Siqura XSNet C4104SW User manual

1
V3
XSNet C4104SW/C4108SW
Quick Start Guide
This quick start guide describes how to install and use the Hardened Managed Ethernet Switch. This is the
switch of choice for harsh environments constrained by space.
Physical Description
The Port Status LEDs and Power Inputs
LED State Indication
10/100Base-TX, 100Base SFP
Steady A valid network connection
established.
LINK/ACT Flashing Transmitting or receiving data.
ACT stands forACTIVITY.
100 Steady
Connection at 100Mbps speed.
1000Base SFP
Steady A valid network connection
established.
LINK/ACT Flashing Transmitting or receiving data.
ACT stands forACTIVITY.
1000 Steady
Connection at 1000Mbps speed.
Power Input Assignment
Power3 12VDC DC Jack
＋12-48VDC
Power2 －Power Ground
＋12-48VDC
Power1 －Power Ground
Earth Ground
Terminal Block
Relay Output Rating 1A @ 24VDC
Relay Alarm Assignment
FAULT
*Warning signal disable for following:
1.The relay contact closes if Power1 and
Power2 are both failed but Power3 on.
2.The relay contact closes if Power3 is failed
but Power1 and Power2 are both on.
DC Terminal Block Power Inputs: There are three power inputs can be used to power up this switch.
Redundant power supplies function is supported.
Functional Description
Complies with EN50121-4 environmental requirements for railway applications.
Meets NEMA TS2 Environmental requirements such as temperature, shock, and vibration for
traffic control equipment.
Meets EN61000-6-2 & EN61000-6-4 EMC Generic Standard Immunity for industrial environment.
Manageable via SNMP, Web-based, Telnet, and RS-232 console port.
Supports Command Line Interface in RS-232 console.
Supports 802.3/802.3u/802.3ab/802.3z/802.3x. Auto-negotiation: 10/100/1000Mbps,
full/half-duplex. Auto MDI/MDIX.
The C4104SW is equipped with 2x 100Base-FX SFP slots.
The C4108SW is equipped with 2x 1000Base-FX SFP slots.
Support 8192 MAC addresses. Provides 2M bits memory buffer.
Alarms for power and port link failure by relay output.
Power Supply: Redundant DC Terminal Block power inputs or 12VDC DC JACK with 100-240VAC
external power supply.
Operating voltage and Max. current consumption: 0.92A @ 12VDC, 0.46A @ 24VDC, 0.23A @
48VDC. Power consumption: 11W Max.
-40°C to 75°C (-40°F to 167°F) operating temperature range. Tested for functional operation @
-40°C to 85°C (-40°F to 185°F).
Supports Din-Rail or Panel Mounting installation.
Console Configuration
Connect to the switch console:
Connect the DB9 straight cable to the RS-232 serial port of the device and the RS-232 serial port of
the terminal or computer running the terminal emulation application. Direct access to the
administration console is achieved by directly connecting a terminal or a PC equipped with a
terminal-emulation program (such as HyperTerminal) to the switch console port.
Configuration settings of the terminal-emulation program:
Baud rate: 115,200bps
Data bits: 8
Parity: none
Stop bit: 1
Flow control: none
Press the “Enter” key. The Command Line Interface (CLI) screen should appear as below:
Logon to Exec Mode (View Mode):
At the “switch_a login:”prompt just type in “root” and press <Enter> to logon to Exec Mode (or View
Mode). And the “switch_a>” prompt will show on the screen.

XSNet C4104SW/C4108SW
2 V3
Login the switch:
Specify the default IP address (192.168.1.10) of the switch in the web browser. A login window will be
shown as below:
Enter the factory default login ID: root.
Enter the factory default password (no password).
Then click on the “Login” button to log on to the switch.
Web Configuration
Set new IP address and subnet mask for Switch:
At the “switch_a(config)#” prompt just type in “interface vlan1.1” and press <Enter> to logon to vlan 1
(vlan1.1 means vlan 1). And the “switch_a(config-if)#” prompt will show on the screen.
Command Syntax: “ip address A.B.C.D/M”. “A.B.C.D” specifies IP address. “M” specifies IP subnet
mask. “M”= 8: 255.0.0.0, 16:255.255.0.0, or 24: 255.255.255.0.
For example, At the “switch_a(config-if)#” prompt just type in “ip address 192.168.1.10/24” and press
<Enter> to set new IP address (192.168.1.10) and new IP subnet mask (255.255.255.0) for Switch.
Logon to Configure Mode (Configure Terminal Mode):
At the “switch_a#” prompt just type in “configure terminal” and press <Enter> to logon to Configure
Mode (or Configure Terminal Mode). And the “switch_a(config)#” prompt will show on the screen.
Logon to Privileged Exec Mode (Enable Mode):
At the “switch_a>” prompt just type in “enable” and press <Enter> to logon to Privileged Exec Mode (or
Enable Mode). And the “switch_a#” prompt will show on the screen.