SleepSafe Beds Sleep Safer User manual

PLEASE CHECK ALL BOXES FOR HARDWARE BEFORE DISCARDING
WARRANTY AND USER INFORMATION CAN BE FOUND AT THE END OF THESE INSTRUCTIONS
Thank you for purchasing the SleepSafe Safety Bed. With proper care, your bed will provide years of
safe use. Carefully unpack all the contents of your bed and verify that all parts are included using
the following pages.
TOOLS NEEDED:
At least 2 People
3/8” Wrench
!
Flat-Head Screwdriver
4mm Allen Wrench
(Provided)
7/16” Wrench
(x2)

!
!
!
!!!
! ! 2!
! !
(Extension/Topper Assembly Guide)
(Explanation of the Bed Articulation)
(Detailed Instructions for Assembling your Bed)
(Detailed Instructions for Adjusting Safety Rails)

!
!
!
!!!
! ! 3!
!
!
! !
90mm Allen Bolt
Barrel Nut
(Preinstalled on padded beds)
¼” Allen Wrench
4mm Allen Wrench
T15 Torx Wrench
T10 Torx Wrench
¾“ Hex Bolt
Cardboard Spacer
Locking Pin
Alignment Pin

!
!
!
!!!
! ! 4!
Casters
Frame
Headboard
Safety Rails
Footboard
Mattress
Crank Handle
Front Panel
Back Panels

!
!
!
!!!
! ! 5!
! !
Determine where your SleepSafe Bed® will be positioned:
Depending on the placement of your bed, it may be necessary to move the Crank Assembly to
the opposite side of the bed. If so, set the frame flat on the ground, remove the Assembly using
your two 7/16” wrenches, and reattach using the color-coded guide below.
* Alternate Crank Assembly position should be a mirror image of its original position.
Set Frame on Cardboard Spacers:
!
One person should lift each side at a time while the
other places the blocks underneath the foundation.
* Be sure to leave room to attach the side rails in the next step.

!
!
!
!!!
! ! 6!
!
! !
Prepare Side-Rails (insert Barrel Nuts):
Attach Side Rails to Frame:
!
!
Align Barrel Nut Slot Perpendicular to the edge of the Side Rail.

!
!
!
!!!
! ! 7!
! !
Attach Headboard and
Footboard to Side Rails:
!
Install Casters and
Remove Spacers
!
* Once the caster is inserted, turn the tightening nut as shown above to compress the
rubber sleeve on the stem inside the wood leg, thus preventing the caster from falling out.

!
!
!
!!!
! ! 8!
! !
Attach Back Panel using Alignment Pins
Note: Place the alignment pins in the
holes at the top of the side panel (Fig.
A) then lower the back panel onto the
pins (Fig. B). After the back panel is in
position, secure with 90mm Allen Bolts
using the 4mm Allen Wrench as you did
in the previous step.
!
Install Crank Handles:
Push Crank Handles into
position and then secure
using the Locking Pins
provided.
!

!
!
!
!!!
! ! 9!
Install Mattress:
Install Safety Rails:
!

!
!
!
!!!
! ! 10!
! !
HEAD
FOOT
Crank the handles rotate
clockwise to articulate up and
counter-clockwise to articulate
down. The left handle is for
Head Articulation and the right
handle is for Foot Articulation.
Bed Operation:

!
!
!
!!!
! ! 11!
! !
4mm Allen Wrench
90mm Allen Bolt
Curved End Piece
Extension Side Rail
Topper
(Optional)
Allen Screws
(w/ Topper Only)

!
!
!
!!!
! ! 12!
! !
Set Extension Side Rails on Top of Legs:
You will be assembling the Extension upside-down
Attach Extension Ends to Side Rails:
Attach Ends with Curve Up (smiling) using the 90mm Allem Bolts and 4mm Allen Wrench provided:
*Be sure Screens are facing in (as shown)

!
!
!
!!!
! ! 13!
Flip Extension Assembly over:
Curve-down (frowning)
If you don’t have a Topper, skip Step #4:
!
Attach Topper:
Using the Allen Screws included

!
!
!
!!!
! ! 14!
! !
Loosen Allen Bolts at Top of SleepSafer® Legs:
Loosening the
Allen Bolts before
adding the
Extension allows
for easier
assembly and
tighter fitting. If
you have flip-up
rails, be sure the
proper legs
match up before
tightening all
Allen Bolts.
Assemble SleepSafer®/Extension Combo
Set Extension on top of your SleepSafer® Bed. Insert one 90mm Allen Bolt
into each of the four vacant holes at the top of the legs and tighten using
the 4mm Allen Wrench provided (Shown by “B” above). Tighten all bolts
and your SleepSafer®/Extension Assembly is complete!
Shown at “A” below:

!
!
!
!!!
! ! 15!
!
!
!
!
! !
*Each Safety Rail is pre-adjusted at our factory, but it may become necessary to adjust the Safety Rail height over time.
TOOLS NEEDED:
Rubber Mallet
(or Hammer)
T10 Torx Wrench
(Provided)
T15 Torx Wrench
(Provided)
Determine if your Safety Rails need adjustment:
Insert the T10 Torx Wrench as shown in Fig. 2.
Adjust the screw up or down depending on
which way you noted in Step 1.
(Clockwise = Up / Counterclockwise = Down)
Remove Plastic Strikes:
Use your T15 Torx Wrench to remove the
gold screws holding your plastic strike in
place. Then use a Rubber Mallet to
remove the strike from the leg.
Adjust Accordingly:
Reinsert Plastic Strike:
Place the Plastic Strike back into position and
align by gently tapping it with your Rubber
Mallet.
Fig.!2!
Look at each brass locking-pin when the
Safety Rail is in the locked position as
indicated by “A” in Fig. 1. The pin should
be centered in the hole of the plastic
strike. If it is not, note which way the rail
needs to move (up or down).
A!
Centered!
Fig.!1!

!
!
!
!!!
! ! 16!
*Each Safety Rail is pre-adjusted at our factory, but it may become necessary to adjust the Safety Rail height over time.
Determine if your Safety Rails need adjustment:
With the safety rail in the locked position, check
the spacing between the end of the
safety rail and the headboard
and footboard legs.
The spacing
should be
even!
!
!
Remove Safety Rail and Adjust Accordingly:
If spacing is not even, or there is
too much side-to-side play in the rail,
remove safety rail and turn the black hex
bolt using the ¼”Allen Wrench provided.
B = Clockwise = Increase Play
A = Counterclockwise = Decrease Play
A"
B"

!
!
!
!!!
! ! 17!
!
Full One–Year Warranty:
Limited Five-Year Warranty:
The SleepSafe™ Bed is warranted against defects in workmanship or
materials for a period of one year from the date of purchase. SleepSafe
Beds will repair any defective part at no cost to the purchaser.
During the second through fifth years from the date of purchase,
SleepSafe Beds will replace any part found to be defective. Purchaser
shall pay any service and shipping costs related to the replacement of
the defective part.
*Safety Rails are intended to hinder or discourage the possibility of a roll-out. This product does not take the
place of proper client supervision and monitoring. Any modification to the product or its components will
void the warranty and render the product incapable of fulfilling its intended purpose.
Terms and Conditions:
This warranty applies to normal use and does not cover any damage
caused by normal wear, abuse, misuse, mishandling or modification of
the product.