Skyjack SJ63 AJ+ User manual

OPERATION
MANUAL
SJ63 AJ+
ARTICULATING BOOMS
213211AAA
December 2019
ANSI/CSA
To order go to Discount-Equipment.com

We sell worldwide for the brands: Genie, Terex, JLG, MultiQuip, Mikasa, Essick, Whiteman,
Mayco, Toro Stone, Diamond Products, Generac Magnum, Airman, Haulotte, Barreto, Power
Blanket, Nifty Lift, Atlas Copco, Chicago Pneumatic, Allmand, Miller Curber, Skyjack, Lull,
Skytrak, Tsurumi, Husquvarna Target, Stow, Wacker, Sakai, Mi-T-M, Sullair, Basic, Dynapac,
MBW, Weber, Bartell, Bennar Newman, Haulotte, Ditch Runner, Menegotti, Morrison, Contec,
Buddy, Crown, Edco, Wyco, Bomag, Laymor, EZ Trench, Bil-Jax, F.S. Curtis, Gehl Pavers, Heli,
Honda, ICS/PowerGrit, IHI, Partner, Imer, Clipper, MMD, Koshin, Rice, CH&E, General Equip-
ment ,Amida, Coleman, NAC, Gradall, Square Shooter, Kent, Stanley, Tamco, Toku, Hatz,
Kohler, Robin, Wisconsin, Northrock, Oztec, Toker TK, Rol-Air, APT, Wylie, Ingersoll Rand /
Doosan, Innovatech, Con X, Ammann, Mecalac, Makinex, Smith Surface Prep,Small Line,
Wanco, Yanmar
Discount-Equipment.com is your online resource for
commercial and industrial quality parts and equipment sales.
561-964-4949
visit us on line @ www.discount-equipment.com
TO PURCHASE THIS PRODUCT PLEASE CONTACT US
Select an option below to find your Equipment
Equipment Financing and
Extended Warranties Available

This manual is for MEWPs with serial numbers:
SJ63 AJ+: A302 000 001 & Above
Original instructions in English.
To order go to Discount-Equipment.com

SJ63 AJ+ 213211AAA
3
The Safety Alert Symbol identies important safety
messages on MEWPs, safety signs in manuals or
elsewhere. When you see this symbol, be alert to
the possibility of personal injury or death. Follow the
instructions in the safety message.
DANGER
DANGER indicates an imminently hazardous
situation which, if not avoided, will result in death
or serious injury.
WARNING
WARNING indicates a potentially hazardous
situation which, if not avoided, could result in death
or serious injury.
CAUTION
CAUTION indicates a potentially hazardous
situation which, if not avoided, may result in minor
or moderate injury. It may also be used to alert
against unsafe practices.
IMPORTANT
IMPORTANT indicates a procedure essential for
safe operation and which, if not followed, may
result in a malfunction or damage to the MEWP.
Red
DANGER.
Orange
WARNING.
Yellow
CAUTION.
Green
Emergency-
lowering
procedure.
Blue
Safety
information.
THIS SAFETY ALERT SYMBOL MEANS ATTENTION!
BE ALERT! YOUR SAFETY IS INVOLVED.
To order go to Discount-Equipment.com

SJ63 AJ+ 213211AAA
5
Section 1 – About this Mobile Elevating Work Platform (MEWP) . . . . . . . . . . . . . . . . . . . . 9
1.1 Read and heed .....................................................................9
1.1-1 Mobile Elevating Work Platform (MEWP) definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.1-2 Purpose of equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.1-3 Use of equipment ...............................................................9
1.1-4 Operation manual ...............................................................9
1.1-5 Operator ......................................................................9
1.1-6 Service policy and warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.1-7 Ownership of MEWP .............................................................9
1.1-8 Optional equipment .............................................................9
1.1-9 Scope of this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.2 Primary assemblies ................................................................11
1.3 Serial number nameplate ...........................................................12
1.4 Maintenance responsibility ..........................................................13
1.4-1 Operator .....................................................................13
1.4-2 Maintenance and inspection schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
1.4-3 Owner .......................................................................13
Section 2 – General Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.1 Electrocution hazards ..............................................................15
2.1-1 Minimum distance from electrical conductors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.2 Safety instructions ................................................................16
2.3 Fall-protection ....................................................................19
2.4 Worksite inspection ................................................................19
Section 3 – Familiarization ..................................................21
3.1 Overview of the MEWP .............................................................22
3.2 Manual storage box ................................................................23
3.3 Control functions ..................................................................23
3.3-1 Main power disconnect switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.3-2 Footswitch ....................................................................23
3.3-3 Base control console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3.3-4 Platform control console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.4 Features and devices ..............................................................29
3.4-1 Lowered travel position and elevated travel position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
3.4-2 Drive speed ...................................................................30
3.4-3 Drive direction .................................................................30
3.4-4 Tilt switch ....................................................................30
Table of Contents
To order go to Discount-Equipment.com

