SKUTCH CK-1P7 User manual

Page 1 of 5
"Telecommunication Products to solve Telecommunication Problems"
CK-1P7
Promotion-On-Hold
Module
For use with the KX-TG4500, KX-
TG4000 & KX-TG2000 Phones
For S/N B4020001 and above
Introduction
Thank you for purchasing the Skutch CK-1P7 Promotion-On-Hold Adapter for the
Panasonic KX-TG4500, KX-TG4000 four line, and KX-TG2000 two line cordless phone
systems. The CK-1P7 is a true plug and play device. The unit does not require any
"Learning" to operate. When a call is placed ON HOLD from any cordless phone or the
base station, the ON HOLD caller will hear the Promotion-On-Hold audio. When the line
is re-answered, the audio automatically stops. It's that simple!
NOTE #1: If you are installing the CK1P7 on a two line KX-TG2000, see the "KX-
TG2000 Installation Notes" on page 3 before starting.
NOTE #2: If you transfer a call to a Voice Mail Box after a call has been answered by
a live person, Promotion-On-Hold will play over the message.
Installation
1- Position the CK-1P7 box under the base telephone with the jacks facing towards the
back of the phone. (See Fig. 3).
2- Make sure that the surface on the telephone is clean and free of dust and/or oil.
3- Peel the paper protector off back side of the "SENSOR BOARD" . Carefully align as
shown in Fig. 2. The Sensor Board has been designed to fit the contour of the phone, and
should lock into place. Press down on the Sensor Board to make sure it sticks well.
Audio Cable
Sensor Board
Power Cube
CK1P7 Box
with Adapter

Page 2 of 5
Must cover
Lights on
Phone.
Fig #2
Sensor Board
Line 3 & 4 Line 1 & 2
Connect to Wall Jack
Lines 1 & 2 Connect to Wall Jack
Lines 3 & 4
To Audio Source
Fig #3

Page 3 of 5
4- Connect the short modular cord from [1&2 to Phone] on CK-1 to [LINE 1&2] on
Phone. (Fig #3)
5- Connect the short modular cord from [3&4 to Phone] on CK-1 to [LINE 3&4] on
Phone. (Fig #3)
6- Connect the supplied audio cord to the AUDIO IN jack on the back of the CK-1 box.
Connect the other end, to your audio source. Do NOT use the adapter that came with the
audio cable unless the connector (RCA) NOT fit into your MP3 player. DO NOT plug
the audio adapter into the CK-1 box. (Fig #3)
7- Connect a MOD cord from Telephone Wall Jack 1&2 to [1&2 to Line] on CK-1.
8- Connect a MOD cord from Telephone Wall Jack 3&4 to [3&4 to Line] on CK-1.
9- Connect the POWER CUBE from the CK-1 box to 115VAC power.
KX-TG2000 Installation Notes:
The KX-TG2000 and KX-TG4000 are very similar. The following is a list of the
differences in the installation process between the two phones.
1- When you mount the "SENSOR BOARD" on the telephone, the "3" and "4" on the
SENSOR board will represent line 1 and 2 on the telephone.
2-Connect the short modular cord from [3&4 to Phone] on the CK-1 to [LINE 1&2] on
the Phone.
3- Connect a MOD cord from the Telephone Wall Jack 1&2 to [3&4 To Line] on the
CK-1.
4- The short modular cord that is attached to [1&2 to Phone] on the CK1 is not used.
Disabling Internal Music-On-Hold on KX-TG4500
1. While the base unit is in standby mode, press [MENU].
2. Press DOWN ARROW repeatedly until "Initial setting" is Highlighted, press
[ENTER].
3. Press DOWN ARROW repeatedly until "Music On Hold" is Highlighted, press
[ENTER], then [Enter] again.
4. Press DOWN ARROW once, display should read "Off". Press [Enter] to save.
5. Press [Exit]
Testing the System:
1- Pickup line 1 on your telephone. The line one LED on the SENSOR BOARD should
light up.
2- Repeat this test for lines 2-4. If all lines light up when picked up, the CK-1 is working
properly. If the lights on the SENSOR BOARD do not light up, then
a) Make sure that the CK-1P7 and Phone is connected to power.
b) Make sure that the SENSOR BOARD is flat against the phone.

