meaning that these
cables don’t have to be purchased separately.
•Reduced build time due to integration
With the pump, reservoir, fill and drain ports, half of the water-cooling loop, the core
component cables, PWM and ARGB hubs all integrated there is less assembly to be done. Also,
less fittings and tube are needed. No cable management for the core component cables thanks
to the PowerBoard integration.
•Integration Cost Component
A large portion of the case cost is due to the integration. These are components you do not
have to purchase for your build. The pump top, reservoir, cables, hubs, less fittings, less tube,
no cable combs, or cable management components.
•Compatibility
Theoretically the more integration the less compatibility. For Spectre Integras integration,
each port and connector were positioned based on an average of a vast range of components.
•Integration & Optimization
With the integration we did not just develop a case, we also developed all the integrated
components. This meant that we could focus more on optimization than would normally be
possible. The integrated loop routes in Spectre allow for more flow than 16mm tubes. The
pump top was designed for the D5 pump, maximizing flow to and from the distribution plate.
The reservoir was designed to remove air as quickly as possible making the loop easier to fill.
The fill port is at the highest point on the back for the case and the drain point at the lowest
point.
•High End Components
Spectre 3.0 Integra fits XL-ATX motherboards and has 8 expansion slots. It is designed for fit
the largest high-end GPUs. It can fit the largest PSUs up to 220mm. For the water-cooling

Spectre 3.0 Integra, Integra Umbra Limited Edition &
Integra Umbra Chrome Elite Limited Edition Assembly Manual
Revision 2.2
Page | 5
system it can fit 2x 360mm radiators 60mm thick with a single set of fans or 2x 360mm
radiators 40mm thick with two sets of fans, and the D5 pump. The PowerBoard can handle the
most high-end PSUs and components.
•Radiator Adjustment
The radiator mounting panels have a large range of adjustment to help with port alignment to
the distribution plate.
•Storage
Spectre 3.0 Integra has 7x 2.5” Drive positions. Two are on the top of the PSU shroud, four inside
of the PSU shroud and there is one integrated on the PowerBoard. The two on top of the PSU
shroud cannot be used with vertically mounted GPUs.
Design & Engineering
We are all experienced system builders at Singularity Computers having built high end water-
cooled systems for over 15 years. Our approach to product development begins with a need for
our own builds and so the origin is always function. From there we start to build ideas around this
function and the aesthetics and everything else follows. The original idea for Spectre came from
our years of building highly customized, high end water-cooled systems and trying to reduce the
exceptionally long build times and complexity. Our approach to development is hands on, we are
using our own products every day.
The aesthetics of Spectre originate from its function with one of the main aesthetic features (the
distribution plate lighting) being something only made possible by the integration. We wanted
the case to look skeletal and almost transparent enough to (in a way) disappear around the
components. The metal components have been designed to enhance this with an extreme focus
on detailed and complex multi sided CNC machining.
Manufacturing & Quality
Every component of Spectre is CNC machined from a solid block of material. With the level of
transparency and being an open case, we wanted it to be a celebration of the raw materials. There
is no hidden or back side, and this also goes for the components being installed. Due to this we
selected the most high-end materials manufacturing process. The Distribution Plate is machined
on a CNC router built from thick sheets of cast acrylic. It is hand assembled with silicone gaskets
and stainless-steel fasteners, and pressure tested. The metal components are machined with
Extreme Precision from solid blocks of 6061 aluminum on a CNC mill then sand blasted and
anodized.

