THOMSON SPEEDTOUCH 605S Safety guide

SpeedTouch™605s
Business SHDSL Router
Setup and User’s Guide
Release R4.2
600
SERIES

SpeedTouch™605s
Setup and User’s Guide
Release R4.2

Status v1.0
Change Note PeckelbeenS
Short Title Setup and User's Guide ST605s R4.2 (en)
Copyright © 2003 THOMSON. All rights reserved. Passing on, and copying of this document, use and
communication of its contents is not permitted without written authorization from
THOMSON. The content of this document is furnished for informational use only, may be
subject to change without notice, and should not be construed as a commitment by
THOMSON. THOMSON assumes no responsibility or liability for any errors or inaccuracies
that may appear in this document.

1
Contents
1 SpeedTouch™ Installation ............................................ 3
1.1 Getting Acquainted with the SpeedTouch™.................................................... 4
1.2 Setting up the SpeedTouch™............................................................................. 6
1.3 SpeedTouch™ Configuration Setup.................................................................. 7
1.3.1 Configuration Setup for Microsoft Windows Operating Systems ........................................ 8
1.3.2 Configuration Setup for other Operating Systems.................................................................14
1.4 Dr SpeedTouch™ Installation .......................................................................... 17
2 SpeedTouch™ Internet Connectivity ........................ 21
2.1 Surfing the Internet........................................................................................... 22
2.2 Connect to the Internet via SpeedTouch™’s embedded PPP client........... 23
2.2.1 Internet Sessions via Windows XP’s UPnP .............................................................................. 24
2.2.2 Internet Sessions via the SpeedTouch™ Web Pages (all OSs)............................................25
2.3 Connect to the Internet via a Broadband Dial-in Client ............................... 26
2.3.1 Using the Windows XP Dial-in Client....................................................................................... 27
2.3.2 Using the Mac OS X Dial-in Client.............................................................................................30
3 SpeedTouch™ Web Interface..................................... 31
3.1 Basic Topics Menu Links ................................................................................... 34
3.2 Advanced Topics Menu Links ........................................................................... 37

2
4 SpeedTouch™ NAPT Manager .................................. 51
5 SpeedTouch™ System Software Upgrade ................ 57
5.1 The SpeedTouch™ Upgrade Wizard .............................................................. 58
5.2 Manual System Software Management via BOOTP Server ......................... 62
6 Troubleshooting ........................................................... 65
6.1 General................................................................................................................ 66
6.2 SpeedTouch™ Default Configuration.............................................................. 67

1 SpeedTouch™ Installation
E-SIT-CTC-20030605-0003 v1.0 3
1 SpeedTouch™ Installation
Introduction Thank you for purchasing the SpeedTouch™605s Business SHDSL Router!
With the SpeedTouch™605s Business Symmetrical High speed Digital Subscriber Line
(SHDSL) Router, surfing the Internet will become a whole new experience.
In this Setup and User's
Guide
This User's Guide will assist you in getting acquainted with the SpeedTouch™605s Busi-
ness SHDSL Router and in getting connected quickly to the Internet.
Terminology Generally, the SpeedTouch™605s will be referred to as SpeedTouch™ in this Setup and
User's Guide unless specifically indicated.
Safety instructions Before connecting the SpeedTouch™, read the SpeedTouch™ Quick Installation Guide
and Safety Instructions.
UPnP The SpeedTouch™605s is a Universal Plug and Play (UPnP) certified product.
UPnP enables your computer to discover and control UPnP devices on the network.
Note For more information about how to install UPnP on your computer please
consult your operating system’s user’s guide.
Documentation and
software updates
The SpeedTouch™605s product continues to evolve as extra and new functionalities
are made available.
For more information on the latest technological innovations, software upgrades, and
documents, please visit the SpeedTouch™ web site at:
www.speedtouch.com