213211AAA SJ63 AJ+
6
3.4-5 Function restrictions when the MEWP is tilted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
3.4-6 Platform load sensing system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
3.4-7 Overload status ................................................................32
3.4-8 Brake-release system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
3.4-9 Secondary guarding electrical (SGE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
3.4-10 Drive-bypass valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
3.4-11 AC power socket on the platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
3.4-12 Motion alarm ..................................................................34
3.4-13 Differential lock switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
3.4-14 Turret transportation lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
3.5 Optional equipment and attachments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
3.5-1 Flashing amber light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
3.5-2 Welder .......................................................................35
3.5-3 Cold or arctic weather package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
3.5-4 Tool Tray .....................................................................36
3.5-5 Glazier ......................................................................36
3.5-6 Pipe Rack ....................................................................37
3.5-7 Elevate™ telematics - access control unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Section 4 – Inspections Before Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
4.1 Operator’s responsibility ............................................................39
4.2 Visual and daily maintenance inspections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
4.2-1 Labels .......................................................................40
4.2-2 Electrical .....................................................................40
4.2-3 Limit switches .................................................................40
4.2-4 Hydraulic .....................................................................40
4.2-5 Engine compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
4.2-6 Control compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
4.2-7 Base ........................................................................45
4.2-8 Platform assembly ..............................................................47
4.2-9 Boom assembly ...............................................................48
4.2-10 Optional equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
4.3 Function tests ....................................................................50
4.3-1 Do a test of the main power disconnect switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
4.3-2 Do a test of the base keyswitch and the emergency-stop button and light . . . . . . . . . . . . . . . . . . 50
4.3-3 Do a test of the start/function enable/emergency power switch and all the boom and platform
functions .....................................................................51
4.3-4 Do a test of the platform self-leveling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
4.3-5 Do a test of the platform capacity zone indicator lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
4.3-6 Do a test of the emergency power unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
4.3-7 Do a test of the off/base/platform switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
4.3-8 Do a test of the positive air shut-off switch (optional equipment) . . . . . . . . . . . . . . . . . . . . . . . . . 53
4.3-9 Do a test of the emergency-stop button and emergency-stop light on the platform . . . . . . . . . . . 54
To order go to Discount-Equipment.com

