Skoda Fabia II 2007 Instruction manual

Workshop Manual
FABIA II 2007 ➤
Automatic 6-speed gearbox 09G
Edition 05.07
Service
Service Department. Technical Information


List of Workshop Manual Repair GroupsList of Workshop Manual
Repair GroupsList of Workshop Manual Repair Groups
Repair Group
00 - Technical data
32 - Torque converter
37 - Control, housing
38 - Wheels, Control
39 - Final drive, differential gear
Service


Contents
00 - Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1 Technical Data for the Gearbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1 Identification of the gearbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.2 Identification characters, aggregate assignment, ratios . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.3 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2 Information and repair instructions for the automatic gearbox 09G . . . . . . . . . . . . . . . . . . 3
2.1 Information for the automatic gearbox 09G . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.2 Repair instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.3 Explanation of the terms used in this workshop manual . . . . . . . . . . . . . . . . . . . . . . . . . . 5
32 - Torque converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1 Torque converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.1 Torque converter identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.2 Draining the torque converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.3 Removing and installing gasket ring for torque converter . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.4 Checking the torque converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.5 Installing the torque converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
37 - Control, housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1 Electric/Electronic components and fitting locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.1 Electric/Electronic components and fitting locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.2 Removing and installing automatic gearbox control unit J217 . . . . . . . . . . . . . . . . . . . . . . 16
1.3 Removing and installing selector lever lock solenoid N110 . . . . . . . . . . . . . . . . . . . . . . . . 17
2 Repairing shift mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2.1 Inspecting the gearshift mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2.2 Inspecting and adjusting the selector lever control cable . . . . . . . . . . . . . . . . . . . . . . . . . . 23
2.3 Dismantling and assembling the gearshift mechanism - Summary of components . . . . . . 24
2.4 Removing and Installing the cover for the shift mechanism . . . . . . . . . . . . . . . . . . . . . . . . 26
2.5 Removing and installing shift mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
2.6 Removing and installing the selector lever control cable . . . . . . . . . . . . . . . . . . . . . . . . . . 30
2.7 Removing and installing the Tiptronic switch F189 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
2.8 Checking the plug connections at the gearshift mechanism . . . . . . . . . . . . . . . . . . . . . . . . 34
3 Removing and installing the gearbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
3.1 Removing the gearbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
3.2 Installing the gearbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
3.3 Transporting an automatic gearbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
4 Inspecting ATF level and if necessary topping up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
4.1 Inspecting ATF level and if necessary topping up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
4.2 Change ATF or top up after repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
5 Removing and installing ATF radiator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
5.1 ATF radiator - Overview of components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
5.2 Removing and installing ATF radiator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
38 - Wheels, Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
1 Removing and installing oil pan, oil filter, slide valve body and internal wiring looms . . . . 51
1.1 Oil pan, oil filter, slide valve body, internal wiring looms - Overview of components . . . . . . 52
1.2 Removing and installing oil pan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
1.3 Removing and installing the oil filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
1.4 Removing and installing the slide valve body . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
1.5 removing and installing wiring loom with 14-pin plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
1.6 Removing and installing wiring loom with 8-pin plug and integrated gearbox oil temperature
sender G93 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
FABIA II 2007 ➤
Automatic 6-speed gearbox 09G - Edition 05.07
Contents i


1.7 Removing and installing the gearbox input r.p.m. sender G182 . . . . . . . . . . . . . . . . . . . . 72
1.8 Removing and installing the gearbox output r.p.m. sender G195 . . . . . . . . . . . . . . . . . . . . 73
2 Removing, installing and setting multi-function switch F125 . . . . . . . . . . . . . . . . . . . . . . . . 75
2.1 Removing and installing the multi-function switch F125 . . . . . . . . . . . . . . . . . . . . . . . . . . 75
2.2 Setting multi-function switch F125 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
39 - Final drive, differential gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
1 Replace the flange shaft gasket rings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
1.1 Replacing the left flange shaft gasket ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
1.2 Replacing the right flange shaft seal ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
2 Replacing the gasket ring for the gearshift shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
2.1 Replacing the gasket ring for the gearshift shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
FABIA II 2007 ➤
Automatic 6-speed gearbox 09G - Edition 05.07
ii Contents