1 SpeedTouch™ Installation
E-SIT-CTC-20030605-0003 v1.0
4
1.1 Getting Acquainted with the SpeedTouch™
Introducing the
SpeedTouch™
Prior to proceeding, please make sure to read the SpeedTouch™Quick Installation
Guide first. It provides important package content and safety information.
Check whether all items are present in your package.
In the event of damaged or missing items, please contact your local product dealer for
further information.
Front and back panel
layout
The SpeedTouch™605s Business SHDSL Router is presented in a slim line housing:
The device is equipped with a single 10/100Base-T Half-/Full-duplex MDI-X Ethernet
port:
Front panel LEDs The SpeedTouch™605s Business SHDSL Router is equipped with five LEDs on its front
panel, indicating the state of the device during normal operation:
Power Switch
DSL
L
ine
P
ort
R
eset
Power Socket
10/100Base-T Ethernet port
Indicator Description
Name Color State
LAN Green Flashing Ethernet LAN activity
Off No Ethernet LAN activity
Line TX Green Flashing ATM cell transmission on DSL line
Off No transmission activity
Line RX Green Flashing ATM cell reception on DSL line
Off No reception activity
Line Sync Green Off No SHDSL line
Flashing Initialization of SHDSL line
On SHDSL line synchronized

1 SpeedTouch™ Installation
E-SIT-CTC-20030605-0003 v1.0 5
Ethernet port(s) LEDs The Ethernet port on the rear panel has one LED:
DSL Port
DSL service The appropriate SHDSL service must be available at your local premises.
PWR/Alarm Green Flashing Back-to-defaults
On Power on, normal operation
Orange On Self test
Red Flashing Power on
On Power on, selftest failed
Indicator Description
Name Color State
Indicator Name Color State Description
Integrity/Activity Green Off No connection on this port
On Ethernet link up. No activity
Flashing Activity on this Ethernet port
Link Integrity/Activity LED
10/100Base -T
Service Port pinning
2-wire SHDSL 3/4

1 SpeedTouch™ Installation
E-SIT-CTC-20030605-0003 v1.0
6
1.2 Setting up the SpeedTouch™
Local network For Ethernet connectivity you need at least:
•A computer with installed Ethernet Network Interface Card (NIC) or available
on-board Ethernet port
•If needed, a hub or switch and the necessary connection cables
Ethernet Cables In the SpeedTouch™605s box, a full wired Cat.5 straight-through RJ45/RJ45 Ethernet
cable, further referred to as LAN cable is included.
You can use LAN cables other than the one provided in the box. However make sure to
use correct connection cables.
Wiring procedure Proceed as follows:
1Use the included LAN cable to wire your computer's Ethernet port to the
SpeedTouch™605s Ethernet port.
2Use the included DSL cable to wire the SpeedTouch™605s's Line port to your
telephone wall outlet.
3Plug the power adapter's coaxial jack into the SpeedTouch™605s DC inlet and
plug the power adapter in a wall outlet.
Note Always check first whether the included power adapter suits the local
power specifications.
More information on
Ethernet wiring
For more information, see the application note “The SpeedTouch™ and Ethernet
Connectivity”.
PC wiring Once all connections are made, the result should look similar as below:

1 SpeedTouch™ Installation
E-SIT-CTC-20030605-0003 v1.0 7
1.3 SpeedTouch™ Configuration Setup
Internet connectivity Some configuration may be required to prepare the SpeedTouch™ for Internet connec-
tivity.
What you need from
your ISP
You might need a user account with an Internet Service Provider (ISP) for Internet
access. For this user account, your ISP will provide you with:
•A user name (logon ID)
•A password
Other information may be required, depending on the ISP's specific requirements.
Configuration of the
SpeedTouch™
Depending on your computer's Operating System (OS) the configuration of your
Internet connectivity can be done automatically or manually.
If your computer runs:
•AMicrosoft Windows OS.
The SpeedTouch™ Setup wizard, included on the SpeedTouch™ Setup CD-ROM,
will automatically guide you through the configuration of both the SpeedTouch™
and your PC for setting up the appropriate configuration.
Proceed with “1.3.1 Configuration Setup for Microsoft Windows Operating
Systems” on page 8.
•Another OS, e.g. Mac OS, Unix, Linux.
The SpeedTouch™ Embedded Easy Setup wizard, accessible from the Speed-
Touch™ web pages, will automatically guide you through the configuration of the
SpeedTouch™.
Proceed with “1.3.2 Configuration Setup for other Operating Systems” on
page 14.