SJ63 AJ+ 213211AAA
7
4.3-10 Do a test of the load sensing module self-check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
4.3-11 Do a test of the footswitch and all the boom and platform functions . . . . . . . . . . . . . . . . . . . . . . . 55
4.3-12 Do a test of the platform capacity zone indicator lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
4.3-13 Do a test of the secondary guarding electrical (SGE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
4.3-14 Do a test of the engine start/on/off switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
4.3-15 Do a test of the emergency power unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
4.3-16 Do a test of the manual platform-leveling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
4.3-17 Do a test of the steer function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
4.3-18 Do a test of the drive function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
4.3-19 Do a test of the brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
4.3-20 Do a test of the horn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
4.3-21 Do a test of the elevated travel speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
4.3-22 Do a test of the differential lock switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
4.3-23 Do a test of the oscillating cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
4.4 Operator’s checklist ...............................................................62
Section 5 – Operation ......................................................65
5.1 Energize the base control console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
5.2 Rotate the platform with the base control console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
5.3 Rotate the turret with the base control console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
5.4 Move the jib up and down with the base control console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
5.5 Raise or lower the riser with the base control console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
5.6 Raise or lower the main boom with the base control console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
5.7 Extend or retract the boom with the base control console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
5.8 Make the platform level with the base control console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
5.9 Operate with the emergency power switch at the base control console . . . . . . . . . . . . . . . . . . . . . . 67
5.10 Energize the platform control console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
5.11 Drive forward or rearward ...........................................................68
5.12 Steer ............................................................................68
5.13 Move the jib up and down with the platform control console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
5.14 Move the riser up and down with the platform control console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
5.15 Extend or retract the boom with the platform control console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
5.16 Make the platform level with the platform control console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
5.17 Rotate the platform with the platform control console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
5.18 Raise or lower the main boom with the platform control console . . . . . . . . . . . . . . . . . . . . . . . . . . .69
5.19 Operate the horn ..................................................................69
5.20 Rotate the turret with the platform control console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
5.21 Operate with the emergency power switch at the platform control console . . . . . . . . . . . . . . . . . . .70
5.22 Engage or disengage the differential lock switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
5.23 MEWP shutdown ..................................................................70
5.24 Generator (optional equipment) ......................................................70
5.25 Glazier Tray (optional equipment) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
5.26 Pipe Rack (optional equipment) ......................................................70
To order go to Discount-Equipment.com

213211AAA SJ63 AJ+
8
5.27 Cold or arctic weather package (optional equipment) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Section 6 – Additional Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
6.1 Use the emergency-lowering function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
6.1-1 At the base control console: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
6.1-2 At the platform control console: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
6.2 Chassis tilt recovery ...............................................................74
6.2-1 Platform uphill .................................................................74
6.2-2 Platform downhill ..............................................................74
6.3 Release the brakes manually ........................................................75
6.4 Winch and tow the MEWP ...........................................................76
6.5 Refuel ...........................................................................77
6.5-1 Refuel the MEWP with diesel or gasoline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
6.5-2 Replace the propane cylinder (optional equipment) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
6.6 Move the MEWP for transport ........................................................79
6.6-1 Lock the turret .................................................................79
6.6-2 Hoist the MEWP ...............................................................80
6.6-3 Tie down the MEWP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Section 7 – Technical Diagrams and Specications ..............................83
7.1 Technical diagrams ................................................................84
7.1-1 Reach diagram - SJ63 AJ+ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
7.1-2 Dimensions - SJ63 AJ+ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
7.2 Standard and optional equipment ....................................................87
7.3 Owner’s annual inspection record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
7.4 Specications ....................................................................89
7.5 Environment ......................................................................90
7.6 Tire/wheel specications ...........................................................90
7.7 Maximum platform capacities (evenly distributed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
7.8 Floor loading pressure .............................................................91
Section 8 – Labels ........................................................93
8.1 Engine side ......................................................................94
8.2 Engine compartment ...............................................................97
8.3 Front and rear sides ...............................................................99
8.4 Controls side ....................................................................100
8.5 Control compartment .............................................................106
8.6 Platform ........................................................................109
8.7 Platform control console ...........................................................115
Section 9 – Unique Skyjack Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
To order go to Discount-Equipment.com