00 – Technical data
1 Technical Data for the Gearbox
1.1 Identification of the gearbox
The “Automatic 6-speed gearbox 09G” is installed in combination
with 4-cylinder engines. Assignment ⇒ page 1 .
Location of identification code letters on the gearbox
Identification characters and manufacturing data of the gearbox
-arrow 1- and -arrow 2-.
Example:
FXA Gearbox identification characters
02H2T0014
4Serial number
02 : production year 2002
H : production month from A = January to M =
December
2T : identification of the gearbox from the manu‐
facturer, 2T = 09G
00144 : serial number for the production month,
this is the 144th gearbox for the month of August
09G 300
035G Part number
AISIN AW Manufacturer: AISIN
Note
The gearbox identification characters also appear on the vehicle
data stickers.
1.2 Identification characters, aggregate assignment, ratios
Automatic gearbox 6-speed gearbox 09G
Identification characters JUF KGG
Manufac‐
tured from through 05.07 05.08 06.08 07.10
Assignment Engine 1.6 ltr./77 kW
Torque con‐
verter Identification characters QAAA
Ratio 1st gear 4,148
2nd gear 2,370
3rd gear 1,556
4th gear 1,155
5th gear 0,859
6th gear 0,686
Reverse gear 3,394
Intermediate
gear Input gear 48
Output gear 53
Ratio 0,906
FABIA II 2007 ➤
Automatic 6-speed gearbox 09G - Edition 05.07
1. Technical Data for the Gearbox 1


Automatic gearbox 6-speed gearbox 09G
Final drive Drive pinion 15
Crown wheel 61
Ratio 4,067
Automatic gearbox 6-speed gearbox 09G
Identification characters MFZ
Manufac‐
tured from through 07.10
Assignment Engine 1.6 ltr./77 kW
Torque con‐
verter Identification characters QAHA
Ratio 1st gear 4,148
2nd gear 2,370
3rd gear 1,556
4th gear 1,155
5th gear 0,859
6th gear 0,686
Reverse gear 3,394
Intermediate
gear Input gear 48
Output gear 53
Ratio 0,906
Final drive Drive pinion 15
Crown wheel 61
Ratio 4,067
1.3 Contents
Planetary gear
Contents Automatic gearbox 09G
New filling 6,0 - 6,1l
Top-up approx. 4.0 - 4.5 ltr 1)
Lubricant ⇒ Electronic Catalogue of Original
Parts
1) Filled for life: change the oil following repairs only.
Only ATF should be used as lubricant in the automatic gearbox
09G ⇒ Electronic Catalogue of Original Parts .
Checking ATF level, change ATF if necessary ⇒ page 43 .
FABIA II 2007 ➤
Automatic 6-speed gearbox 09G - Edition 05.07
2 Rep. Gr.00 - Technical data


2 Information and repair instructions for
the automatic gearbox 09G
2.1 Information for the automatic gearbox
09G
Gearbox
The automatic 6 speed gearbox 09G is equipped with 6 hydraul‐
ically controlled forward gears. When the lockup clutch is closed,
these forward gears become mechanically driven gears by by‐
passing the converter slip.
Torque converter
The torque converter is equipped with a torque converter lockup
clutch. The closing of the lockup clutch is load and speed sensi‐
tive, and particularly low in vibrations, and without the converter
slip the lockup clutch drives all forward gears mechanically.
ATF
The ATF is filled for life. The ATF need not be changed within the
scope of servicing.
The ATF oil filling is for the planetary gear and final drive together.
Check and top up ⇒ page 43 .
♦ Only ATF available as spare part should be used in the auto‐
matic gearbox 09G. Other oils can lead to functional problems
or to failure of the gearbox, ATF spare part number ⇒ Elec‐
tronic catalogue of original parts .
Gear-change points change on upward and downward gradients
On upward or downward gradients, gear-changes are selected
automatically by additional gear-change mapping, according to
accelerator position and driving speed.
♦ On steep gradients, gear-change mapping is adapted to en‐
gine power output
♦ On steep gradients, gear-change mapping is adapted to the
braking effect of the engine.
♦ By directly selecting a gear via the Tiptronic, e.g. for a slope
during trailer operation, the motor braking effect is also fully
used.
2.2 Repair instructions
Scrupulous care and cleanliness as well as the proper tools are
essential requirements for carrying out proper and successful
gearbox repairs. Obviously, the generally valid basic safety rules
apply to repair work.
A number of generally valid notes for individual repair operations
- which are otherwise listed several times at numerous points in
the workshop manual - are summarized here. They apply to this
workshop manual.
Special tools
List of the special tools used in the workshop manual ⇒ Workshop
Equipment Electronic Catalogue .
Gearbox
♦ Each time a gearbox is installed, basic settings are required.
FABIA II 2007 ➤
Automatic 6-speed gearbox 09G - Edition 05.07
2. Information and repair instructions for the automatic gearbox 09G 3


