SleepSafe Beds SleepSafe II User manual

PLEASE CHECK ALL BOXES FOR HARDWARE BEFORE DISCARDING
WARRANTY AND USER INFORMATION CAN BE FOUND AT THE END OF THESE INSTRUCTIONS
Thank you for purchasing the SleepSafe Safety Bed. With proper care, your bed will provide years of
safe use.
Carefully unpack all the contents of your bed and verify that all parts are included using
the following pages.
TOOLS NEEDED:
At least 2 People
3/8” Wrench
Flat-Head Screwdriver
4mm Allen Wrench
(Provided)
Thank you for purchasing the SleepSafe Safety Bed.
Thank you for purchasing the SleepSafe Safety Bed.
With proper care, your bed will provide years of
With proper care, your bed will provide years of
safe use.
Carefully unpack all the contents of your bed and verify that all parts are included using
the following pages.

"
(Up and Down)
(Detailed Instructions for Assembling your Bed)
(Parts required to Assemble your Bed)
(Side to Side)

#
!
! !
#
90mm Allen Bolt
Barrel Nut
(Preinstalled on padded beds)
3mm Allen Wrench
¼” Allen Wrench
T15 Torx Wrench
T10 Torx Wrench
¾“ Hex Bolt
Cardboard Spacer
3mm Handle Bolt
Handle Extension
4mm Allen Wrench

$
Casters
Frame
Headboard
Safety Rails
Footboard
Mattress
Crank Handle
Side Rails

%
Set Frame on Cardboard Spacers:
!
One person should lift each side at a time while the
other places the blocks underneath the foundation.
%
* Be sure to leave room to attach the side rails in the next step.
Determine where your SleepSafe Bed® will be positioned:
Depending on the placement of your bed, it may be necessary to move the Crank Assembly to
the opposite side of the bed. If so, set the frame flat on the ground, remove the Assembly using
your two 7/16” wrenches, and reattach using the color-coded guide below.
* Alternate Crank Assembly position should be a mirror image of its original position.
the opposite side of the bed. If so, set the frame flat
on the ground, remove
the Assembly using
your two 7/16
” wrenches, and reattach using the color
-
coded guide below.
* Alternate Crank Assembly position should be a mirror image of its original position.
* Alternate Crank Assembly position should be a mirror image of its original position.
Note:
The picture shown is
NOT A Hybrid Frame.
A Hybrid Frame will
ONLY have middle
Crank Assembly
(highlighted in
yellow).

&
!
Attach Headboard and
Footboard to Side Rails:
!
Attach Side Rails:
* The Side Rail with the holes goes on the side with the Crank Assembly

'
Install Mattress
Install Casters and
Remove Spacers
!
* Once the caster is inserted, turn the tightening nut as shown above to compress the
rubber sleeve on the stem inside the wood leg, thus preventing the caster from falling out.

(
Install Crank Handles:
Install Crank Handles in the following
order:
1. Crank Extension
2. Crank Handle
3. 3mm Bolt
!
Install Safety Rails:
!
(
* Always install and remove Safety Rails while in their LOWERED position.

)
!
*Each Safety Rail is pre-adjusted at our factory, but it may become necessary to adjust the Safety Rail height over time.
TOOLS NEEDED:
Rubber Mallet
(or Hammer)
T10 Torx Wrench
(Provided)
T15 Torx Wrench
(Provided)
adjusted at our factory, but it may become necessary to adjust the Safety Rail height over time.
Determine if your Safety Rails need adjustment:
Insert the T10 Torx Wrench as shown in Fig. 2.
Adjust the screw up or down depending on
which way you noted in Step 1.
(Clockwise = Up / Counterclockwise = Down)
Remove Plastic Strikes:
Use your T15 Torx Wrench to remove the
gold screws holding your plastic strike in
place. Then use a Rubber Mallet to
remove the strike from the leg.
Insert the T10 Torx Wrench as shown in Fig. 2.
Adjust Accordingly:
Reinsert Plastic Strike:
Place the Plastic Strike back into position and
align by gently tapping it with your Rubber
Mallet.
*+,-!"!
Remove Plastic Strikes:
Use your T15 Torx Wrench to remove the
Use your T15 Torx Wrench to remove the
gold screws holding your plastic strike in
Look at each brass locking-pin when the
Safety Rail is in the locked position as
indicated by “A” in Fig. 1. The pin should
be centered in the hole of the plastic
strike. If it is not, note which way the rail
needs to move (up or down).
.!
/0120304!
*+,-!5!

56
*Each Safety Rail is pre-adjusted at our factory, but it may become necessary to adjust the Safety Rail height over time.
Determine if your Safety Rails need adjustment:
With the safety rail in the locked position, check
the spacing between the end of the
safety rail and the headboard
and footboard legs.
The spacing
should be
even!
!
safety rail and the headboard
safety rail and the headboard
safety rail and the headboard
!
56
Remove Safety Rail and Adjust Accordingly:
If spacing is not even, or there is
too much side-to-side play in the rail,
remove safety rail and turn the black hex
bolt using the ¼” Allen Wrench provided.
B = Clockwise = Increase Play
A = Counterclockwise = Decrease Play
!"
#
remove safety rail and turn the black hex
bolt using the
B = Clockwise = Increase Play
B = Clockwise = Increase Play
A = Counterclockwise = Decrease Play
A = Counterclockwise = Decrease Play
adjusted at our factory, but it may become necessar
y to adjust the Safety Rail height over time.
Safety Rails need adjustment:
With the safety rail in the locked position, check
With the safety rail in the locked position, check
the spacing between the end o
f the
safety rail and the headboard
safety rail and the headboard
safety rail and the headboard

*1
Head
(Up/Down)
Foot
(Up/Down)
Chair Function
(Head & Foot)
(Up/Down)
(Up/Down)
REMOTE LOCK OUT PROCEDURE: PRESS
and HOLD BOTH DOWN BUTTONS on
HEAD and FOOT articulation functions for
about 5 seconds. The light on the
remote will flash when it is locked.
To UNLOCK repeat this procedure.

52!
Full One–Year Warranty:
Limited Five-Year Warranty:
The SleepSafe™ Bed is warranted against defects in workmanship or
materials for a period of one year from the date of purchase. SleepSafe
Beds will repair any defective part at no cost to the purchaser.
During the second through fifth years from the date of purchase,
SleepSafe Beds will replace any part found to be defective. Purchaser
shall pay any service and shipping costs related to the replacement of
the defective part.
*Safety Rails are intended to hinder or discourage the possibility of a roll-out. This product does not take the
place of proper client supervision and monitoring. Any modification to the product or its components will
void the warranty and render the product incapable of fulfilling its intended purpose.
Terms and Conditions:
This warranty applies to normal use and does not cover any damage
caused by normal wear, abuse, mi
suse, mishandling or modification of
the product.