skeye. HW 90240 User manual
www.skeye.com
Quick Start Guide
skeye.dart
HW 90240
Display
Views and Functions
Loudspeaker
Stylus
Locking
mechanism
Storage
battery
Reset key
Charging
contacts
DC 1-Wire GND
Power supply
unit
port
System
interface Headset
port Imager/Camera
pane
Loudspeaker LEDs Imager/Camera
ESC key
Standby
(press about 5 s)
Contact:
Höft & Wessel AG
Skeye
Rotenburger Str. 20
30659 Hannover
Tel. +49 511 6102-0
Fax. +49 511 6102-411
Mail. [email protected]
Web. www.skeye.de
Serviceline. +49 1803 232829
(0.09 EUR per min. within Germany)
Microphone
Show/Hide
touch /
keypad field
Scan key
Start button
Scan key
ENTER key
Cursor keys
Scan key
Version 1.2
Activate Backup Battery
Lower edge
Upper edge (display)
Backup battery switch – on
In the battery
compartment, push the
switch of the backup
battery () towards the
display using the stylus.
The backup battery is
on.
Note: Prior to initial operation, the storage battery should be completely
charged. To do so, place the device into the docking station.
Insert the storage battery with its noses at the rounded part into the
relevant recesses inside the battery compartment. Press the battery until
it audibly engages.
Insert Battery
Switch on Device
To switch on the device, use the middle, round key.
ON key
Data synchronisation
Call HWImagerTool to test the scanner function:
Start ⇒Programs ⇒Utilities ⇒HWImagerTool
HWImagerTool executes in the background and can be identified by
the SysTray symbol.
Calmly and angularly hold the skeye.dart in the direction of the
barcode to be scanned. A peep indicates that the entry of the barcode
has been successful. The gap should amount to about 5-10 cm.
An aid to orientation could be the skeye.dart lettering: aim with the
red dot.
HWImagerTool can be used to scan into any text field
(e.g. WordPad).
Scan of barcodes
Insert SIM card*
Remove the battery.
Push the locking of the card holder down.
Swing open the cover of the card holder.
Carefully insert the SIM card.
The conical corner should be top left, the
contacts of the SIM card should rest on the
contacts of the board.
Only slightly insert the SIM card into the
holder. If you push it too far into the holder
the hinges of the holder might block.
Push the locking upwards, thus locking
card holder incl. inserted card.
1. Prerequisite: a SIM card is inserted.
2. Switch the device on.
3. Please check if the GPRS module is switched on:
Start ⇒Settings ⇒Control Panel ⇒GSM-Control
4. After start of the operation system, your are asked the PIN
of the SIM card. Enter the number given by your provider.
5. When demanded you then enter the APN (Access Point Name)
of your provider.
6. As soon as the GSM symbol below
in the Systray is active (green)
(might take some minutes),
doubletip the symbol and select
"Connect“ in the window.
7. The GPRS connection is established.
Starting a GPRS connection*
You can start GPS with a terminal program of your own choice by
piloting the GPS module via COM6 with 9600 baud.
GPS-module*
These programs are available for free via
www.Microsoft.com/getstarted. With this program you can handle the
following tasks:
adding and removing programs on the skeye.dart
synchronisation of files
transfer and copying of files
Install on your PC the program for data synchronisation of a PC
with a mobile device. This program should be appropriate to your
operational system.
Microsoft ActiveSync V. 4.5 ⇒for Windows XP
Windows Mobile Device Center V. 6.1 ⇒for Windows Vista
Windows Mobile Device Center V. 6.1 ⇒for Windows 7
*only available in the skeye.dart FFE version
Other skeye. PDA manuals
