Skutchi SAPslim Cubicle System User manual

slim
Cubicle System
Installation Guide
888-993-3757
skutchi.com

2 Way 3 Way 4 Way End Trim 120 Degree
3 Way
120 Degree
2 Way
Tools Needed
slim
Cubicle System
Identifying Parts
Box Leg C Leg Square Column
Sit-Stand Base
Feet without Casters Feet with Casters
Double Cantilver Corner Worksurface
Support
Right Cantilver Left Cantilver
Acrylic Screen
Mount
Hinge Panel Hooks
1
1/4 Driver
Hex Screws

Connecting Panels
End trim
Panel
Hooks
2
slim
Cubicle System
1A.
1B.
1C.
*No tools are required to lock
SAPslim panels together.
1. Install hooks onto panels first.
Panels connect by one hook
angled north and the other hook
angled south.
2. Once hooks are in place, line
up panels and connect them by
the hooks by sliding one set of
hooks into the other and push
down on panels to lock into place.
3. Install end trim (figure 1D.)
Ex. of hook on panel
To insert end trim, lift up top
cap (see below) then slide
end trim into slot with ridges
facing outward.
End trim Install:
1D.
1C-2.
Top Cap
End trim

Installing Panels on a Connector
slim
Cubicle System
Connecting SAPslim to the Sapphire Cubicle System
3
Connect the panels to the
connector first and then
attach second set of panels.
Top Cap
2 way connector
These attach the same way
as attaching 2 panels togeth-
er (reference figure 1A.).
End trim:
Flip up the top cap and slide
plastic end trim in place.
Snap top cap back down
when finished. (see figure 1D.)
Connector SAPslim
(reference 1A.)
Connector Hex Bolts
SAPslim/Sapphire
Cubicle Connector
1. SAPslim panel and connector
attach the same way 2 panels
connect (reference figure 1A.).
2A.
Hex Bolt
2B.
2. Sapphire Cubicle
panel attaches to
connector by using a
washer and hex bolt.
(figure 2B.).

Attaching Hinges
slim
Cubicle System
4
1. Once you attach the hinges on one panel, be sure to
attach the hinges the opposite way on the second
panel so one is angled north and the other is angled
south(3D). The panels attach to each other by inserting
one hinge into the other(see figure 3F.). Lift Panel up
slightly to insert hinges and connect the panels.
Hinge Assembly
1. Attach hinges to panels. 2. Insert rod into black cover. 3. Insert rod and cover into
hinge that is angled north
on the first panel.
3A.
3B.
3C.
3D.
3E.
3F.
3G.

Installing Feet Support
slim
Cubicle System
5
Panel with feet
To attach panel extender, attach mounts to extender and slide
extender on to panel using the mounts.
Installing panel extender
*Note: If attaching 2 or more
panels together use only one foot
between two panels. (see below).
1. Feet come in two pieces.
Attach each piece to each
side of the panel. Place plate
in between foot and panel
before screwing in the foot.
(See 4A.)
4A.
2. If adding on a wheel to
the hinged panels, simply
screw in the wheel from the
bottom of the panel.
4C.
Mount
Screw
Extender
4D.
Feet without Casters Feet with Casters
4B.
*When using hinges on
connecting panels a wheel can
be added to one of the panels in
place of the foot so the panel
moves more freely. (see below).
Panel with feet (castors)
*If using feet on panels attach them before attaching the panels together.