SJ63 AJ+ 213211AAA
9
Section 1 – About this Mobile Elevating
Work Platform (MEWP)
1.1 Read and heed
Skyjack is continuously improving and expanding
product features on its equipment; therefore,
specications and dimensions are subject to change
without notice.
1.1-1 Mobile Elevating Work Platform
(MEWP) denition
A mobile machine intended for moving persons, tools,
and material to working positions, consisting of a work
platform with controls, an extending structure and a
chassis.
1.1-2 Purpose of equipment
The Skyjack Articulating Booms Lifts are designed
to move personnel, tools, and materials to working
positions.
1.1-3 Use of equipment
The MEWP is a highly maneuverable, mobile work
station. Work platform elevation and elevated driving
must only be done on a rm, level surface.
1.1-4 Operation manual
The operation manual is an important part of the
MEWP. It is important to always keep a copy of this
manual in the weather-resistant manual storage box of
the MEWP. The manual must be in good condition.
1.1-5 Operator
The operator must read and completely understand
this operation manual, the safety panel label located
on the platform, the limitations, operating procedures,
operator’s responsibility for maintenance and all other
warnings and instructions in this manual and on the
MEWP.
Before you operate the MEWP, make sure you read
and completely understand this information:
1. The full contents of the operation manual,
including the MEWP limitations and the
responsibilities of the operator for the operation,
applicable maintenance and safety instructions.
2. The safety panel label on the platform, the labels
on the MEWP and the attachments.
Compare the labels on the MEWP with the labels in
this manual. Immediately replace any labels that are
damaged or missing.
Only trained and authorized personnel shall be
permitted to operate a MEWP.
The operator must be familiar with the employer’s
work rules and related government regulations.
1.1-6 Service policy and warranty
Skyjack warrants each new product to be free of
defective parts and workmanship for the rst 2 years
or 3000 hours, whichever occurs rst. Any defective
part will be replaced or repaired by your local Skyjack
dealer at no charge for parts or labor. In addition,
all products have a 5 year structural warranty.
Contact the Skyjack Service Department for warranty
statement extensions or exclusions.
1.1-7 Ownership of MEWP
Notify Skyjack of MEWP ownership. If you sell or
transfer the ownership of a MEWP, promptly notify
Skyjack of the new owner’s contact information.
Skyjack needs this information to inform the owner of
any updates or additional activities that are necessary
to keep the machine in proper working condition.
1.1-8 Optional equipment
This MEWP is designed to accept a variety of optional
accessories. Refer to Section 7.2 for a list of the
optional accessories. Operating instructions for these
options are located in Section 5 of this manual.
For components or systems that are not standard,
speak to the Skyjack Service Department. Give the
model and serial number for each applicable MEWP.
To order go to Discount-Equipment.com

213211AAA SJ63 AJ+
10
Section 1 – About this Mobile Elevating Work Platform (MEWP) Read and heed
1.1-9 Scope of this manual
1. This manual applies to the ANSI/SAIA and CSA
versions of the Articulating Boom Lift series. For
a list of applicable models, refer to Section 7.2.
▪Equipment identied with ANSI meets the
ANSI/SAIA A92.20-2018 standard.
▪Equipment identied with CSA meets the
CSA B354.6:2017 standard.
To order go to Discount-Equipment.com

SJ63 AJ+ 213211AAA
11
Primary assemblies Section 1 – About this Mobile Elevating Work Platform (MEWP)
1.2 Primary assemblies
The MEWP has these primary assemblies:
1. Base
2. Turret
3. Boom
4. Platform.
1 Base: The base has these parts:
▪A chassis
▪A steerable front axle
▪A rigid rear axle.
2 Turret: The turret turns 360 degrees continuously.
It has these parts:
▪A compartment on the right side of the turret
which has these parts:
▪Engine
▪Hydraulic pump and motor
▪Battery
▪Swing drive.
▪A compartment on the left side of the turret which
has these parts:
▪Base control console
▪Emergency-lowering system at the base
control console.
▪Hydraulic manifolds
▪Function valves
▪Hydraulic tank
▪Fuel tank.
3 Boom: The boom assembly has these parts:
▪A riser attached to the turret
▪A main boom attached to the riser
▪A jib.
4 Platform: The platform has these parts:
▪Slip-resistant deck surface
▪Hinged tubular guardrails, with mid-rails, and
toe-boards
▪Tri-entry drop bars or an optional swing gate
▪AC power socket
▪Platform control console.
4
3
2
1
To order go to Discount-Equipment.com

213211AAA SJ63 AJ+
12
Section 1 – About this Mobile Elevating Work Platform (MEWP) Serial number nameplate
1.3 Serial number nameplate
The serial number nameplate 1 is located on the
front side of the chassis. It contains this information:
▪Model number
▪Type
▪Group
▪Serial number
▪High-capacity zone and low-capacity zone
▪Capacity and maximum number of persons
▪Maximum work platform height
▪Maximum wind speed
▪Maximum manual force
▪MEWP weight
▪Voltage
▪Maximum incline
▪System pressure
▪Model year
▪Year of manufacture
1
To order go to Discount-Equipment.com

