Sliger CL520 User manual

CL520
Console Style Mini-ITX PC Case for 2-slot GPU

SCREWS
The CL520 comes with a total of 7 dierent screws. For the purpose of
this guide we will assign a unique color to each of the screws, signifying
their locations within the case.
CYAN M4 .7 x 5mm FLAT HEAD
Base Plate
Other exterior bracket
VIOLET 6-32 x 1/4” HEX HEAD
Motherboard
Power Supply
RED M3 x 5mm FLAT HEAD
Power Cord Mount Bracket
SSDs / SSD brackets
GREEN M3 x 6mm PAN HEAD
Securing PCIe Cards
PINK M3 x 8mm FLAT HEAD
Power Cord
M3 x 12mm FLAT HEAD
Fan
Fan Bracket
GREY M4 x 25mm SOCKET CAP
Case Handle

TOOL-LESS TOP PANEL
The CL520 top features tool-less removal via ball-stud mounting points. Grasp the
lip on the rear of the cover panel and pull upward to remove. The front ball studs
may require altering the angle you are pulling from to release.
Note: This panel may be very tight on the rst few times on/o! Use caution with
using extreme force to avoid damage.

Additional installation instructions for your CPU, CPU cooler, RAM,
etc. are covered by your motherboard or coolers respective user
manual.
Be sure to install your IO shield rst!
Some CPU coolers may require a back plate installed before installing the
motherboard. It is advised for the CL520 to also check that any M.2 mounts on
the back of motherboard have drives installed before installation of the
motherboard, as there are no SSD or HDD mounting points inside the case.
Once the IO shield is properly installed the motherboard can now be mounted
using 4x 6-32 x 1/4” HEX HEAD screws.
A Phillips #2 screw driver with a minimum 3” shaft length
is recommended for installing these screws.
MOTHERBOARD

POWER SUPPLY
Remember to connect all required modular power cables FIRST
The power supply should be positioned with the fan side towards the top of the case.
This orientation will result in better overall system temperatures and lower noise.
Once positioned, the SFX PSU can be attached to the PSU Mounting Bracket
with up to 4x 6-32 x 1/4” HEX HEAD screws and then mounting bracket to case
with 3x 6-32 x 1/4” HEX HEAD screws.

INSTALLING CASE FANS
Use 4x M3 x 12mm FLAT HEAD screws to attach the fan guard. Place
fans into chassis sliding in the BLUE fan studs. Follow the proper orientation of
the fan guard in photo below and the fans MUST exhaust air out of the case.

GPU MOUNTING
The process of installing the GPU is same as it would be on a standard
case setup, just on a PCIe riser. Slide the card into position, push down
into the slot, and then secure the PCIe card bracket with
2x M3 x 6mm PAN HEAD screws.

POWER CORD
The power cord extension is then installed into the bracket with
2x M3 x 8mm FLAT HEAD. Once the Power Cord has the bracket
attached and power cable is routed through the case to the PSU.
NOTE: The CL520 Pigtail option is to increase max GPU card height to
157mm where as the standard option only allows for a card height of
133mm.
Pigtale Standard

CABLE MANAGEMENT
The power switch/LED is routed and
plugged into the motherboard.
The power cord is mounted above
PCIe Slots and properly screwed to the
cover plate or passed through
the grommet, and routed to the
inlet on the power supply if using the
pig tail conguration.
(Also be sure to check that your
PSU switch is set to on!)
Motherboard power cables are
plugged in, and GPU power
cables are loosely positioned.
Power cables are loosely managed
and zip tied.
The PCIe riser is plugged into the
PCIe slot on the motherboard.

CASE HANDLE
The Case Handle is attached with 2x M4 x 12mm SOCKET CAP.
Use the included Allen key to tighten.
NOTE: Do not over-torque screws

BASE PLATE
Base plate is attached with 2x M4 .7 x 5mm FLAT HEAD
Along with optional 4 rubber feet that can applied to the corners.
NOTE: Slot cut-out goes under PCIe Slots. Do not over-torque screws