Sirio Antenne New Vector 4000 User manual

20
BCopyright SIRIO antenne - Technical Data are subjected to change - Printed in ITALY - Rev. 06/03/2009 - Cod. ID041, pag. 4/4
HI-QUALITY ANTENNAS MADE IN ITALY
MOUNTING INSTRUCTIONSMOUNTING INSTRUCTIONS
19
14
1310mm
17
Insert the top section with
the cage (21) at L3 (see
tuning table for
frequency) and lock it
using the M4x4 hexagon
socket set screw cup
point (22) and 2mm
hexagonal key (23).
Pull out the 5 sections of
telescopic aluminium
whip (24) and lock them
using the 3.9x9.5mm
phillips tapping screws
(25).
Æ
Insert the fully assembled
telescopic whip into the
second section of tube
(10) and lock they using
the 3.9x9.5mm phillips
tapping screws (25).
Æ
5
4
3
20
L3
22
23
25
24
24
10
28
7
8
26
9
27
21
25
25
24
19
7788
991010
1111 1212
UHF female connector
Finally mount the
antenna on the mast
using M6 washer (7), M6
spring lock washer (8),
M6 hexagonal nut (9),
steel bracket (26 & 27)
and M6x240mm U-bolt
(28).
Insert the aluminium tube
10x1400 (19) into the
assembled cone tubes
13x1400 (17). Pull out the
top tube for 1310 mm and lock
it using the 3.9x12.7mm
phillips tapping screws (14).
Æ
Æ
Æ
Mount the 4 pcs of the
aluminum ring (20) and
lock them using M5x16
hexagon head screw (3),
M5 washer (4) and M5
hexagonal nut (5).
HI-QUALITY ANTENNAS MADE IN ITALY
ID041, pag.1/4
NEW VECTOR 4000NEW VECTOR 4000
27...28.5 MHz CB & 10m band Base Station Antenna
3/4 lBase station antenna working on CB and 10m band.
Made of telescopic anti-corodal aluminium tubes. Its long and
robust whip allows perfect performances and very good
connections at long distances too.
DESCRIPTIONDESCRIPTION
SPECIFICATIONSSPECIFICATIONS
TECHNICAL DATA
Electrical Data
Type
Frequency range
Impedance
Radiation ( H-plane)
Polarization
Gain
Bandwidth @ SWR £ 2)
SWR @ res. freq.
Max Power
Feed system
Connector
Mechanical Data
Materials
Wind resistance
Length (approx.)
Weigth (approx.)
Mounting Mast
: 3/4 lCoaxial J-pole
: 27...28.5 MHz tunable
: 50 W
: 360°omnidirectional
: Vertical
: 2 dBd, 4.15 dBi
: ³1400 KHz (120 channel)
: £ 1.2
: 1000 Watts continuous
3000 Watts short time
: Gamma match
: UHF-female
: Aluminium, Steel, Brass, Nylon
: 130 Km/h
: 8480 mm
: 4700 gr
: Æ35-42 mm

12 14
13
ID041, pag.3/4
HI-QUALITY ANTENNAS MADE IN ITALY
MOUNTING INSTRUCTIONSMOUNTING INSTRUCTIONS
Mount the aluminium
bracket (1) at distance L1
from the top edge of
bottom aluminium ring
(see tuning table for
frequency). Verify the real
alignement to the bracket
(1) and the connector (2).
Lock the bracket using
M5x16
(3), M5 washer
(4) and M5 hexagonal nut
(5).
hexagon head
screws
L1
2
1
5
43
Mount the gamma match
(6) on the connector and
lock it using M6 washer (7),
M6 spring lock washer (8)
and M6 hexagonal nut (9).
6
7
8
9
L2
5
43
Pull out the aluminium
bar of gamma match at
distance L2 from the
plastic cap (see tuning
table for frequency) and
lock it with the aluminium
bracket (1) using M5x16
hexagon head screw (3),
M5 washer (4) and M5
hexagonal nut (5).
Insert the second section
on the aluminium tube (10)
into the first section tube
(2) and lock them using the
enclosed hose clamp (11).
10
11
Mount the plastic ring (12) on the
second aluminium tube (10) at
1340 mm from the bottom
aluminium ring. Insert the plastic
arms (13) and lock them using
the 3.9x12.7mm phillips
tapping screws (14). Lock the
plastic ring (12) using the M6x10
hexagon socket set screw cup
point (15) and 3mm hexagonal
key (16). Verify that the plastic
arms (13) are aligned with
bottom hole on aluminium ring.
Æ
to align
Mount the cone made of
aluminium tubes
13x1400 (17) on the
bottom aluminium ring
using M6x12 hexagon
head screws (18), M6
washer (7) and M6 spring
lock washers (8).
Æ
1340mm
17 x 4 pcs
18
78
to align
15
16
10
1122
3344
5566
2
Insert limit punching
1
ID041, pag.2/4
HI-QUALITY ANTENNAS MADE IN ITALY
Parts List
Description
aluminium bracket
Æ33.5x37x1400mm alu. tube with connector first section
M5x16 hexagon head screws
M5 washer
M5 hexagonal nuts
gamma match assembly
M6 washer
M6 spring lock washer
M6 hexagonal nuts
Æ30.5x33x1400mm alu. tube second section
Æ36-39mm hose clamp
Plastic fixing ring
Plastic arms
Æ 3.9x12.7 tapping screws
M6x10 hexagon socket set screw
3mm hexagonal key
Æ11x13x1400mm alu. tube (cone bottom side)
M6x12 hexagon head screws
Æ8x10x1400mm alu. tube (cone top side)
aluminium ring section
top section with cage
M4x4 hexagon socket set screw cup point
2mm hexagonal key
5 sections telescopic aluminium whip
Æ3.9x9.5 tapping screws
30x65mm steel “V” bracket
30x65mm steel “flat” bracket
M6x240mm U-bolt
Pos
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Q.ty
1
1
6
6
6
1
11
11
7
1
1
1
4
8
1
1
4
4
4
4
1
1
1
1
10
3
3
3
TUNING TABLETUNING TABLE
n. 1 tape rules (meter)
n. 1 screwdriver cross point
n. 1 10mm open key
n. 2 8mm open key
*For the best tuning, please adjust only the gamma match L2 with an
SWR-Meter, about indicated range.
Freq.
(MHz)
Ch.19 CB 27.185
27.5
28.0
10m band 28.5
L1
(mm)
930
890
870
840
630 640
620 630
623 633
618 628
¸
¸
¸
¸
L3
(mm)
730
640
440
300
Mounting needed tools:
REMARK: use a good coax cable like RG-8 or RG-213 as short as possible
to get the best performance and we recommend to mount your antenna as
far as possible from metall roofs, walls, power lines and other antennas.
L2*
(mm)