SJ63 AJ+ 213211AAA
13
Maintenance responsibility Section 1 – About this Mobile Elevating Work Platform (MEWP)
1.4 Maintenance responsibility
1.4-1 Operator
Before the beginning of each shift, do all the daily
inspections and function tests. Refer to Section 4.
1.4-2 Maintenance and inspection
schedule
Refer to the service manual for frequent, periodic, and
annual inspections.
The actual operating environment of the MEWP may
affect the maintenance schedule.
IMPORTANT
Only use original or manufacturer-approved parts
and components for the MEWP.
NOTE
Refer to the Skyjack web site (www.skyjack.com) for
machine registration and the latest service bulletins
before you do frequent/periodic or annual inspections.
1.4-3 Owner
The owner is responsible for maintenance inspections
and repairs. Refer to the service manual for the
recommended maintenance and inspection areas and
intervals. Keep a record of the annual inspection on
the label on the cowling of the control compartment.
Refer to Section 7.3 in this manual.
WARNING
Only trained and qualied/competent personnel,
who understand the mechanical procedures, may
do maintenance on the MEWP. The use of a MEWP
that is not properly maintained or in the correct
working condition could result in death or serious
injury.
To order go to Discount-Equipment.com

SJ63 AJ+ 213211AAA
15
Section 2 – General Safety Precautions
WARNING
Failure to obey the instructions and precautions
in this manual could result in MEWP damage,
property damage, personal injury, or death.
It is mandatory that you use this MEWP correctly.
Read this manual and make sure you fully understand
it before you operate the MEWP.
Use personal protective equipment (PPE) when you
do work on or near machinery to protect your eyes,
ears, hands, feet, and body.
Any modications to the MEWP must have written
permission from Skyjack.
WARNING
Do not operate the MEWP if:
▪It does not operate correctly
▪It is damaged or shows worn or missing parts
▪The safety devices are tampered with or
disabled
▪It is locked and tagged for servicing or repair
▪It was modied without permission from
Skyjack and the MEWP owner.
If you do not obey, there is a risk of death or
serious injury.
2.1 Electrocution hazards
The MEWP is not electrically insulated and does not
provide protection from contact with or proximity to
energized electrical conductors. Follow Section 2.1-1
for the minimum distance to keep between all parts
of the MEWP, occupants, or tools, and the electrical
conductors. Consider MEWP movement and electrical
line sway in minimum distance calculation.
If you need to work nearer than 3 m (10 ft), stop and
apply control measures as determined by a qualied
person with respect to electrical transmission and
distribution.
Obey all the national, state/provincial/territorial and
local safety rules.
2.1-1 Minimum distance from electrical
conductors
Voltage Range
Minimum Distance
from Electrical
Conductors
≤ 50 KVA 3 m (10 ft)
> 50 KVA, or if not known
STOP and apply control
measures as determined by a
qualied person with respect
to electrical transmission and
distribution.
DANGER
Electrocution hazard. Keep all parts of the MEWP,
occupants, or tools a safe distance away from
power lines, electrical power sources, or energized
sources. If you do not obey, there is a risk of death
or serious injury.
Keep a minimum safe distance
from sources of high-voltage
power.
DO NOT operate the MEWP
during lightning or storms.
CAUTION
DO NOT use the MEWP as a ground for welding.
If you do not obey, there is a risk of minor or
moderate injury, or malfunction or damage to the
MEWP.
To order go to Discount-Equipment.com