Spectre 3.0 Integra, Integra Umbra Limited Edition &
Integra Umbra Chrome Elite Limited Edition Assembly Manual
Revision 2.2
Page | 6
Spectre 3.0 Integra Specifications
Water-cooling Integration
Reservoir, Pump Top, Pump Cover, Fill Port, Drain Port, Parts of water-cooling
loop.
Ports 6x G1/4” BSPP | 1x Fill Port | 1x Drain Port
Pump Compatible with all D5 pumps (Not included)
Electronics Integration Core Component Cable Connections: 24pin x1 | 8pin PCIe x6 | 8pin EPS x4
(As many inputs must be used as outputs).
Hubs: PWM: x6. ARGB: x10 (Single input for each).
LEDs: x20 Integrated ARGB 90-degree LEDs and x15 UV 90-degree LEDs facing
around the internal and external perimeter of the PowerBoard
There are two switches on the PowerBoard one switches the ARGB on or off and
the other switches the UV on or off.
Touch sensing Power Button.
Extra Power and Reset Buttons.
PowerBoard LED on/off switch. (Requires reboot for setting to take effect).
PowerBoard 2.5” SATA 3.0 6Gb/s Direct Mount x1.
Cables PowerBoard Linking Cables Standard Set: 24pin x1| 8pin EPS x2| 8pin PCIe x3
18AWG Black Heatshrinkless Sleeve.
Linking cables and PSU Side Cables available here.
Adaptors for motherboards with 90-degree connectors available here.
PWM Female to Female 50cm Black Sleeved x1.
ARGB Female to Female 50cm Black Sleeved x1.
LED strips
Integra: 2x 50cm ARGB LED Strips with 50cm cables.
Integra Umbra (all variants): 3x 50cm ARGB LED Strips with 50cm cables.
(1x 30cm LED strip pre-installed into PSU Side Shroud.)
Attach to case panels on specific mounting points for front and top panel glow.
Motherboard Form Factor XL-ATX (Up to: 285mm Wide & 343.5mm High) E-ATX, ATX, Mini-DTX, Mini-ITX.
Expansion Slots 8x
Case Form Factor Mid Tower
Package Dimensions &
Weight
640 mm(L) x 620 mm(W) x 110 mm(H)
(Flat-packed Case | Partial assembly required) | 17 Kg
Case Dimensions & Weight 545 mm(L) x 254 mm(W) x 595 mm(H) | 15 Kg
Storage
7x 2.5” Drive
x2 are on top of the PSU shroud and cannot be used when the GPUs are
vertically mounted.
x4 are inside of the PSU Shroud.
x1 is on the PowerBoard behind the PSU.
Radiators 360mm x 60mm with x1 set of standard 25mm fans.
Or 360mm x 40mm with x2 sets of standard 25mm fans (Push/Pull).
Maximum GPU Length 500 mm
Maximum GPU Height 170 mm in standard orientation | Unlimited in vertical orientation

Spectre 3.0 Integra, Integra Umbra Limited Edition &
Integra Umbra Chrome Elite Limited Edition Assembly Manual
Revision 2.2
Page | 7
Maximum CPU Cooler Height
170 mm
Maximum PSU Length 220mm (Space allowed for cables inside of PSU shroud).
Front Panel I/O No Front I/O | Vandal Switch 16mm | White LED
Vertical GPU Mount
x2 with 3 slots (60mm) spacing. x1 is included. 2nd Vertical GPU Mount
Available Separately here.
Riser cable not included, compatible with Linkup PCIE 4.0 Riser Cables.
Materials 6061 Aluminum Anodized. Cast Acrylic | Stainless Steel | PCB
Manufacturing Process
CNC Mill, CNC Lathe, CNC Router, PCB.
Assembly
Distribution Plate Assembled by Hand. Metal Components need to be
assembled and attached to the distribution plate by the customer.
Testing/Validation All Distribution Plates are factory pressure tested and precise fastener tension
is applied.

Spectre 3.0 Integra, Integra Umbra Limited Edition &
Integra Umbra Chrome Elite Limited Edition Assembly Manual
Revision 2.2
Page | 8
Included Items
Items
Spectre 3.0
Integra
Integra Umbra
Limited Edition
Integra Umbra
Chrome Elite
Limited Edition
Spectre 3.0 Integra Case
1
1
1
Distribution Plate Integrated Components:
•Reservoir
1
1
1
•
Pump Top
1
1
1
•Pump Cover
1
1
1
PowerBoard Integrated Components:
•Core Component Cables:
o
24pin 1 1 1
o8pin PCIe
6
6
6
o8pin EPS
4
4
4
(As many inputs must be used as outputs.)
•
Hubs:
o
PWM 6 6 6
oARGB (Single input for each)
10
10
10
•
LEDs
oIntegrated ARGB 90-degree LEDs
20
20
20
oIntegrated UV 90-degree LEDs
15
15
15
•
Touch sensing Power Button 1 1 1
•Extra Power and Reset Buttons
1
1
1
Cables:
•PowerBoard Linking Cables Standard Set:
o
24pin 1 1 1
o8pin PCIe
3
3
3
o8Pin EPS
2
2
2
•18AWG Black Heatshrinkless Sleeve
1
1
1
Linking Cables & PSU Adaptors for motherboards with 90-
degree connectors available here.
•PWM Female to Female 50cm Black Sleeved
1
1
1
•
ARGB Female to Female 50cm Black Sleeved
1
1
1
Case Components:
•Distribution Plate
1
1
1
•
Clear Cast Acrylic Side Panel Window
1
1
1
•
Protium 2.0 ARGB D5 Cover 1 1 1
•Case Panel Set
23
23
23
•
Vertical GPU Mount
1
1
1
Accessories:
•Hex Keys
oM3
1
1
1
o
M4 1 1 1
oM6
1
1
1
•
Microfiber Cloth
1
1
1
•Stop Fittings
2
2
2
•5V ARGB LED Strip 50cm 2 3
(1x pre-installed)
3
(1x pre-installed)

