SIVUATEK M1-65 Quick guide

Electric Tankless Water Heater
Installation and Instruction Manual
Model:M1-65
Congratulations on the outstanding choice, the SIVUATEK tankless water is one of
the best options at the market today, with optimal quality and advanced tech
application.It is highly recommanded that you should take time to go through this
instruction manual to get full understanding and safety tips prior to installation, so
as to avoid any risk of property damage or serious injury.
This manual should be left to he houseowner after installation, for further guideline
of maintenance and troubleshooting.

Outstanding Customer Service
Thanks for being a valued customer of SIVUATEK Appliances, we hope that you are
pleasant with the purchasing and the unit would make your life better as expected.
At SIVUATEK Appliances, we think highly of product quality and its excellent
profermance, so all units are fully covered with 2-year warranty, against
manufacturing defect. You are always welcome to reach out for warranty clainment or
technical support, especially when:
(1) you get damaged pack or defect unit;
(2) you get question about installation and use of the unit;
(3) the unit gets unexpected issue when working.
We promise you that all messages to the service
will be replied within hours with professional and outstanding service,100% pleasant
shopping experience with SIVUATEK is what we strive for.
customer service
[e-mail]

Setting:86-131°F

9.17"(233mm)
6.22"(158mm)
2.09"(53mm)
6.3"(160mm)
10.51"(267mm)
1.57"(40mm)
Led Display
Hot Water Outlrt
Strain Relief
Control Key
Front Cover
Cold Water Inlet

M1-65
68 110
3.For the best warm experience, the M1-65 water heater is suggested for
a single faucet at a time.If you live in Southern US with warmer climate,
you could expect a shower.
M1-65 6.5
10.51"x9.17"x2.09"
0.5GPM/1.93L/min
78°F
58°F
42°F
35°F
32°F
27°F
4.5Ibs
M1-65
6.5KW
30AMP
27A
10AWG
240V~
2.9PSI-120PSI
1/2"NPT
0.5GPM
0.7GPM
1.0GPM
1.2GPM
1.3GPM
1.5GPM

Power wires with Grounding gets into the terminal blocks located right bottom of the
unit. A set of 10AWG/2 wires with Grounding wire should run from a 30A double pole
breaker on the home main breaker panel, to the water heater unit terminal blocks.
Securely tightened to get 240V supply.
The unit should be installed vertically on a flat surface that is larger than the unit itself.
Drill 4 holes into the wall for mounting screws,in accordance with the installation
template.Make sure the unit is securely mounted by those 4 wall anchor and screws
provided. Keep the unit away from any slashing or leaking water, also strong magnetic
field.
1.
2.
3.
4.
3

Before Installation Process

6.3"(160mm)
1.57"(40mm)
Accessories contents
4 screw
st4.2x30
4 espansion
boltes
1 installtion
template
TOOLS/MATERIALS REQUIRED
(not include)
Measuring tape Safety gloves Phillips
screwdriver
Electric drill Pencil Slotted
screwdriver
INSTALLATION INSTRUCTIONS
1.Figure out where to mount the water heater unit,
mark 4 mounting holes on the wall according to
the installation template(Fig.1).
2.Drill holes(Ø6x32mm) into the wall on those
4 marked position , put espansion bolt into the
mounting hole and then fix the 2 mounting brackets
with screws and Phillips screw driver
(Fig.2andFig.3).
3. The water heater gets 2 mounting brackets on the
back side, so all you need to do is hang the water
heater on those fixed brackets on wall, pull the
water heater unit downside to sit it tight(Fig.4).
Fig.1
Fig.4
Mounting Hole Mounting Hook
Espansion
boltes
Screw
Fig.2
Fig.3
Fig.2

Plumbing Installation
A set of service valves should be applied to the inlet and outlet fittings of the water
heater M1-65 if you live in hard water area, so you could get easy access of annual
maintenance. Also, a descale device should be applied to the inlet pipe, soas to
avoid scale build up and ensure long lifespan(Fig.5).
9. As with all high power appliances, make sure that you have turned off the vary
circuit breaker for the water heater before installing, disassembling or repairing
the water heater.Failure to follow this instruction may result in serious property
damage, injury or death and this will avoid your warranty.
M1-65
M1-65 310

.
Fig.5
Fig.6
Service Valve
Water Inlet
Descaling device
Water
Outlet
M1-65 water heater
Circuit Breaker Box
30A 240V
Ground Bar
L1 L2

L1
L2
E
control
panel
Leakage
Induction Coil
voltage
changer
Thermostat
Heating
Etement
Triac
Water Flow meter
Inlet TEMP Sensor
Outlet TEMP Sensor
Circuit Diagram

6.Fahrenheit/Celsius Switch- The default setting of the unit is Fahrenheit, if you
need to switch to Celsius, please shut off water flow to enter standby state, then
touch and hold the " " button, the setting will change in about 5 seconds.
Fahrenheit display Celsius display

3.If you live in hard water area and you get a descale device installed prior to the tankless
water heater, it is recommanded that you should annually change the filter for the descale
device, or do it according to the instrcution of its manufacturer.
F0 No water flow is detected.
A. Turn on faucet when water hot is
needed.
B. Contact SIVUATEK service for
maintenance instruction.
.

Quantity
1
1
1
1
Installation mounting
template
Number Product Name Unit
1
2
3
4
The water heater
Mounting brackets and
screws
Mounal and warranty
card
pc
pc
pc
set

240V or not
Exposed
to freezing
temp or not
SIVUATEK CUSTOMER SATIFACTION DEPARTMENT
Charge
or not

[e-mail]