213211AAA SJ63 AJ+
16
Section 2 – General Safety Precautions Safety instructions
2.2 Safety instructions
WARNING
DO NOT operate this MEWP without proper
authorization and training. Failure to avoid this
hazard could result in death or serious injury.
WARNING
DO NOT operate this MEWP in enclosed areas
without adequate ventilation for exhaust gas and
fumes. Failure to follow this warning could cause
death or serious injury.
WARNING
Failure to heed the following safety precautions
could result in tip-over, falling, crushing, or other
hazards leading to death or serious injury.
KNOW all national, state/provincial or territorial, and
local rules which apply to your MEWP and worksite.
MAKE SURE all the safety and instructional labels
are correctly attached on the MEWP in the correct
location. Clean or replace labels that you cannot read.
DISCONNECT and lock out main power disconnect
on the left side of the MEWP when leaving the MEWP
unattended to prevent unauthorized use.
DO NOT wear jewelry or loose
clothing that could become
caught or entangled.
DO NOT allow the
entanglement of ropes, cables
or hoses with the MEWP,
adjacent structures or objects.
Prevent falling from the
platform. Always keep a rm
footing on the platform oor
when working thereon. Do not
climb on the toe-board, mid-rail,
or top-rail. Do not use planks,
ladders, or any other devices
on the platform for achieving
additional height or reach.
MAKE SURE all occupants wear personal fall
protection equipment.
DO NOT raise the platform or
operate elevated in windy or
gusty conditions that exceed
the limits specied in
Section 7.7.
DO NOT increase the surface
area of the platform or carry
large surface area items when
exposed to wind. Increasing the
area exposed to the wind will
decrease the MEWP stability.
MAKE SURE the ground condition assessment
considers the subsurface voids such as cellars,
basements, culverts, and pipes.
DO NOT elevate or drive
elevated on a slope. Elevated
driving must be done on a rm,
level surface.
To order go to Discount-Equipment.com

SJ63 AJ+ 213211AAA
17
Safety instructions Section 2 – General Safety Precautions
DO NOT drive elevated near
depressions or holes of any
type, loading docks, debris,
drop-offs or surfaces that may
affect the stability of the MEWP.
IF OPERATION IN AREAS WITH
HOLES OR DROP-OFFS IS
ABSOLUTELY NECESSARY,
elevated driving shall not be
allowed. Position the MEWP
horizontally only with the
platform fully-lowered. After
ensuring that all 4 wheels
have contact with a rm, level
surface, the platform can be
raised. After elevation, the drive
function must not be activated.
DO NOT drive elevated on a
soft or uneven surface.
DO NOT raise the platform if it
is not on a rm, level surface.
DO NOT ascend or descend
grades greater than the
maximum inclines listed in
Section 7.4. Ascending or
descending slopes must only
be done when fully lowered.
DO NOT operate a MEWP that
has ladders, scaffolding, or
other devices on it to increase
the platform size or work height.
DO NOT exceed the maximum
side force on the platform
capacity label when elevated
(refer toSection 7.7).
DO NOT use the MEWP as a
crane.
DO NOT step on the boom
arm assembly.
DO NOT sit, stand, or climb on
the guardrails.
DO NOT collide or crush.
Be aware of obstructions,
personnel, or other possible
hazards around the MEWP
when elevating, lowering, or
driving. Keep all body parts
inside the platform when
elevating or driving. Be aware of
blind spots when operating the
MEWP.
To order go to Discount-Equipment.com

213211AAA SJ63 AJ+
18
Section 2 – General Safety Precautions Safety instructions
DO NOT use the boom to
push or pull other objects, or to
lift the chassis.
DO NOT elevate the platform
when the MEWP is on a truck,
forklift, or other device or
vehicle.
DO NOT use the MEWP when
the wheels or tires are damaged
(refer to Section 4.2-7).
Make sure the wheel nuts are
tight.
DO NOT alter or disable
limit switches or other safety
devices.
DO NOT use the MEWP without guardrails, lock-
pins and the entry gate/drop bar installed.
DO NOT exceed the rated
capacity of the MEWP.
DO NOT distribute the load
unevenly.
DO NOT use the MEWP under
the inuence of alcohol or
drugs, or if the operator’s
performance is impaired by a
medical condition, the inuence
of prescription or over the
counter drugs, or fatigue.
DO NOT use the MEWP if it
does not function correctly or if
any parts are damaged or worn.
DO NOT leave the MEWP
unattended with the key in the
key switch.
DO NOT operate on slippery surfaces without
sufcient traction to stop, drive, or steer the MEWP.
STUNT driving and horseplay are prohibited.
DO NOT position the MEWP against another
object to steady the platform.
DO NOT place materials on the guardrails
or materials that exceed the connes of the
guardrails unless approved by Skyjack.
Remove all personnel from the platform before
you try to free a snagged platform with the base
controls.
To order go to Discount-Equipment.com