♦ Do not run the engine or tow the vehicle when the oil pan of
the gearbox has been removed or without ATF filling.
♦ If the automatic gearbox is replaced, check ATF level if nec‐
essary top up with ATF ⇒ page 43 . Capacity and specifica‐
tion ⇒ page 2 .
♦ Secure the torque converter against dropping out when the
gearbox is removed.
♦ Thoroughly clean the connection points and their surroundings
before releasing.
♦ Before installing the gearbox check the fitting position of the
torque converter ⇒ page 9 .
♦ When installing, take care with the correct positions of dowel
sleeves in the engine.
♦ Place removed parts on a clean surface and cover. Use foil
and paper. Do not use fuzzy cloths!
♦ Carefully cover or close opened components if the repair is not
completed immediately.
♦ Only install clean parts. Remove spare parts from their wrap‐
ping immediately before fitting.
FABIA II 2007 ➤
Automatic 6-speed gearbox 09G - Edition 05.07
4 Rep. Gr.00 - Technical data


O-rings, gasket rings, gaskets
♦ Always replace O-rings, gaskets and gasket rings.
♦ After removing gaskets, examine the contact surface in the
housing or on shafts for burrs or damage, and correct if nec‐
essary.
♦ Depending on location, before fitting a gasket ring, smear the
outer surface and sealing lip thinly with ATF or axle oil.
♦ Before inserting the O-rings coat with ATF to prevent the rings
being squashed during installation.
♦ The open side of the sealing rings is turned towards the oil.
♦ Never use other lubricants in the ATF area.
♦ Radial shaft seals - before mounting lightly oil at outside di‐
ameter and fill half the space between the sealing lips
-arrow- with sealing grease - G 052 128 A1- .
♦ After installation, inspect ATF level and if necessary top up
⇒ page 43 .
Locking elements
♦ Do not over-extend the circlips, if necessary replace.
♦ Circlips must be positioned in the base of the groove.
Screws, nuts
♦ Slacken and tighten nuts and bolts for attaching covers and
housings diagonally across.
♦ Do not twist particularly sensitive parts - e.g. the slide valve
body - and slacken and tighten diagonally across in stages.
♦ Tightening torques apply for non-oiled nuts and bolts.
♦ Clean the thread of the screws that are inserted with a locking
agent with a wire brush. Insert bolts with locking agent -AMV
185 101 A1- .
♦ Clean all threaded holes into which self-locking bolts are in‐
serted, using a thread tap to remove locking agent residues.
Otherwise there is a risk that the bolts will shear at the next
disassembling.
♦ Replace the self-locking screws and nuts.
♦ Bolts that need to be turned at a certain angle after tightening
must always be replaced.
Targeted fault-finding
Before repairing the automatic gearbox 09G, try to determine the
origin of the damage as accurately as possible using the ⇒ Vehi‐
cle diagnosis, testing and information system VAS 5051 in the
“Targeted fault-finding” mode.
2.3 Explanation of the terms used in this
workshop manual
The following explanations are only related to this assembly: Au‐
tomatic gearbox 09G. They do not claim to be valid in all cases.
ATF (Automatic Transmission Fluid)
Gear oil for automatic gearbox.
ATF level
ATF level in the gearbox. To measure the ATF level, see the in‐
structions in the Workshop Repairs Manual.
FABIA II 2007 ➤
Automatic 6-speed gearbox 09G - Edition 05.07
2. Information and repair instructions for the automatic gearbox 09G 5


