Rosewill MAXCUBE User manual

2© All rights reserved by Rosewill
Diagram
Front I/O Pinout
USB 3.0 CONNECTOR USB 2.0 CONNECTOR HD Audio CONNECTOR
USB+5V
LP
LP+
GND
NC
USB+5V
LP
LP+
GND
NO PIN
AUD GND
PRESENCE#
SENSE1 RETURN
NO PIN
SENSE2 RETURN
PORT1L
PORT1R
PORT2R
SENSE SEND
PORT2L
NO PIN NO PIN
(components vary by country)
User Manual
CASE
Right Side Panel
Top Dust Filter
Left Side Panel
Bottom Dust Filter
Radiator Bracket
HDD Tray
Front Panel

3© All rights reserved by Rosewill
Front I/O
User Manual
CASE
Accessory Kit
USB 2.0
USB
to M/B
USB 2.0
USB
to M/B
USB 3.0
to M/B
USB 3.0
to M/B
Audio
HD AUDIO connector
to M/B
Part’s Name Qty Used forFigure
Motherboard tray,
HDD tray, power supply
Screw-A
HDD, ODDScrew-B
Cable Tie
2.5 inch HDDScrew-C
21
12
3
8
Cables, wires
Power Button
to M/B
POWER SW
Reset Button
to M/B
Reset SW

4© All rights reserved by Rosewill
Installation Guide
1-1. Untwist the thumbscrews and
slide out left and right side panels
(Figure 1).
2-1. Lay the chassis on its side so the
interior is accessible (Figure 2).
2-2. Seat the power supply unit (PSU) to
the bottom of the case and secure
with Screw-A (Figure 2).
1. Open the Unit
2. Install the Power Supply
User Manual
CASE
1
2

5© All rights reserved by Rosewill
3-1. Line up the standoffs with the screw
holes on the motherboard.
3-2. Screw the motherboard down with
Screw-A (Figure 3).
4-1. Loosen the screws on the panel cover,
and slide the panel open (Figure 4a).
4-2. Unscrew and remove the slot cover.
4-3. Install the add-in card and secure with
the screws (Figure 4b).
3. Install the Motherboard
4. Install the Add-in Card
User Manual
CASE
3
4a 4b

6© All rights reserved by Rosewill
5-3. Insert a 5.25” drive into the bay and secure with Screw-B (Figure 5b).
5-4. Replace the front panel back onto the case.
5-1. Pull the front panel out and remove it (Figure 1).
5-2. Unscrew the HDD dock and remove it. (Figure 5a).
5. Install the External 5.25” Device
User Manual
CASE
5a
5b

7© All rights reserved by Rosewill
User Manual
CASE
6-1. Screw the 2.5” SSD/HDD onto the tray with Screw-C (Figure 6a).
6-2. Install the 3.5” HDD onto the tray (secure with a screw if desired) (Figure 6b).
6-3. Insert the tray into the HDD cage or the top rail until the latch clicks into a secure position
(Figure 6c) (Figure 6d).
6. Install the 3.5”/2.5” HDD/SDD
6a
6c 6d
6b

8© All rights reserved by Rosewill
7-1. To prevent damage, it is
recommended to keep all panels
closed and secured.
Slide the side panels back into
place and secure shut with
thumbscrews (Figure 7a).
7-2. To prevent overheating and damage,
clean the dust filter regularly to
ensure adequate airflow (Figure 7b).
7. Care
User Manual
CASE
7a
7b

9© All rights reserved by Rosewill
8. Options
User Manual
CASE
8-1. Fan Install
The Max Cube has the capacity of installing additional fans:
2x120 mm fans under the top cover.
1x90 mm fan in the back.
8-2. Liquid Radiator Cooling
The Max Cube gives you the option of installing a 240 mm radiator to cool your system.
8-3. Front location installation (Figure 8a):
a. Remove the front panel.
b. Unscrew to remove the 230 mm fan.
c. Secure the radiator with screws and put the front panel back on.
8-4. Top location installation (Figure 8b):
a. Remove the top dust filter.
b. Secure the radiator with screws and put the dust filter back on.
8a
8b