SJ63 AJ+ 213211AAA
19
Fall-protection Section 2 – General Safety Precautions
2.3 Fall-protection
WARNING
Make sure all occupants wear personal fall
protection equipment. If you do not obey, there is a
risk of death or serious injury.
The guardrail system is the primary fall-protection
system of the MEWP platform.
All occupants of this machine must wear personal fall-
protection equipment (PFPE) at all times.
Skyjack recommends the use of a full body harness
with a lanyard. PFPE must be attached only to
approved fall-protection anchorage points in the
platform.
All PFPE must be compliant with applicable
government rules and must be inspected as per the
manufacturer’s recommendation.
WARNING
Fall hazard.
▪Only enter and exit the MEWP using the three
points of contact principle.
▪Only use the equipped access openings.
▪Only enter and exit the MEWP when the
platform is fully lowered.
▪Face the MEWP when entering or exiting the
platform.
Failure to follow these instructions could result in
death or serious injury.
Enter or exit the platform from the ground only. Use
the three points of contact principle, which is when
two hands and one foot, or one hand and two feet are
in contact with the MEWP or the ground at all times.
Face the MEWP when entering or exiting the platform.
2.4 Worksite inspection
Make sure the operating environment, ambient
temperature, Electromagnetic Compatibility (EMC),
and Hazardous Location Rating (locations with
potentially ammable gases, explosive gases or
particles) are appropriate for the MEWP specications
(refer to Section 7.5).
Be sure to follow all national, state/provincial/territorial,
and local rules that relate to operating the MEWP.
Perform a full worksite inspection before operating the
MEWP. Identify potential hazards in the area.
Be aware of moving equipment in the area. Take the
necessary precautions to prevent collisions.
It is the responsibility of the operator to perform a
worksite inspection and avoid/address the following
hazards:
▪Holes or drop-offs
▪Slopes
▪Ditches or soft lls
▪Floor obstructions, bumps, or debris
▪Overhead obstructions
▪Electrical conductors
▪Hazardous locations
▪Inadequate surface support to withstand all load
forces imposed by the MEWP (refer to
Section 7.8)
▪Wind and weather conditions
▪Presence of personnel
▪Other mobile equipment
▪Trafc hazards
▪Equipment that could move and collide with the
MEWP, such as overhead cranes
▪Other possible unsafe conditions.
To order go to Discount-Equipment.com

SJ63 AJ+ 213211AAA
21
Section 3 – Familiarization
WARNING
Do not operate this MEWP without correct training
and authorization. If you do not obey, there is a
risk of death or serious injury.
WARNING
MEWP Familiarization must be given to a qualied
operator. If you do not obey, there is a risk of death
or serious injury.
WARNING
It is the responsibility of the operator to fully
understand, and follow all instructions and
warnings contained in this operation manual and
on the MEWP. If you do not obey, there is a risk of
death or serious injury.
Read and fully understand the operation manual,
all the warnings, and the instruction labels (refer to
Section 8) on the MEWP.
Do these tasks before the operation:
1. Worksite inspection. Refer to Section 2.4.
2. Daily visual and maintenance inspections. Refer
to Section 4.2.
3. Function tests. Refer to Section 4.3.
To order go to Discount-Equipment.com

213211AAA SJ63 AJ+
22
Section 3 – Familiarization Overview of the MEWP
FAMILIARIZATION
3.1 Overview of the MEWP
TM
HOUR METER
QUARTZ
TM
1
2
++
Footswitch
Platform control
console
Base control console
Manual
storage box
Main power
disconnect switch
Drive-bypass valve
Brake hand
pump Brake auto-reset
valve plunger
Secondary
guarding
electrical
Turret transportation
lock
To order go to Discount-Equipment.com