Spectre 3.0 Integra, Integra Umbra Limited Edition &
Integra Umbra Chrome Elite Limited Edition Assembly Manual
Revision 2.2
Page | 9
Warranty
Spectre 3.0 Integra, Integra Umbra Limited Edition & Integra Umbra Chrome Elite Limited
Edition 2-Year Limited Warranty:
1: The Integrated Water-cooling system is pressure tested at the factory, there is no need to
adjust the fasteners on the distribution plate. Take care not to over tighten any of the fasteners
particularly on the acrylic, stop as soon as you feel feedback or tension on the fastener. On the
metal parts you can tighten normally. We are not responsible for damage caused by over-
tightening the fasteners.
2: Any thread stripping, cross threading or thread damage will not be covered under our warranty.
All threads are pre-tested. We use stainless steel fasteners which are extremely durable.
3: All acrylic is carefully checked for scratches, marks or particles as the manifold is assembled.
We are not responsible for mistreatment of the acrylic. Only clean with a microfiber cloth and use
nothing except distilled or deionized water for cleaning, or Novus Plastic Cleaner. Damage caused
by cleaning agents (particularly alcohols or solvents) is not covered under warranty.
4: Acrylic Surface Guarantee: Marks on acrylic which cannot be wiped away with a microfiber
cloth will only be covered under warranty under the following conditions: That they did not occur
after the item was shipped from the Singularity Computers Factory or Retailer. If there are more
than 5 marks which are beyond 5mm in length and visible when facing perpendicular to the
surface. Evidence of this must be photographed in detail and photographs must be taken
perpendicular to the surface. Marks must be easily visible in photographs.
5: For the latest coolant recommendations please visit http://bit.ly/sc-important-info. We are
not responsible for staining of the acrylic, but it has never been an issue with our products. Most
staining will be easy to remove by flushing out the loop with distilled water for 24hrs or using
Mayhems Blitz. If you are concerned about staining, then we suggest Mayhems Non-Stain Dyes.
6: Any damage which occurs after the item leaves the Singularity Computers Factory or our
Retailers is not covered under warranty. We are not responsible for shipping damage or
mishandling.

Spectre 3.0 Integra, Integra Umbra Limited Edition &
Integra Umbra Chrome Elite Limited Edition Assembly Manual
Revision 2.2
Page | 10
Table of Fasteners & Panels
Fasteners
Type Quantity Used in
Step(s)
Type Quantity Used in
Step(s)
M3x6mm
Phillips Head
9 Mounting
Motherboard
M4x35mm 2 8
M3x6mm 16 11 M4 Springwasher 12 4
M4x6mm 22 5, 7 M6x20mm 5 6, 8
M4x8mm 3 8 M6x30mm 6 6
M4x10mm 18 3, 4, 9 6-32 Thumbscrew 8
Mounting PCIe
Devices
M4x16mm 2 4 MB SO
M3-M4 x6x6 9
Mounting
Motherboard
Panels
M4x20mm 8 4, 7
Panels
Name Quantity Used in Step(s)
a
Strut
2
4
B
LED Cover Front 1 1, 2, 3, 4
C
Top Radiator Panel Support 2 4, 6, 7
D
Feet 2 4, 6
E
PSU Front Bracket
1
5, 8
F
PSU Rear Bracket 1 5, 8
G
PSU Bottom Panel 1 5, 8
H
PSU Shroud Mount 1 6, 8
I
Side Panel Window Bracket 2 5, 8
J
Radiator Panel 2 1, 3, 7, 8
K
PSU Top Panel 1 5, 8
L
Cable Shroud
1
8
M
PSU Side Panel 1 5, 8
N
Rear IO Support
1
8
O
LED Cover Top 1 1, 3
P
LED Diffuser
2
1, 3
q
Rear IO Panel 1 8

