SkiTuning BASEMAN Installation instructions
BASEMAN
Original operating manual
Version 1.1
E
2
Table of content
1. Foreword .................................................................................. 3
1.1. Intended Use........................................................................3
2. Overview ..................................................................................4
3. General.....................................................................................5
4. Preparaon...............................................................................5
5. Calibrate the dial gauge.............................................................6
6. Measuring................................................................................. 6
7. Technicalspecicaons .............................................................7
3
1. Foreword
Before inial startup of the BASEMAN device this operang manual must be read by the operang perso-
nel and those responsible for maintenance. It complements the training manuals. Damage or injuries cau-
sed by ignoring the content menoned in these manuals will not assure warranty. The operator is obliged
by law to keep the accident regulaons in mind, which are regulated within the operator’s country/state.
Addionally the operaon manual is to be kept condenal and can only be accessible for authorized
personel. A transfer to third pares can only be done if approved in wring by VSLN SkiTuning GmbH.
All documents are protected in terms of copyright. Distribuon and duplicaon of the documents, also
parally, as well as exploitaon and communicaon of the content remains prohibited unless approved in
wring by VSLN SkiTuning GmbH. Violaon is punishable and require compensaon. All rights reserved by
VSLN SkiTuning GmbH.
1.1. Intended Use
The device is assembled exclusively for common Ski-service-maintenance (intended use). All further use
is dened non-intended use. The manufacturer is not legally responsible for damage/injuries resulng
from further use. Such risk is taken by the operator only. Intended use also includes compliance with
regulaons for operaon and maintenance prescribed by the manufacturer. Relevant accident preven-
on regulaons and other generally recognized safety-related regulaons and occupaonal medical rules
must be followed. The manufacturer is not legally responsible for damage/injuries resulng from arbitrary
changes. We are giving our best at all me to improve our products and we reserve the right to apply all
changes and improvements which we consider expedient. However there is no obligaon to extend this
to devices previously delivered.
All gures, dimensions and weights in the operang instrucons are non-binding.
Original operaon-manual
© Copyright 2020 by
VSLN SkiTuning GmbH | Fornacherstraße 25 A-4890 Frankenmarkt | AUSTRIA
Tel: +43 677 – 630 807 96
E-Mail: o[email protected]
Autor: Alexander Vecchiato
1
2
3
4
5
6
12
13
14
7
9 8
10
11
4
1.
2. Overview
Nr Beschreibung
1Display
2USB interface (not needed)
3Zero buon
4LED- Lamp
5Lamp holder - fastening screws
6Lamp holder
7Straightedge
8Straightedge - marking
9Straightedge - fastening screws
10 Calliper
11 Angle of support
12 Adjusng nut
13 ON/OFF buon
14 mm/inch buon
Abb.1
!
1
2
3
5
3. General
The boom edge angle (picture 2) denes how aggressive and direct the ski / snowboard will respond.
The smaller the angle the more aggressive and direct the response.
0,6° to 1,0°
- for racing
- personal tuning on event on skis
1,0° to 2,0°
- universal for regular skiing on the slope
- commercial Skis have 1,0° to 1,5°
- freerider and powder skis have 1,5° to 2,0°
In order to work correctly on the boom edge the actual amount of degrees of the boom edge must be
known. The BASEMAN measures the boom edge angle precisely to 0,01 degrees.
IMPORTAINT: Material which has been already removed cannot be undone anymore. For
instance, if material is grinded to 1.5 degrees, one cannot anymore grind back to 1.0 degrees
(the material is no longer available).
This can only be corrected by levelling of the ski/snowboard via machine.
4. Preparaon
1. Remove baery safety foil
2. Loosen the allen screw with the allen key (included in the delivery), picture.3.1
3. Insert the lamp holder and x it with allen key, picture.3.3
4. Insert LED- lamp …
5. … and check funconality through clockwise turning, picture.3.2
picture 2
picture 3
6
5. Calibrate the dial gauge
1. Switch on the dial gauge
2. Put the BASEMAN on a straight surface, adjust the support angle upwards with the adjusng
nut (straightedge fully lies upon) ATTENTION: the straitedge has to bear on the surface picture 4
3. Adjust the dial gauge on mm with the “mm/inch”-buon
4. Set the dial gauge to zero with the “Zero”-buon
6. Measuring
1. Switch on the LED-lamp.Put the BASEMAN on a straight surface, adjust the support angle up-
wards with the adjusng nut (straightedge fully lies upon), picture 4
2. Set the BASEMAN in a 90 degree angle to the boom angle upon the base
3. Posion the straightedge-marking between the base and the edge, picture 6
4. Gently push the straightedge with the index nger and thumb. With outward rotaon of the
adjusng nut…
5. … set the angle of support and stop rotang the adjusng nut when no light shines through.
Picture 7
6. Read the boom edge angle from the dial gauge (1mm = 1 degree)
picture 4
picture 5
90°
picture 6picture 7
7
7. Technical specicaons
Type Baseman
weight 288 g
ambient temperature limit 0 to 40°C
humidity < 80%
accuracy 0,01 mm
dialgaugebaery 1x Lithium Baery CR2032
LED-lampbaery 3x Lithium Baery LR41
Table of contents