Brakes
They hold together the rotating components in the gearbox. As
opposed to the clutches the brakes are supported on the gearbox
housing.
Torque converter
Transfers the engine torque to the automatic gearbox and serves
as a hydraulic starting clutch. The torque converter also includes
the torque converter lockup clutch.
Self-diagnosis
The capability of the control unit for the automatic gearbox
-J217-:
♦ recognize faults,
♦ react to faults,
♦ store faults,
♦ Determine measured values and to display them in the meas‐
ured value block.
Perform self-diagnosis
– Connect ⇒ Vehicle diagnosis, testing and information system
VAS 5051 and perform “Targeted Fault Finding” or “Vehicle
self-diagnosis”.
Clutches
In combination with the brakes, the clutches switch between the
various forward and reverse gears of the planetary gears, thus
providing different forward gear ratios.
Wiring
Fitting locations of electrical cables and components in the gear‐
box.
Selector lever lock solenoid -N110-
Located in the gearshift mechanism close to the selector lever.
Prevents the (unintentional) shifting of the selector lever from po‐
sitions “P” and “N”, as long as the brake pedal is not pressed.
Solenoid valves
Open and shut the oil lines to the clutches and brakes.
Multi-function switch -F125-
The multi-function switch -F125- is screwed onto the top of the
gearbox housing to the gearshift shaft. It is an electrical switch,
which transfers the individual gears selected with the selector
lever to the gearbox control unit. It must be correctly set
⇒ page 77 .
Parking position
When the vehicle is parked, the selector lever locks the parking
gear in position “P” thereby preventing the vehicle from moving
off (unintentionally).
Planetary gear
The mechanical part of the automatic gearbox that is switched via
clutches and brakes without power flow interruption.
Slide valve body
Located below the gearbox and is surrounded by the oil pan of
the gearbox. Its valves regulate the hydraulic pressure and dis‐
FABIA II 2007 ➤
Automatic 6-speed gearbox 09G - Edition 05.07
6 Rep. Gr.00 - Technical data


tribute it via the oil galleries to the gearshift elements (clutches
and brakes).
Automatic gearbox control unit -J217-
Control unit -J217- determines the shifting points. The function of
the gearbox is monitored via self-diagnosis. If components or
sensors fail, an emergency running programme is activated to
continuity of vehicle operation.
Torque converter lockup clutch
Mechanically transmits the engine torque to the gearbox.
FABIA II 2007 ➤
Automatic 6-speed gearbox 09G - Edition 05.07
2. Information and repair instructions for the automatic gearbox 09G 7


32 – Torque converter
1 Torque converter
Note
♦
Repair instructions ⇒ page 3 .
♦ Coat gasket rings with ATF. Other types of lubricant will cause
the gearbox hydraulic control system to malfunction.
1.1 Torque converter identification
There are different torque converters. Identification occurs with
identification characters -arrow-.
Assignment torque converter ⇒ page 1 .
Torque converter identification
(Gearbox installed)
1.2 Draining the torque converter
Special tools and workshop equipment required
♦ Oil aspirator unit -(z. B. V.A.G 1782) -
If the ATF has been contaminated or if the gearbox has had a
major repair, the torque converter should be drained as follows:
– Drain off the ATF from the torque converter using an oil aspi‐
ration unit -V.A.G 1782- .
1.3 Removing and installing gasket ring for
torque converter
Special tools and workshop equipment required
♦ Ejection lever -MP3-418 (VW 681)-
♦ Thrust piece -T10175-
FABIA II 2007 ➤
Automatic 6-speed gearbox 09G - Edition 05.07
8 Rep. Gr.32 - Torque converter


