Sintermask fabbster 11.1 User manual

Aufbauanleitung
Assembly instruction
Sicherheitshinweise auf den letzten Seiten beachten!
Note safety guidelines on the last pages!
READTHIS
FIRST!

1x clippers
5466
160x screw M5x30
5467
20x screw M3x6
1x allen key small
5472
4x distance piece
M5x50
1x allen key big
1x scraper
5473
160x nut M5
5458
12x ferrule
5461
4x deflection pulley
5459
2x pulley
5461
2x belt stopper
4x belt
5478
5471
2x screw
M5x60
6016
2x stabilization bracket 2x stabilization socket
6015 6018
1x gearbox adapter
1x hex pulley
6017 6063
4x end switch
6251
4x cassette cover
6074
3x rocker switch
6085
8x nut M3
6194
4x screw M5x45
parts
5471
2x screw
M5x70

5522
1x multipurpose
grease
5503
2x center gear
5505
2x planet carrier
5507
2x gear box
6278
1x connectordrive shaft
5504
6x planet gear
6279
1x platform sensor
5475
4x motor Nema 17
5477
11x radial bearing
5475
10x linear bearings
1x power cable
5501
1x fan
1x USB-cable
5877
1x BLU/R cable heating 670mm
5492
1x B/W cable temp. sensor 960mm 10x pipe bracket90°
6000
6194
8x screw M3x16
6069
1x B/R cable heating 670mm
5559
8x cover disk
6346
1x nozzle unit vers. II
6277
1x tube adaptor
6367
1x material sensor
6276
1x extruder cover
6068
1x B/W Temp sensor cable
760mm (platform)
Teileliste • partlist
parts

5457
30x cassette 6082
1x corrugated
pipe 300mm
6081
1x corrugated
pipe 350mm
5535
1x corrugated
pipe 520mm
5464
8x long frame rod
LIKE Sticks ABS
2x 100g
1x feeding tube
5846
5534
1x corrugated
pipe 360mm
5533
1x corrugated
pipe 280mm
5465
6x short slide rod
2x stick magazine
5768
5773
4x clamping bar
5715
1x platform carrier
5777
1x inlay
1x rubber hammer
5772
1x build platform
5780
1x e-box power supply
6031
1x thin transmission rod
5779
1x e-box boards
5493
1x B/R cable heating 860mm
parts
4x screw M5x40
5712

Schrauben nicht fixieren bis dieses Symbol auftaucht:
Davor nur mit 2,5-3 Umdrehungen ansetzen!
Do not fix the screws unless you see this symbol:
Until then just tighten the screws with 2,5-3 turns!
Vor jedem Schritt die Teile bereitlegen.
Preposition the parts before beginning each step.
Beim Zusammenbau sollte eine stabile Unterlage verwendet werden.
A stable base should be used for the assembly.
Bei Verwendung eines Akkuschraubers minimales Drehmoment einstellen, um
Beschädigungen zu vermeiden.
If you use an electric screw driver, set it to minimal torque to avoid damage.
Einige Teile sind ölig, entsprechende Kleidung wird empfohlen.
Some parts are oily, appropriate clothing is recommended.
GeneralInstructions
FIX

5475
2x motor Nema 17
5459
2x pulley
5457
2x cassette
5467
8x screw M3x6
parts needed in step :1

2x
1
~ 2mm
Push the motor on
a flat surface to
mount the pulley.
HINT:
Mind the cable
orientation!
2x
Z1

5522
2x multipurpose
grease
5504
6x planet gear
5503
2x center gear
5475
2x motor Nema 17
5507
2x gear box
5505
2x planet carrier
5467
8x screw M3x6
parts needed in step :2

2
1
2
3
Grease
Use the planet carrier as a tool
to push down the center gear.
HINT:
Rough side of planetary gears
facing planet carrier, smooth side
facing up!
2x
2x
Z2

3
Insert 8 nuts per cassette
12x
12x
Z3
If the nuts don’t clamp
use a piece of tape!
HINT:
5457
12x cassette
5473
96x nut M5

5477
2x radial bearing
5457
1x cassette
5475
3x linear bearings
5466
16x screw M5x30
5465
2x short slide rod
5461
1x deflection pulley
1x belt
5478
Z1
1x motor cassette
Z2
2x cassettes with nuts
parts needed in step :4

1
2
3
4

5477
2x radial bearing
5457
1x cassette
5475
7x linear bearings
5466
16x screw M5x30
5465
2x short slide rod
5461
1x deflection pulley
3x belt
5478
Z1
1x motor cassette
Z2
2x cassettes with nuts
parts needed in step :5

5
1
2
3
4

6
1FIX
Tension the belt!
Belts should
vibrate 2-3sec
when plucked
2
FIX
3
150N-200N
15kg-20kg

5477
2x radial bearing
5457
2x cassette
5466
2x screw M5x30
5473
2x nut M5
parts needed in step :7

7
A
B
A
B
A
B
0,5cm0,5cm
0,5cm
Caution: Screws only needed for
fabbster 11.1 - not for fabbsterG!

5477
3x radial bearing
5457
1x cassette
5466
16x screw M5x30
5461
1x deflection pulley
Z2
2x cassettes with nuts
1x hex pulley
6017
5464
1x long frame rod
5458
2x ferrule
parts needed in step :8
5465
1x short slide rod

8
A
A

5477
3x radial bearing
5457
1x cassette
5466
12x screw M5x30
Z2
2x cassettes with nuts
5464
1x long frame rod
5458
2x ferrule
6018
1x gearbox adapter
parts needed in step :9
5465
2x short slide rod
5461
1x deflection pulley