SKF Lincoln 91023 Instruction Manual

User and maintenance instructions
Models 91023 and 91029
Light and power cord reels*
Date of issue January 2018
Form number 404226
Version 2* Indicates change.

NOTE
Emphasizes useful hints and
recommendations as well as information for
efficient and trouble-free operation.
CAUTION
Indicates a dangerous situation that can lead
to light personal injury or property damage if
precautionary measures are ignored.
WARNING
Indicates a dangerous situation that could
lead to death or serious injury if
precautionary measures are ignored.
DANGER
Indicates a dangerous situation that will lead
to death or serious injury if precautionary
measures are ignored.
Explanation of signal
words for safety
Contents
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Explanation of signal words
for safety . . . . . . . . . . . . . . . . . . . . . . . . . 2
Table or bench mount
installation. . . . . . . . . . . . . . . . . . . . . . . 3
Wall mount installation . . . . . . . . . . . . 3
Ceiling mount installation . . . . . . . . . . 3
Operating instructions . . . . . . . . . . . . . 4
Electrical rating. . . . . . . . . . . . . . . . . . . 5
Maintenance . . . . . . . . . . . . . . . . . . . . . 6
Service parts. . . . . . . . . . . . . . . . . . . . . . 6
Warranty . . . . . . . . . . . . . . . . . . . . . . . . 8
Safety
Read and carefully observe these operating
instructions before unpacking and operating
equipment. Equipment must be operated,
maintained and repaired exclusively by
persons familiar with operating instructions.
Local safety regulations regarding
installation, operation and maintenance
must be followed.
Operate equipment only after safety
instructions and this service manual are
fully understood.
2

Table or bench
mount installation
1 Select a dry location within 2ft (609,8 mm)
of 120 V AC electrical outlet.
2 Mount bracket (†Fig. 1) directly onto
table or bench.
3 Line up mounting bracket with holes on
reel light unit and insert 8 in (203 mm)
pin (†Fig. 2).
4 Secure 8 in (203 mm) pin with
cotter pin (†Fig. 2).
5 Adjust ball stop (†Fig. 3)so light head
hangs at desired length.
6 Plug power cord into standard 120 V AC
electrical outlet.
Wall mount
installation
1 Select dry location within 2 ft (609,8 mm)
of 120 V AC electrical outlet.
2 Mount bracket to nearest available wood
stud or sturdy wall material using
appropriate screw fasteners (†Fig. 1),
leaving at least 24 in (609.8 mm) between
reel and edge of any wall or door frame.
Ceiling mount
installation
1 Select dry location within 2 ft (609,8 mm)
of 120 V AC electrical outlet.
2 Mount bracket directly into closest ceiling
joist or beam reinforced ceiling
beam († Fig. 1).
3 Insert reel into bracket. Use care to line up
the mounting holes († Fig. 2).
4 Secure 8 in (203 mm) pin with
cotter pin († Fig. 2).
5 Adjust ball stop († Fig. 3) so light head
hangs at desired length.
6 Plug power cord into standard 120 V AC
electrical outlet.
3 Line up mounting bracket with holes on
reel light unit and insert 8 in (203 mm)
pin († Fig. 2).
4 Secure 8 in (203 mm) pin with cotter pin
(†Fig. 2).
5 Adjust ball stop (†Fig. 3) so light head
hangs at desired length.
6 Plug power cord into standard 120 V AC
electrical outlet.
NOTE
Do not mount reel to any wall material
(including drywall and paneling) that cannot
support significant torsion or drag.
NOTE
Do not mount reel to drywall or any
unsupported ceiling material that cannot
support significant torsion or drag.
Fig. 1
Fig. 2
Fig. 3
3