1 SpeedTouch™ Installation
E-SIT-CTC-20030605-0003 v1.0
8
1.3.1 Configuration Setup for Microsoft Windows
Operating Systems
Microsoft Windows One of the following Windows operating systems must be installed on your PC(s):
•Windows 98
•Windows 98SE
•Windows ME
•Windows NT4.0 SP6
•Windows 2000
•Windows XP
You may need the Windows installation CD-ROM during installation.
The SpeedTouch™
Setup wizard
The SpeedTouch™ Setup wizard procedure consists of two major parts:
•The detection procedure
•The configuration procedure

1 SpeedTouch™ Installation
E-SIT-CTC-20030605-0003 v1.0 9
The detection
procedure
The detection procedure proceeds as follows:
1Insert the SpeedTouch™ Setup CD-ROM in your PC's CD-ROM drive. The
SpeedTouch™ CD Browser will start automatically.
Note If the SpeedTouch™ CD Browser window does not appear automati-
cally, open a Run window via Start > Run from the Start menu and
enter the following path: D:\Menu.exe, where D stands for the drive
letter of your CD-ROM drive.
2The Choose Language window prompts you to select a language:
Select the language of your choice and click OK.
3The SpeedTouch™ CD Browser appears:
Click Initial Setup.
4The Setup and Installation window appears:
To start the SpeedTouch™ Setup wizard, click Setup my SpeedTouch™.

1 SpeedTouch™ Installation
E-SIT-CTC-20030605-0003 v1.0
10
5The Welcome to the SpeedTouch™ Setup Wizard window appears:
Click Next to proceed.
6The Software License Agreement window appears:
You must accept before continuing. Therefor click Yes to accept.
Note If you have already accepted this License Agreement in a previous
configuration setup, this window will not be shown.
7The Setup wizard will continue to search for the SpeedTouch™ on the network.
The following window shows the detection progress:

1 SpeedTouch™ Installation
E-SIT-CTC-20030605-0003 v1.0 11
8The Setup wizard should find your SpeedTouch™ device on the local network.
This is indicated by the following window:
In case more than one SpeedTouch™ device is found, a listing is provided from
which you can select your SpeedTouch™.
Note If the Setup wizard does not find any SpeedTouch™ on the network an
error window pops up. In this case check:
•Whether the SpeedTouch™ is turned on and fully initialized.
•Whether your PC is correctly connected to the SpeedTouch™
and has a valid IP address (i.e. any IP address but 0.0.0.0).
•Whether no dedicated firewall device or router is placed
between your PC and the SpeedTouch™ and whether no
personal firewall software is running on your PC.
To repeat the search for the SpeedTouch™, click Back and proceed
with step 7of this procedure.
9To continue with the configuration of your SpeedTouch™ and your PC, proceed
with the configuration procedure described below.

1 SpeedTouch™ Installation
E-SIT-CTC-20030605-0003 v1.0
12
The configuration
procedure
The Configuration procedure proceeds as follows:
1Once the SpeedTouch™ Setup wizard has detected your SpeedTouch™ device,
you can proceed with the configuration procedure.
If more than one SpeedTouch™ device is listed, select the appropriate one.
Then, click Next to proceed.
Note If the SpeedTouch™ has been configured before, it may be protected
by a system password. You must provide user name and system pass-
word before you can view the device details or continue with the
configuration.
2You will be asked to choose between reconfiguring your SpeedTouch™ or chang-
ing your Local Area Network configuration.
Select Reconfigure the SpeedTouch™ and click Next.
3The following window invites you to select the appropriate connection profile for
your Internet connectivity:
Select the connection profile of your choice and click Next to continue.
Note If the Service Provider has included a separate disk with a dedicated
connection profile, click Have Disk to navigate to the location of the
appropriate connection template file.
4Subsequent screens will guide you through the configuration setup of both your
SpeedTouch™ and/or your PC. Follow the instructions and enter the required
information where needed. This information should be provided by your Service
Provider.
5In a final step all configurations will be applied to the SpeedTouch™ and your PC.
You can follow the configuration progress in following window:

