SKUTCH CK-1A2 User manual

Music On Hold, Message On Hold & Commercials On Hold by TelephoneOnHold.com
"Telecommunication Products to solve Telecommunication Problems"
CK-1A2 Promotion-On-Hold Adapter
(For AT&T E2562
Introduction
Thank you for purchasing the Skutch CK-1A2 Promotion-
On-Hold Adapter for the AT&T E2562 two-line cordless
phone system. The CK-1A2 is a true plug and play
device. The unit does not require any "Learning" to
operate. When a call is placed ON HOLD from the base
set, or any one of the cordless phones, the caller will hear
the music on hold audio. When the line is re-answered,
the audio automatically stops. It's that simple!
Installation
1- Turn the phone upside down and connect the short modular cable from the CK-1A2 box to the
AT&T E2562 telephone jack that is labeled “LINE 1/ L1+L2”. (See Fig. 1).
Sensor Board
Sensor Cable
Power Cube
Audio Cord
For CD Players ONLY!
Fig. 1
Fig. 2

Music On Hold, Message On Hold & Commercials On Hold by TelephoneOnHold.com
2- Set the phone on the CK-1A2 box as shown in Figure#2.
3- Connect the audio cord from your music on hold audio source, to the AUDIO IN jack
on the back of the CK-1 box. For DIGITAL units use the cable that comes with the
player, not ours.
To Telephone Lines
ToMusicOnHoldAudioSource
4- Connect a MOD cord from Telephone Wall Jack 1&2 to [1&2 Line on CK-1A2],
as shown in Fig. #3.
5- Locate the CK-1A2 “SENSOR BOARD", peel off the protector paper fromthe
Fig. #3
Alignment
(Center asshown)
Fig.4

Music On Hold, Message On Hold & Commercials On Hold by TelephoneOnHold.com
bottom of the sensor board, and carefully place it OVER the LINE 1 and LINE 2 indicator LEDS on the
AT&T base set as shown in Fig. #4. Make sure the holes in the back of the Sensor Board are directly over
the lights above the button.
6- Connect the Sensor Cable to the Sensor Board as shown in Fig. #4. Make sure thatthe “Down” sticker
on the “Flat Cable” connector facesdown.
7- Connect the POWER CUBE from the CK-1 box to 115VAC power. That'sit!
Testing the System:
1- Pickup line 1 on your telephone. The No."1" LED on the CK-1A2 SensorBoard should light up.
Hang up.
2- Repeat this test for line 2. If both lines light up when picked up, the CK-1A2 is working
properly. If either light does not light up,then
a) Make sure that the CK-1A2 and Telephone is connected topower.
b) Make sure that the SENSOR BOARD is alignedproperly.
Lights on CK-1 Box.
When you place a line on HOLD, the corresponding LED on the rear of the CK-1A2 box lights up to
confirm the music on hold condition.
Using Other models of telephones
The CK-1A2 will ONLY provide music on hold audio when a call is placed ON HOLD from the AT&T
E2562 base or any of its cordless telephones. Other models of telephones can be used with the AT&T
E2562, but the music on hold audio will not be played to calls placed ON HOLD from these telephones.
Tech Support - 916-786-6186
If you have any problems getting the unit to work properly feel free to give us a call. Technical Support is
available between the hours of 7:30 AM and 4:30 PM Pacific Time, Monday through Friday.
• ONE YEAR LIMITEDWARRANTY
This SKUTCH PRODUCT is warranted against defects for a period of one (1) year from the date of the original invoice.
Within this period, we will repair it without charge for parts and labor. To obtain warranty service the product must be
returned, at the customer's expense, to SKUTCH Electronics along with a copy of the original invoice. After the unit has
been repaired, SKUTCH will ship the PRODUCT back via UPS GROUND service at our expense. If any other form of
return shipment is requested, the customer will pay for 100% of the shipping cost.
This Warranty does not apply if in the sole opinion of SKUTCH Electronics, the PRODUCT has been damaged by
lightning or any other Acts of God, or by accident, misuse, neglect, or improper packing, shipping, modification or
servicing by other than an authorized SKUTCH Service Center.

Music On Hold, Message On Hold & Commercials On Hold by TelephoneOnHold.com
EXCEPT AS SPECIFICALLY PROVIDED IN THIS AGREEMENT, THERE ARE NO OTHER WARRANTIES,
EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OR
MERCHANTABILITIES OR FITNESS FOR A PARTICULAR PURPOSE AND IN NO EVENT SHALL SKUTCH
ELECTRONICS BE LIABLE FOR LOSS OF PROFITS OR BENEFITS, INDIRECT, SPECIAL, CONSEQUENTIAL OR
OTHER SIMILAR DAMAGES ARISING OUT OF ANY BREACH OF THIS WARRANTY OR OTHERWISE.
ACTA Statement
This equipment complies with Part 68 of FCC rules and the requirements adopted by
ACTA. On the bottom side of this equipment is a label that contains, among other information,
a product identifier in the format US: AAAEQ##TXXXX. If requested, this number must be
provided to the telephone company.
A plug and jack used to connect this equipment to the premises wiring and telephone network
must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A
compliant telephone cord and modular plug is provided with this product. It is designed to be connected
to a compatible modular jack that is also compliant. See installation instructions fordetails.
The REN is used to determine the number of devices that may be connected to a
telephone line. Excessive RENs on a telephone line may result in the devices not ringing in
response to an incoming call. In most but not all areas, the sum of RENs should not exceed
five (5.0). To be certain of the number of devices that may be connected to a line, as
determined by the total RENs, contact the local telephone company. For products approved
after July 23, 2001, the REN for this product is part of the product identifier that has the format
US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g.,
03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.
If this equipment causes harm to the telephone network, the telephone company will
notify you in advance that temporary discontinuance of service may be required. But if
advance notice isn't practical, the telephone company will notify the customer as soon as
possible. Also, you will be advised of your right to file a complaint with the FCC if you believe
it isnecessary.
The telephone company may make changes in its facilities, equipment, operations or
procedures that could affect the operation of the equipment. If this happens the telephone
company will provide advance notice in order for you to make necessary modifications to
maintain uninterrupted service.
If trouble is experienced with this equipment, for repair or warranty information, please
contact our company. If the equipment is causing harm to the telephone network, the
telephone company may request that you disconnect the equipment until the problem is
resolved.
Connection to party line service is subject to state tariffs. Contact the state public utility
commission, public service commission or corporation commission for information.