SIS biomorph ProPlus User manual

Ground Support Equipment (US) ltd., DBA biomorph, 11 Broadway, New York, NY 10004. 888 302 3375 fax: [phone] [email protected]
ProPlus electric bi-level desk
USER SIDE
USER SIDE
REAR SIDE
biomorph
®
ergonomic PACS furniture
IMPORTANT: Longer side of foot towards user
IMPORTANT: Longer side of foot towards user

Ground Support Equipment (US) Ltd. DBA biomorph, 11 Broadway, New York, NY 10004 888 302 3375 fax: [phone] [email protected]
cable chain (important: extend desktops to full
opposite heights to ensure that cables will travel w/o stress)
controller box.
(connections face front or rear
depending on model)
Neatlinks cable guide (if purchased)
IMPORTANT: OPERATION & TROUBLESHOOTING
1. Adjust up or down by pushing the up or down arrows.
2. When first assembled or when unplugged, always lower
the table to bottom, release then hold down for 10 seconds
to level surfaces and reset controllers.
3. To set height memory: choose height, press ‘S’ then ‘1,2,or3’.
To return to preset: press the chosen # (1,2,3) then hold up
or down button and table will stop at preset height.
4. Push button w/circular arrow to change from front to rear.
TROUBLESHOOTING: Check all connections and reset per #2.
biomorph
®
adjustable PACS furniture
ProPlus Table
Cable Management
Questions? call 888 302 3375
Run extra cable length through the CableCab.
Place plugstrip inside for connections.
Position with removable panel facing user.
controller box
for surfaces
cable tracks
use supplied cable guides
switch for
front / rear
surfaces
desk frame
CableCab
#1(leg cables)
#1(switch)
#2
#3
#4
cable chain
use supplied screws to attach CableCab
using pilot holes, centered on grommet hole
mounts for monitor arms
(if purchased)
CableCab
attach tops to frame with
supplied screws using
pilot holes
use pilot holes
to mount
cable chain

Description
The DP1C is equipped with display and memory and is compatible with CBD4 (Advanced, software
077402 ver. 1.66 or later). The DP1 is only available as a 1-channel version for operation of the parallel
channels up and down. The actual height of the desk is shown in the display. The display is of the LED type
with a yellow light and 10 mm high digits.
Normal operation:
To run the desk up or down, press the UP or DOWN button, and keep it pressed until the desk reaches the
desired height. The display will count up or down while running, and after stop it will continually show
the current height of the desk.
Changing between cm and inches:
Keep the S button pressed for approx. 4 sec. and the reading will change from the current setting. The
default setting depends on the type chosen.
Store a memory position:
When pressing the “store” button, the display will flash “S” for 3 sec. Within the 3 sec. press memory
button 1, 2 or 3. The display will acknowledge by showing S1, S2 or S3 for 1 sec. To abort a store
sequence, press the UP or DOWN button while the “S” is flashing, or wait the 3 sec. until the display
automatically returns to show the height of the desk.
Drive to a stored position:
Version with “GO-memory”
Press memory button 1, 2, or 3. The display will flash “GO1”, “GO2” or “GO3” for 3 sec. Within the 3
sec. press the UP or DOWN button and keep it pressed until the desk stops in the stored position. Both the
Up and the Down button will activate memory drive. Although e.g. the memory position is higher than
the actual height, it will drive upwards when you press the Down button. While running to a memory
position the display will show GO1, GO2 or GO3, and when it stops in the stored position, the height of
the desk will be shown. Releasing the UP or DOWN button will abort the memory drive. The display will
show the height of the desk.
Version with “standard memory”
Press memory button 1, 2, or 3 and the system will start driving to the wanted memory position. Keep the
button pressed until the position is reached. The display will show the actual height during the memory
run.
Adjust the display to show the correct height:
It may be necessary to adjust the display due to different thicknesses of desktops etc, when the DP is
delivered from the factory. The DP will show 68 cm or 24.5 inches (default setting) height of the desk. At
the same time press the “Store” button and step UP or DOWN, until the display shows the correct height.
Adjusting the light intensity of the LED display
Possible light settings are: 0 = off, 25 = 25%, 50 = 50%, 75 = 75%, 100 = 100%.
Adjustment procedure
Press the “1” button and at the same time either “desk up” or “desk down” this will adjust the light in-
Operation of the DP1C
The DP1C cannot be used on the CBD4 with mains cut-off.
11
Desk up
Desk down
Store memory
Memory 1
Memory 2
Memory 3
S
1
2
3

Error no. Description
E01 The desk has an unknown position and needs to be initialised.
E02 Overload upwards has occurred.
E03 Overload downwards has occurred.
E16 Illegal keys pressed.
12
tensity. Initial press will show the current setting. Keep the “1” button pressed during the whole sequence
while adjusting up or down. Keep a button pressed for more than 800 msec then the button will auto
repeat every 100 msec. Releasing all buttons stores the new setting.
Adjusting the light timeout
Possible light timeouts are: 0-15 sec and off
Adjustment procedure
Press the “3” button and at the same time either “desk up” or “desk down” - this will adjust the light
timeout. Initial press will show the current setting. Keep the “3” button pressed during the whole se-
quence while adjusting up or down. Keep a button pressed for more than 800 msec, then the button will
auto repeat every 100 msec. Releasing all buttons stores the new setting.
Errors
Below please find the possible errors that can be displayed. The errors will only be displayed when a but-
ton is pressed. The display blinks while showing the error. E16 overrules any other error as the detection is
registered only in the display and no message is sent to the control box.
Diagnostic errors
The CBD4 (version 1.86 or later) can send up to 6 different diagnostic error codes at the same time. The
diagnostic error codes will overrule error states (except E16). Diagnostic errors will only appear as long as
the button is pressed. The display will blink EXX and will toggle through the diagnostic errors and send
them to the LINBUS in the CBD. For detailed error description and codes, please see the appropriate CBD
software description.
(Only working with DP1C from production date 1 february 2006 and onwards)