WARNING
To avoid serious injury or death from
electrical shock or fire:
• Do not handle unit or plug it in with hands
that are wet or damp, while standing on a
wet or damp surface, or in water.
• This fixture must always be used in
accordance with all electrical and safety
codes and ordinances, including National
Electric Code (NEC) and
Occupational Safety and Health Act
(OSHA) codes on general industry
standards and interpretations.
• Always ensure that the power source
conforms to the requirements listed on the
unit.
• Always disconnect unit from its power
source before servicing or disassembling.
• This unit is only for use with
110 to 125 V AC-rated products, and is
equipped with an approved 3-conductor
cord with a 3-prong grounded plug.
• To reduce the risk of electrical shock, unit
should only be plugged into a properly
grounded 3-prong outlet.
• Unit is not waterproof and is not
intended for use in showers, saunas, or
potentially wet locations. Keep unit away
from sinks, tubs, showers, etc. Do not
attempt to retrieve unit if it falls into water
if it is still plugged into a power source.
Fatal electrocution could result.
• Do not remove the 3rd prong or
modify the plug in any way. Improper
connection of the grounding
conductor can result in electrical shock.
• Do not plug the unit into a non-grounded
outlet or extension cord.
If an extension cord is used, ensure the
cord is in good electrical condition and is a
minimum of 16 gauge, 3 conductor.
• This fixture is intended for use as a general
indoor power source. Do not use in
potentially dangerous locations, such as
flammable or explosive surroundings.
WARNING
Failure to comply with instructions and safety
information could result in electrical shock,
fire hazard or malfunction of unit.
Operating
instructions
1 Fully extend and lock cord in place
2 before using.
3 To lock, pull cord to desired length.
Slowly let cord retract back into reel until
click is heard.
4 To retract cord, pull cord out until reel
begins resisting. Guide cord into reel while
it is retracting. Hold onto cord until it
retracts completely into reel.
5 To lock multi-angle bracket into place,
pull looped spring loaded pin out, set reel
to desired angle and release looped
spring pin.
CAUTION
Do not release cord while it is retracting back
into reel.
Failure to do so may result in personal
injury and/or damage to the reel.
CAUTION
• Do not overload circuit. Check amperage
rating before connecting anything to
outlet(s) on product to be sure that circuit
will not be overloaded. Amperage rating of
reel can be found on label of reel. If circuit
breaker trips, unplug all devices and reset
circuit breaker. Double check amperage
rating of device before plugging it back in.
• Do not service reel light while it is plugged
in. This could cause electrical shock.
• Opening reel may cause injury, as reel
houses clock spring under high pressure.
4

Electrical rating
This product is protected by a circuit breaker:
that will cut off current if overloaded. In the
event of an overload, disconnect unit from
source of overload, wait for two minutes, and
press the circuit breaker reset button located
on the side of the unit. If circuit breaker con-
tinues to trip, unplug unit and discontinue
use.
WARNING
Do not overload. Check amperages of tools or
appliances to be used before proceeding with
use of fixture. Listed below is the maximum
amperage rating for unit.
Failure to comply may result in death or
serious injury.
CAUTION
Do not allow cord to fly unrestricted back
into reel.
Failure to comply may result in light
personal injury or damage to equipment.
Electrical rating
Part no. Length Cable type/gauge Maximum rating Lux Lumen
91023 50 ft (15,244 m) SJTOW 18/2 125 V AC >200 >600
91029 50 ft (15,244 m) SJTOW 14/3 125 V AC/12 A
5

Maintenance
To keep light reel operating smoothly:
1 Remove dirt and grime from reel case
using soft, damp cloth. Mild soap may be
used if needed. Do not get electrical plug
wet, and never immerse any part of unit in
solution to clean. Do not use any types of
solvents to clean unit.
2 To ensure smooth retraction, keep cord
clean by pulling cord to full length and
allow it to slowly retract through
dampened rag. Then pull cord out again to
full length again and allow to retract
through clean rag sprinkled with
talcum powder.
Service parts
Part number Description
410015 Replacement COB light for 91023
6

This page left intentionally blank.
7

skf.com | lincolnindustrial.com
® SKF and Lincoln are registered trademarks of the SKF Group.
© SKF Group 2018
The contents of this publication are the copyright of the publisher and may not be reproduced (even
extracts) unless prior written permission is granted. Every care has been taken to ensure the accuracy
of the information contained in this publication but no liability can be accepted for any loss or damage
whether direct, indirect or consequential arising out of the use of the information contained herein.
January 2018 · Form 404226 Version 2
Warranty
The instructions do not contain any information on the warranty.
This can be found in the General Conditions of Sales, available at:
www.lincolnindustrial.com/technicalservice or
www.skf.com/lubrication.