Spectre 3.0 Integra, Integra Umbra Limited Edition &
Integra Umbra Chrome Elite Limited Edition Assembly Manual
Revision 2.2
Page | 11
Vertical GPU Included list

Spectre 3.0 Integra, Integra Umbra Limited Edition &
Integra Umbra Chrome Elite Limited Edition Assembly Manual
Revision 2.2
Page | 12
Assembly Manual
Assembly Note
Spectre is built from thick and strong CNC Machined aluminum components with tight tolerances.
There is no flex in the metal parts like there is on other cases. Due to this we have had to build
tolerances into all the mounting holes on Spectre 3.0 Integra. If something does not align then
loosen all related fasteners on the surrounding panels to let the component settle in, then tighten
the fasteners again.
Step 1: Install ARGB 50cm LED Strips.
Pieces Involved
• 2x 50cm ARGB LED Strips
•oLed Cover Top
•BLED Cover Front •jRadiator Panels
Remove the adhesive covers on the LED strips and stick them onto the positions marked in the
diagrams below. Make sure to put the cables in the correct orientation for the best cable
management, which depends where you plan on connecting them in your build. There should be
one LED strip installed onto the inside of LED Cover Front, another installed inside of LED Cover
Top and another installed on the inside of the top Radiator Panel.
IMPORTANT
: All three LED Strips need to be cut to length to fit into position. If you plan on using
the individually LED Strip functions then you need to know how many LEDs are remaining on
each LED Strip after you cut them. When you cut them, count how many LEDs are
remaining on
each LED Strip and remember which header you will plug each one into. The
Spectre 3.0 Integra
LED Strips each have 30 LEDs before they are cut
.
Cut LED Strips on the sections marked in
the diagram below.

Spectre 3.0 Integra, Integra Umbra Limited Edition &
Integra Umbra Chrome Elite Limited Edition Assembly Manual
Revision 2.2
Page | 13
Step 2: Install Power Button.
Pieces Involved •BLED Cover Front •Power Button
Remove the Power Button retention ring and O-ring. Thread the cable through from the front of
the Front LED Cover until the Power Button is in position. Install the O-ring onto the Power Button
and then tighten the retention ring to hold it in position. The O-ring prevents the Power Button
from coming loose.

Spectre 3.0 Integra, Integra Umbra Limited Edition &
Integra Umbra Chrome Elite Limited Edition Assembly Manual
Revision 2.2
Page | 14
Step 3: Install LED Covers onto Radiator Panels.
Pieces Involved
•BLED Cover Front •PLED Diffuser
•oLed Cover Top •
Fasteners – 6x M4 x 10mm
•jRadiator Panels
Attach the Radiator Panels to the LED Covers with the LED Diffusors sandwiched in between. The
assembly for the top is slightly different to the front, the top needs x4 M4 x10mm fasteners but
the front only needs x2 M4 x 10mm fasteners. Do not over tighten fasteners on acrylic.

Spectre 3.0 Integra, Integra Umbra Limited Edition &
Integra Umbra Chrome Elite Limited Edition Assembly Manual
Revision 2.2
Page | 15
Step 4: Assemble Legs.
Pieces Involved
•a2x Struts •
Fasteners – 4x M4 x 10mm
•d2x Feet •
Fasteners – 4x M4 x 20mm
•c2x Top Radiator Panel Supports •
Fasteners – 2x M4 x 16mm
•Fasteners – 10x M4 Spring Washers
Attach the Feet to the Struts with 1x M4 x 14mm Fastener and 1x M4 Spring Washer per leg in the
middle hole and 2x M4 x 10mm + 2x M4 Spring Washers in the outer two holes per leg.
Attach the Top Radiator Panel Supports to the Struts with 2x M4 x 20mm and 2x M4 Spring
Washers per leg.

Spectre 3.0 Integra, Integra Umbra Limited Edition &
Integra Umbra Chrome Elite Limited Edition Assembly Manual
Revision 2.2
Page | 16
Step 5: Assemble PSU Shroud.
Pieces Involved
•fPSU Rear Bracket •gPSU Bottom Panel
•ePSU Front Bracket •i2x Side Panel Window Bracket
•kPSU Top Panel •
Fasteners – 16x M4 x 6mm
•mPSU Side Panel
Attach the PSU Top Panel, PSU Side Panel and PSU Bottom Panel to the PSU Rear Bracket and PSU
Front Bracket using the x16 M4 x 6mm Fasteners. Then attach the Side Panel Window Brackets to
the bottom of the PSU Shroud. Carefully review the diagram below for the orientation of all the
pieces. If you have any fastener alignment issues you will need to loosen related fasteners to
allow the built-in tolerances to settle everything into position.

