SKUTCH CK-1P2 User manual

Page 1 of 4
LINE1/2
Connect to Wall Jack
To Audio Source
"Telecommunication Products to solve Telecommunication Problems"
CK-1P2
Promotion-On-
Hold Adapter
(For Panasonic
KX-TG2740,KX-TG2730,
and KX-T2720)
Introduction
Thank you for purchasing
the Skutch CK-1P2
Promotion-On-Hold Adapter
for the Panasonic KX-
TG2740,30,20 two line
cordless phone system. The
CK-1P2 is a true plug and
play device. The unit does not require any "Learning" to operate. When a call is placed
ON HOLD from the base set, or any one of the cordless phones, the caller will hear the
Promotion-On-Hold audio. When the line is re-answered, the audio automatically stops.
It's that simple!
NOTE: If you transfer a call to a Voice Mail Box after a call has been answered by a
live person, Promotion-On-Hold will play over the message.
Installation
1- Position the CK-1P2box under the base telephone with the jacks facing towards the
back of the phone. (See Fig. 1).
Fig. 1
Power Cube
Sensor Board
Sensor Cable
Short Modular Cord
Audio Cord (For CD PlayersONLY)

Page 2 of 4
2- Connect the short modular cord from [1&2 Phone on CK-1]to [LINE 1/2 on Phone].
3- Connect the audio cord from your audio source, to the AUDIO IN jack on the back of
the CK-1 box. For DIGITAL units use the cable that comes with the player.
4- Connect a MOD cord from Telephone Wall Jack 1&2 to [1&2 Line on CK-1].
5- Locate the CK-1P2 "SENSOR BOARD", peel off the white protector papers from the
bottom of the sensor board, and carefully place it OVER the LINE 1 and LINE 2 LEDs
on the Panasonic base set as shown in Fig. #2. Make sure that the numbers on the sensor
board are aligned to the middle of the select buttons on the phone.
6- Connect the Sensor Cable to the Sensor Board.
7- Connect the POWER CUBE from the CK-1 box to 115VAC power. That's it!
Testing the System:
1- Pickup line 1 on your telephone. The No."1" LED on the CK-1P2Sensor Board should
light up.
2- Repeat this test for line 2. If both lines light up when picked up, the CK-1 is working
properly. If either light does not light up, then
a) Make sure that the CK-1P2 and Phone is connected to power.
b) Make sure that the SENSOR BOARD is aligned properly.
Lights on CK-1 Box.
When you place a line on HOLD, the corresponding LED on the rear of the CK-1P2 box
lights up to confirm the Promotion-On-Hold condition.
Fig. 2
Fig. 3
Align to edge
of Phone Display
Connect cable
Align to center'
of phone buttons

Page 3 of 4
Using Other models of telephones
The CK-1P2 will ONLY provide Promotion-On-Hold audio when a call is placed ON
HOLD from the KX-TG2740 base or any of it's cordless telephones. Other models of
telephones can be used with the KX-TG2740, but the Promotion On Hold audio will not
be played to calls placed ON HOLD from these telephones.
Tech Support - 916-786-6186
If you have any problems getting the unit to work properly feel free to give us a call.
Technical Support is available between the hours of 7:30 AM and 4:30 PM Pacific Time,
Monday through Friday.
ONE YEAR LIMITED WARRANTY
This SKUTCH PRODUCT is warranted againstdefects for a period of one (1) year from thedate of the
original invoice. Within this period, we will repair it without charge for parts and labor. To obtain
warranty service the product must be returned, at thecustomer's expense, to SKUTCH Electronics along
with a copy of the original invoice. After the unit has been repaired, SKUTCH will ship the PRODUCT
back via UPS GROUND service at our expense. If any other form of return shipment is requested,the
customer will pay for 100% of theshipping cost.
This Warranty does not apply if in the sole opinion of SKUTCH Electronics, the PRODUCT has been
damaged by lightning or any otherActs of God, or by accident, misuse, neglect, or improper packing,
shipping, modification or servicing by other than an authorized SKUTCH Service Center.
EXCEPT AS SPECIFICALLY PROVIDED IN THIS AGREEMENT, THERE ARE NO OTHER
WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED
WARRANTIES OR MERCHANTABILITIES OR FITNESS FOR A PARTICULAR PURPOSE AND IN
NO EVENT SHALL SKUTCH ELECTRONICS BE LIABLE FOR LOSS OF PROFITS OR BENEFITS,
INDIRECT, SPECIAL, CONSEQUENTIAL OR OTHER SIMILAR DAMAGES ARISING OUT OF
ANY BREACH OF THIS WARRANTY OR OTHERWISE.
ACTA Statement
This equipment complies with Part 68 of FCC rules and the requirements
adopted by ACTA. On the bottom side of this equipment is a label that contains, among
other information, a product identifier in the format US: AAAEQ##TXXXX. If requested,
this number must be provided to the telephone company.
A plug and jack used to connect this equipment to the premises wiring and
telephone network must comply with the applicable FCC Part 68 rules and requirements
adopted by the ACTA. A compliant telephone cord and modular plug is provided with
this product. It is designed to be connected to a compatible modular jack that is also
compliant. See installation instructions for details.
The REN is used to determine the number of devices that may be connected to a
telephone line. Excessive RENs on a telephone line may result in the devices not ringing
in response to an incoming call. In most but not all areas, the sum of RENs should not
exceed five (5.0). To be certain of the number of devices that may be connected to a
line, as determined by the total RENs, contact the local telephone company. For
products approved after July 23, 2001, the REN for this product is part of the product

Page 4 of 4
identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the
REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is
separately shown on the label.
If this equipment causes harm to the telephone network, the telephone company
will notify you in advance that temporary discontinuance of service may be required. But
if advance notice isn't practical, the telephone company will notify the customer as soon
as possible. Also, you will be advised of your right to file a complaint with the FCC if you
believe it is necessary.
The telephone company may make changes in its facilities, equipment,
operations or procedures that could affect the operation of the equipment. If this
happens the telephone company will provide advance notice in order for you to make
necessary modifications to maintain uninterrupted service.
If trouble is experienced with this equipment, for repair or warranty information,
please contact our company. If the equipment is causing harm to the telephone network,
the telephone company may request that you disconnect the equipment until the
problem is resolved.
Connection to party line service is subject to state tariffs. Contact the state public
utility commission,public servicecommissionorcorporation commissionforinformation.