Removing gasket ring for torque converter
– Lever out gasket ring with ejection lever -MP3-418 (VW 681)- .
Install gasket ring for torque converter
– Insert the gasket ring for the torque converter using a pressure
plate - T10175- .
1.4 Checking the torque converter
– Check hub -arrow- of torque converter for traces of wear.
Note
The torque converter is welded and must be replaced completely
if damaged or faults.
1.5 Installing the torque converter
Special tools and workshop equipment required
♦ Depth gauge
Work procedure
– Push the torque converter hub through the gasket ring up to
the first stop on the input shaft.
– Press the torque converter by hand into the converter housing
and turn it until the torque converter hub catches in the re‐
cesses of the inner gear of the ATF pump. The torque con‐
verter must be felt to slide in.
FABIA II 2007 ➤
Automatic 6-speed gearbox 09G - Edition 05.07
1. Torque converter 9


– Measure the dimension -a- between the screw-on flange of the
gearbox housing and the contact surface of the threaded
bores of the torque converter using a depth gauge.
• The converter is correctly installed if the dimension -a- is at
least 19.5 mm.
– Absolutely ensure that the dimension -a- is maintained during
further assembly. The torque converter must not slide to the
front.
WARNING
If the converter is installed wrongly the driver of the torque
converter or the ATF pump will be destroyed when the gearbox
on the engine is connected at its flange.
When subsequently installing the gearbox, the following point
must be observed.
WARNING
Always check before and after tightening up the screws on the
flange of the engine/gearbox whether the torque converter be‐
hind the driver plate can be turned. In cases where the torque
converter cannot be turned one must assume that it is not
properly installed and that either the driver plate of the torque
converter or the ATF pump will be destroyed during final tight‐
ening of the bolted connections.
FABIA II 2007 ➤
Automatic 6-speed gearbox 09G - Edition 05.07
10 Rep. Gr.32 - Torque converter


37 – Control, housing
1 Electric/Electronic components and
fitting locations
1.1 Electric/Electronic components and fitting locations
1 - Automatic gearbox control
unit -J217-
❑ Fitting location and re‐
moving and installing
⇒ page 16
❑ Control unit is checked
by self-diagnosis
2 - Diagnostic connection
❑ Fitting location: Cover in
driver's footwell
⇒ page 12
3 - Selector lever lock solenoid
-N110-
❑ Fitting location
⇒ page 13
❑ removing and installing
⇒ page 17
❑ is checked by self-diag‐
nosis
4 - Slide valve body
❑ Fitting location
⇒ page 13
❑ removing and installing
⇒ page 58
❑ Marking of solenoid
valves ⇒ page 55
5 - Wiring loom with 8-pin plug
and integrated gearbox oil
temperature sender -G93-
❑ Fitting location: Wiring
loom is fixed to the slide
valve body ⇒ page 13
❑ Gearbox oil tempera‐
ture sender -G93- is
checked by self-diagnosis
❑ removing and installing ⇒ page 71
6 - Wiring loom with 14-pin plug
❑ for solenoid valves and gearbox sensors
❑ Fitting location: Wiring loom is fixed to the slide valve body ⇒ page 13
❑ Identification of solenoid valves and wiring loom routing ⇒ page 55
❑ removing and installing ⇒ page 69
7 - Multi-function switch -F125-
❑ Fitting location ⇒ page 14
❑ is checked by self-diagnosis
❑ removing and installing ⇒ page 75
FABIA II 2007 ➤
Automatic 6-speed gearbox 09G - Edition 05.07
1. Electric/Electronic components and fitting locations 11