Spectre 3.0 Integra, Integra Umbra Limited Edition &
Integra Umbra Chrome Elite Limited Edition Assembly Manual
Revision 2.2
Page | 17
Step 6: Install Legs onto Distribution Plate.
Pieces Involved
•Distribution plate
•Fasteners – 6x M6 x 30mm
•abcLegs •
Fasteners – 1x M6 x 20mm
•hPSU Shroud Mount
Lay the legs down so that the main Struts are horizontal with a solid flat surface such as a table,
and the Feet and Top Panel Supports are vertical. Space the legs so that they are aligned with the
mounting holes on the distribution plate, you will need to estimate this. Lay the distribution plate
on top of the Legs and move the legs and distribution plate until the holes line up (be careful not
to scratch the acrylic). Align one leg and install the fasteners then move onto the second leg. Do
not fully tighten the fasteners until all the fasteners are in the holes and the threads started.
Install the PSU Shroud Mount onto the lower left corner so that the Distribution Plate is
sandwiched in between the Leg and PSU Shroud Mount. Attach the distribution plate to the Legs
using the 6x M6 x 30mm Fasteners and in the top left corner use the 1x M6 x 20mm Fastener.

Spectre 3.0 Integra, Integra Umbra Limited Edition &
Integra Umbra Chrome Elite Limited Edition Assembly Manual
Revision 2.2
Page | 18
Step 7: Install Radiator Panels onto Legs.
Pieces Involved
•Spectre 3.0 Integra Case
•Fasteners – 6x M4 x 6mm
•bJp Radiator Panel Assembly Front •
Fasteners – 4x M4 x 20mm
•Jop Radiator Panel Assembly Top
Attach the Top Radiator Panel assembly to the Legs using 6x M4 x 6mm Fasteners. Attach the
Front Radiator Panel assembly to the front Leg using 4x M4 x 20mm Fasteners.
If you have any fastener alignment issues you will need to loosen related fasteners to allow the
built-in tolerances to settle everything into position.

Spectre 3.0 Integra, Integra Umbra Limited Edition &
Integra Umbra Chrome Elite Limited Edition Assembly Manual
Revision 2.2
Page | 19
Step 8: Install PSU Shroud, Cable Shroud & Rear IO.
Pieces Involved
• Spectre 3.0 Integra Case •nRear I/O Support
•fekmgi PSU Shroud •
Fasteners – 4x M6 x 20mm
•hPSU Shroud Mount •
Fasteners – 2x M4 x 14mm
•JRadiator Panels •
Fasteners – 3x M4 x 8mm
•lCable Shroud •
Fasteners – 2x M4 x 35mm
•qRear I/O Panel
PSU Shroud Installation:
Begin by installing the PSU Shroud to the PSU Shroud Mount with 2x M6 x 20mm Fasteners. Then
align the PSU Shroud to the Distribution Plate and install the two fasteners through the
Distribution Plate to hold the PSU Shroud at the front. If you have any fastener alignment issues
you will need to loosen related fasteners to allow the built-in tolerances to settle everything into
position. Do not over tighten fasteners on acrylic.
Cable Shroud Installation:
Install the Cable Shroud onto the Case. It fits onto the bottom of the Distribution Plate underneath
the D5 Pump Top. Use the 2x M4 x 14mm Fasteners to attach it, the fasteners install from the
back of the Distribution Plate. Do not over tighten fasteners on acrylic.
Rear IO Installation:
Install the Rear IO Support onto the case, it fits onto the front of the Distribution Plate and the
fasteners go all the way through from the back sandwiching everything together. Use the 2x M4
35mm fasteners with one M4 Spring Washer per fastener. Then install the Rear IO Panel, first
installing the 2x M4 8mm fasteners at the top which go into the Rear IO Support, then the M4
8mm fastener at the bottom which goes into the PSU Rear Bracket. If you have any fastener
alignment issues you will need to loosen related fasteners to allow the built-in tolerances to
settle everything into position. Do not over-tighten fasteners on acrylic.