1 SpeedTouch™ Installation
E-SIT-CTC-20030605-0003 v1.0 13
6The SpeedTouch™ Setup wizard will appear again to announce that the configura-
tion has been successful:
Click Finish to close the wizard.
Note In some cases, the SpeedTouch™ Setup wizard may ask you to restart
your computer.
Most configuration profiles will enable SpeedTouch™’s DHCP server - and a PC’s
Ethernet port is configured as DHCP client by default. Therefore, in most cases, no
additional configuration of your PCs must be done if you want to enable multiple PCs
on your local network for accessing the Internet via the SpeedTouch™.
To make sure that all PCs are configured as expected (DHCP or fixed IP addresses) you
can re-run the SpeedTouch™ Setup wizard on every PC and select the Change the LAN
configuration option.
For fixed IP configurations, or other advanced settings, please follow the instructions
provided by your ISP or network administrator.

1 SpeedTouch™ Installation
E-SIT-CTC-20030605-0003 v1.0
14
1.3.2 Configuration Setup for other Operating
Systems
Supported Systems As the SpeedTouch™ is OS-independent, this configuration setup can be used by any
computer system.
Note The following procedure may equally be used on MS Windows OSs.
TCP/IP Ensure that your operating system has a valid TCP/IP configuration.
Configure your computer with a static Net10 private IP address, e.g. 10.0.0.1. Ensure,
however, that you do NOT use the 10.0.0.138 IP address as this is the default IP address
of the SpeedTouch™.
To ensure that IP connectivity exists, you can ping the SpeedTouch™.
Procedure The configuration setup proceeds as follows:
1To ensure that the SpeedTouch™ is in its factory default state, reset the
SpeedTouch™ to the default configuration. See “6 Troubleshooting” on page 65.
2Open a web browser and browse to the SpeedTouch™'s default IP address
10.0.0.138. See “3 SpeedTouch™ Web Interface” on page 31 for more informa-
tion.
3As a result the SpeedTouch™ System Info web page appears.
Expand the Advanced Topics and click Easy Setup.
Note If the SpeedTouch™ is in factory defaults, the Easy Setup wizard will
appear automatically.
4The Welcome to the SpeedTouch™ Setup Wizard window appears:
Click Next to continue.

1 SpeedTouch™ Installation
E-SIT-CTC-20030605-0003 v1.0 15
5The following window invites you to select the appropriate connection profile for
your internet connectivity:
In the Service list, click the connection profile of your choice.
Note You can add services to the Services list by uploading templates.
See “ Templates” on page 48 for more information on uploading
templates.
6Subsequent screens guide you through the configuration setup of both your
SpeedTouch™ and/or your PC. Follow the instructions and enter the required
information where needed. This information should be provided by your Service
Provider.
7In a final step all configurations are applied to the SpeedTouch™:
8The SpeedTouch™ Setup Wizard appears again to announce that the
configuration has been successful:
Click Finish to close the wizard.

1 SpeedTouch™ Installation
E-SIT-CTC-20030605-0003 v1.0
16
9After the configuration is applied on the SpeedTouch™ some additional configura-
tion of your computer system may be necessary.
Note The required settings for your computer should be provided by your
Service Provider, if applicable.
10 To check whether the new configuration was successfully completed, you can
browse to the SpeedTouch™ and check its current status.