8 - Cover for shift mechanism
❑ removing and installing ⇒ page 26
❑ the Tiptronic switch -F189- ist integrated in the shift mechanism; Fitting location ⇒ page 14
9 - Relay for starter interlock switch
❑ Fitting location ⇒ Electrical System ⇒ Rep. Gr. 97
10 - Gearbox input r.p.m. sender -G182-
❑ Fitting location ⇒ page 15
❑ is checked by self-diagnosis
❑ removing and installing ⇒ page 72
11 - Gearbox output r.p.m. sender -G195-
❑ measures the gearbox output speed
❑ Fitting location ⇒ page 15
❑ is checked by self-diagnosis
❑ removing and installing ⇒ page 73
12 - Selector lever position indicator -Y6-
❑ Fitting location ⇒ page 15
❑ a switched off gear display points to an emergency operation with deactivated gearbox control unit
❑ a fully lit gear display points to an emergency operation with activated gearbox control unit
❑ removing and installing ⇒ Electrical System ⇒ Rep. Gr. 90
13 - Kick-down switch -F8-
❑Fitting location ⇒ page 16
❑ is checked by self-diagnosis
❑ Signal transfer from engine to gearbox control unit via CAN databus
❑ removing and installing accelerator pedal module ⇒ Engine ⇒ Rep. Gr. 20
14 - Brake light switch -F-
❑Fitting location ⇒ page 16
❑ Signal transfer from engine to gearbox control unit via CAN databus
❑ is checked by self-diagnosis
❑ removing and installing ⇒ Chassis ⇒ Rep. Gr. 46
Diagnostic connection
Fitting location: Cover in driver's footwell
FABIA II 2007 ➤
Automatic 6-speed gearbox 09G - Edition 05.07
12 Rep. Gr.37 - Control, housing


Selector lever lock solenoid -N110-
Fitting location: Selector lever lock solenoid -N110- -A- is located
in the gearshift mechanism
Slide valve body
Fitting location: The slide valve body is bolted to the bottom of the
gearbox housing and covered with the gearbox oil pan.
Wiring loom with 8-pin plug and integrated gearbox oil tempera‐
ture sender -G93- -Arrow-
Fitting location: Wiring loom is fixed to the slide valve body
Wiring loom with 14-pin plug
Fitting location: Wiring loom is fixed to the slide valve body
FABIA II 2007 ➤
Automatic 6-speed gearbox 09G - Edition 05.07
1. Electric/Electronic components and fitting locations 13


Multi-function switch -F125-
Fitting location: The multi-function switch is located at the top of
the gearbox. The plug connection -5- is directly placed onto the
multi-function switch.
Switch for Tiptronic -F189-
Fitting location: The Tiptronic switch -F189- is integrated into the
circuit board -A- of the gearshift mechanism.
The Tiptronic switch -F189- is installed firmly in the gearshift
mechanism and cannot be replaced individually. The removal and
installation procedure is only possible together with the gearshift
mechanism ⇒ page 27 .
FABIA II 2007 ➤
Automatic 6-speed gearbox 09G - Edition 05.07
14 Rep. Gr.37 - Control, housing


Gearbox output r.p.m. sender -G195-
Fitting location: The gearbox output r.p.m sender - G195-
-arrow 2- is fixed to the gearbox housing behind the slide valve
body.
Gearbox input r.p.m. sender -G182-
Fitting location: The gearbox input r.p.m sender -G182-
-arrow 1- is fixed to the gearbox housing behind the slide valve
body.
Selector lever position indicator -Y6-
Fitting location: Integrated in the dash panel insert.
Note
The selector lever position indicator -Y6- can only be replaced
together with the dash panel insert.
FABIA II 2007 ➤
Automatic 6-speed gearbox 09G - Edition 05.07
1. Electric/Electronic components and fitting locations 15


Kick-down switch -F8-
Brake light switch -F-
Fitting location: The brake light switch -F- -arrow- is located in the
foot controls.
Note
The switch may only be installed once to ensure that it has an
adequately tight fit.
1.2 Removing and installing automatic gear‐
box control unit -J217-
Fitting location: The control unit is located at the battery cover.
Removing the control unit
WARNING
Observe measures when disconnecting and connecting the
battery ⇒ Electrical System ⇒ Rep. Gr. 27 .
– Disconnect the battery-earth strap with the ignition off ⇒ Elec‐
trical System ⇒ Rep. Gr. 27 .
– Unlock the plug connection from the gearbox control unit and
disconnect.
FABIA II 2007 ➤
Automatic 6-speed gearbox 09G - Edition 05.07
16 Rep. Gr.37 - Control, housing
