Courtyard Creations KTS816H-WM User manual

PAGE 1 OF 2
STOP DON’T RETURN TO STORE!
COURTYARD CREATIONS INC.
#5 BOLT M6*14
1
9
5
814
ATTENTION:
Make sure that each bolt needed for all steps matches the
corresponding figure to ensure proper assembly.
STEP 1:
Open the seat/back assembly (#1) and place it on to a non-abrasive
surface, such as a carpet. See Figure 1.
NOTE:
The bolts on the seat/back assembly (#1) should be loose before
assembling the chair. See Figure 1.
STEP 2:
At the rear of the seat/back assembly (#1), fasten the seat and the
back by using bolt (#5) and washer (#8). Keep the bolts loose.
See Figure 2.
FIGURE 2
1
FIGURE 1
HEX.KEY WRENCH 4MM
HEX.KEY WRENCH 6MM
BOLT CAP M6
BOLT CAP M6
BOLT CAP
WASHER d6.5*D13*1.0
BOLT M6*35
BOLT M6*14
BOLT M6*14
SUPPORT BRACE
RIGHT LEG
LEFT LEG
17KAA0101----Y4
SEAT/BACK ASSEMBLY
18000337002
17KAA0201----Y4
18000337006
17C33A0712001Y4
17FA05040301-Y4
18000337004
17C02A0755131Y4
17C33A0722001Y4
62KTS816HQ101
KTS816H-CS03
KTS816H-CS01
KTS816H-CS02
1
1
2
2
10
2
8
13
11
12
9
10
8
7
2
6
1
1
1
1
6
5
3
4
2
PARTS LIST
PART
NO. MATERIAL CODE PART Q’TY
1
KTS816H-WM
ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
SERVICE CENTER TOLL FREE NO.
TEL: [phone]
FAX: [phone]
Use the correct bolts as indicated. Do not tighten any of the bolts until is completely assembled.
Do not discard of any of the packaging until you have checked that you have all of the parts and fittings required.
Keep children away during assembly. This item contains small parts that can be swallowed by children. Children should
always be under direct adult supervision while using this product.
Retain these assembly instructions for future reference.
Quote the following FQC NO. when contacting the service center.
!
!
!
!
!

STEP 8:
Tighten all of the bolts on the seat assembly (#1). After all of the bolts have
been tightened completely, cover them with bolt caps (#9, #10, and #11).
See Figure 8.
STEP 7:
Turn the assembled parts to their upright position. At the rear of the chair, fasten
the seat/back assembly (#1) to the legs (#2 and #3) by using bolts (#7) and
washers (#8). See Figure 7.
STEP 6:
At the front brace of the seat/back assembly (#1), fasten the seat/back
assembly (#1) to the legs (#2 and #3) by using bolts (#6). Keep the bolts
loose. See Figure 6.
STEP 5:
Insert the right leg (#3) into the support brace (#4). Fasten the right leg (#3) to
the support brace (#4) and the seat/back assembly (#1) by using bolts (#5) and
washers (#8). Keep the bolts loose. See Figure 5.
FIGURE 8
STEP 3:
At the front brace of the seat/back assembly (#1), fasten the seat/back assembly
(#1) to the left leg (#2) by using bolt (#5) and washer (#8). Keep the bolts loose.
See Figure 3.
STEP 4:
Insert the support brace (#4) into the left leg (#2). The holes in the support brace
(#4) must be facing the inside of the chair. Fasten the left leg (#2) to the support
brace (#4) by using bolt (#5) and washer (#8). Keep the bolts loose. See Figure 4.
Cleaning and Maintenance
•Wash frame parts and fabric with mild soap and water, rinse thoroughly, Dry frame completely. Do not use bleach, acid, or other solvents
on the fabric or frame parts.
•The chair fabric may be washed on the surface only by using mild soap and water if necessary. Commercial foaming upholstery cleaner
may also be used.
•We recommend the use of furniture covers to protect your chair when not in use.
•Inspect and tighten all bolts or fasteners on a regular basis to ensure the proper performance and safety of your chair.
•In order to prolong the life and beauty of your chair, we recommend that it be stored in a dry and protected area during off season periods.
#7 BOLT M6*35
35
3
4
2
9
7
1
8
FIGURE 7
#5 BOLT M6*14
14
8
5
9
4
2
1
FIGURE 4
#5 BOLT M6*14
14
2
8
5
1
9
FIGURE 3
FIGURE 5
PAGE 2 OF 2
STOP DON’T RETURN TO STORE!
FIGURE 6
NOTE:
The labels marked “L” and “R” on the legs (#2 and #3) should coincide with
Figure 3 - Figure 5 to ensure proper assembly.
R
L
9
9
11
1
2
3
4
8
8
55
99
14
#5 BOLT M6*14
1
3
2
4
10
6
14
#6 BOLT M6*14
L
The store where you made your purchase
does not stock parts for this item.
If you need parts,
whether they are missing or damaged,
STOP!
Missing A Part?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
Call Toll Free:
TEL: [phone]
FAX: [phone]
READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
SEPARATE AND IDENTIFY ALL PARTS, MAKING SURE THAT YOU
HAVE ALL OF THEPARTSLISTED.
IF YOU DO NOTLOCATE ALL OF THE PARTS LISTED, INSPECT THE
PACKING MATERIAL FOR SMALL PARTSTHAT MAYHAVEBECOME
SEPARATED DURING SHIPMENT.
IF YOU EXPERIENCEANY DIFFICULTY DURING ASSEMBLYOR IF ANY
PARTS ARE MISSING OR DAMAGED,CALL THE HELP LINE AT
1-877-539-7436 BEFORERETURNING THIS ITEM TO THE STORE.
PROVIDE THEFOLLOWING INFORMATION WHEN CALLING:
1-MODEL NUMBER OF THEPRODUCT.
2-PARTNUMBER AND MATERIAL CODE OF THE PARTFROM THE PARTS
LIST.
MOST PROBLEMS CAN BERESOLVED WITHOUT RETURNING THIS
PRODUCT TO THERETAILER.