Page 4 of 5
Lights on CK-1 Box.
When you place a line on HOLD, the corresponding LED on the rear of the CK-1P7 box
lights up to confirm the Promotion-On-Hold condition. After answering the phone, you
MUST wait for a minimum of 3 seconds before you place the line ON HOLD, or the
MOH will not function.
Using Other Brand Phones with the KX-
TG4500/4000/2000 Phone
The CK-1P7 will ONLY provide Promotion-On-Hold audio when a call is placed ON
HOLD from the KX-TG4000 base set or any one of it's cordless phones. You can use
other brand phones with this system as long as the phone will clear a standard ON HOLD
condition on the KX-TG4500/4000/ 2000 phone.
Tech Support - 916-786-6186
If you have any problems getting the unit to work properly feel free to give us a call.
Technical Support is available between the hours of 7:30 AM and 4:30 PM Pacific Time,
Monday through Friday.
•ONE YEAR LIMITED WARRANTY
This SKUTCH PRODUCT is warranted against defects for a period of one (1) year from the date of the
original invoice. Within this period, we will repair it without charge for parts and labor. To obtain
warranty service the product must be returned, at the customer's expense, to SKUTCH Electronics along
with a copy of the original invoice. After the unit has been repaired, SKUTCH will ship the PRODUCT
back via UPS GROUND service at our expense. If any other form of return shipment is requested, the
customer will pay for 100% of the shipping cost.
This Warranty does not apply if in the sole opinion of SKUTCH Electronics, the PRODUCT has been
damaged by lightning or any other Acts of God, or by accident, misuse, neglect, or improper packing,
shipping, modification or servicing by other than an authorized SKUTCH Service Center.
EXCEPT AS SPECIFICALLY PROVIDED IN THIS AGREEMENT, THERE ARE NO OTHER
WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED
WARRANTIES OR MERCHANTABILITIES OR FITNESS FOR A PARTICULAR PURPOSE AND IN
NO EVENT SHALL SKUTCH ELECTRONICS BE LIABLE FOR LOSS OF PROFITS OR BENEFITS,
INDIRECT, SPECIAL, CONSEQUENTIAL OR OTHER SIMILAR DAMAGES ARISING OUT OF
ANY BREACH OF THIS WARRANTY OR OTHERWISE.

Page 5 of 5
ACTA Statement
This equipment complies with Part 68 of FCC rules and the requirements adopted by
ACTA. On the bottom side of this equipment is a label that contains, among other information, a
product identifier in the format US: AAAEQ##TXXXX. If requested, this number must be provided
to the telephone company.
A plug and jack used to connect this equipment to the premises wiring and telephone network
must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant
telephone cord and modular plug is provided with this product. It is designed to be connected to a
compatible modular jack that is also compliant. See installation instructions for details.
The REN is used to determine the number of devices that may be connected to a
telephone line. Excessive RENs on a telephone line may result in the devices not ringing in
response to an incoming call. In most but not all areas, the sum of RENs should not exceed five
(5.0). To be certain of the number of devices that may be connected to a line, as determined by
the total RENs, contact the local telephone company. For products approved after July 23, 2001,
the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX.
The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For
earlier products, the REN is separately shown on the label.
If this equipment causes harm to the telephone network, the telephone company will
notify you in advance that temporary discontinuance of service may be required. But if advance
notice isn't practical, the telephone company will notify the customer as soon as possible. Also,
you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations or
procedures that could affect the operation of the equipment. If this happens the telephone
company will provide advance notice in order for you to make necessary modifications to
maintain uninterrupted service.
If trouble is experienced with this equipment, for repair or warranty information, please
contact our company. If the equipment is causing harm to the telephone network, the telephone
company may request that you disconnect the equipment until the problem is resolved.
Connection to party line service is subject to state tariffs. Contact the state public utility
commission, public service commission or corporation commission for information.